轉換扭矩 的英文怎麼說
中文拼音 [zhuǎnhuànniǔjǔ]
轉換扭矩
英文
wechselmoment alternating torque- 轉 : 轉構詞成分。
- 換 : 動詞1. (給人東西同時從他那裡取得別的東西) exchange; barter; trade 2. (變換; 更換) change 3. (兌換) exchange; cash
- 扭 : 動詞1 (掉轉; 轉動) turn round 2 (擰; 旋轉) twist; wrench 3 (擰傷) sprain; wrench 4 (走路時...
- 矩 : 名詞1. (畫直角或正方形、矩形用的曲尺) carpenter's square; square2. (法度; 規則) rules; regulations 3. [物理學] moment
- 轉換 : change; transform; convert; switch
- 扭矩 : torsion; torque; twist; lay; moment of torque; moment of torsion
-
Centrifugal clutch 18 is provided to mechanically couple power source 12 to work device 14 as the speed of input 15 of work device 14 increases to a predetermined speed wherein the need for the torque and speed conversion provided by non - grounded multi - stage transmission 22 become less necessary
離心式離合器18設為隨著工作裝置14的輸入15的速度增加到預定速度時將動力源12與工作裝置14機械連接,此時逐漸不再需要非搭鐵多級變速器22提供的扭矩和速度轉換。In this paper, the control of dynamometer, part of test platform is accomplished and the driver of data collection card is designed
設計了用於扭矩信號、轉速信號等模擬數據向數字信號轉換的數據轉換卡的驅動程序。Delay is obvious in large body because of its inertia, moment force, stress and gearing. transfer of electical cell increases the delay. this paper points out that the delay can be compensated by using the smith control algorithm. the result of computer emulation proved that a better quality is gained by using the algorithm on heavy nc machine
大慣量物體,由於其慣性,加之傳動鏈長,所需的扭矩大,引起的應變大,加上電氣轉換元件的滯后,故滯後效應明顯.該文提出用史密斯控制演算法將滯后進行補償.計算機數字模擬結果說明,對大慣量有滯后的重型數控機床,應用該演算法能得到較好的控製品質The paper research a predominant variable torque clutch ? hyperboloid clutch with rollers. the clutch makes convert mutually between force and torque reality to control transmission with special geometry relation and friction transmission. it is satisfy with the request of modern industry
本文所研究的是一種性能優越的可變扭矩加載器?雙曲面滾柱加載器,利用加載器接觸表面特殊幾何關系,通過接觸表面的摩擦傳動,實現軸向力與轉矩之間的相互轉換,從而達到控制制動和傳遞動力的目的,可滿足現代工業對加載裝置的要求。The principal axis torsion angle, produced by torque, is converted to two channel square waves with phase difference through grating sensor. then the degree of torsion angle is measured by data collection card. finally the value of torque and the other parameters of the axis can be calculated by upper pc
將主軸受扭矩作用而產生的扭轉角,通過光柵傳感器轉換為兩路有相位差的方波信號,再通過數據採集系統檢測出扭轉角的度數,最後由上位pc機計算出扭矩的大小和主軸的各種參量。A new type of pressure coefficient cp is defined to lead to a linear correlation with radial locations, which will lead to a curve correlation with radial locations with conventional definition of cp. the correlations of cm, nuave and cp with rotational reynolds number have been got through the computation with rotational reynolds number from zero to 1. 0 108
給出了扭矩系數cm 、平均換熱系數nu _ ( ave )隨旋轉雷諾數變化的關系式,發現它們與沒有預旋時是完全不同的,當re _ = 0時, cm 、 nu _ ( ave )不為零,而具有一個初值。Finally, the torsional vibration of a rigid disk resting on the saturated grounds under the general torque is primarily discussed by the means of laplace - hankel transform. the general solutions of the torsional moment, stress and displacement are given and the numerical solutions in special cases are also obtained
最後,本文還採用laplace - hankel聯合變換技術初步分析了在一般動扭矩作用下飽和地基上剛性圓板的扭轉振動問題,給出了扭矩、應力和位移的通解,並給出了特例情況下的數值解。Also, the harmonic resonance frequency was lowered to that of below idle - allowing us to shut out the unwanted vibrations often caused by the twisting force generated by the engine during torque rate changes
諧振頻率可以降到怠速以下,在轉矩變換期間由發動機扭矩產生的震動可以排除。The force transducer arranged as an external support between motor and supporting structure monitors the functional safety of the electric drive via the torque
力轉換器作為馬達和支撐結構之間的外部支柱,通過扭矩監控電動驅動裝置的運轉安全。In the system, the rotate speed sensor and torque sensor are fixed between the engine power output shaft of yanmar combine harvester and the power input shaft of working device. the signals of torque and rotate speed are preprocessed such as v / f, amplified. and the power is computed
該系統在洋馬聯合收割機的發動機動力輸出與工作裝置的動力輸入軸之間安裝了轉速和扭矩傳感器,對轉速和扭矩傳感器的輸出信號進行v f轉換、放大等預處理,並計算出功率值。分享友人