轉數變換器 的英文怎麼說
中文拼音 [zhuǎnshǔbiànhuànqì]
轉數變換器
英文
revolution converter-
At present, the typic harmful current detection methods are the fast fourier transform algorithm in frequency domain and methods based on the instantaneous reactive power theory, these methods all require some transform and quick, real - time calculating, so high precision analog multipliers or high speed dsp chip with fast a / d are needed, this results in complex circuit and high cost ， which have restricted the development of apf
目前畸變電流檢測常用的方法有頻域法的fft和基於瞬時無功理論的畸變電流檢測法。這些方法均有一定的變換，需要快速、實時運算，因此必須使用高速的數字微處理器和高性能a / d轉換器，這必將大大提高系統成本，使得電路結構復雜，在一定程度上限制了有源濾波器的發展。To utilize the advantages of dsp chips, the system should be computing sources economical. according to digital signal processing theory, the poly - phase fir can help reduce the workloads of the ddc / duc. therefore, adding the complex carrier mixers, the channelization system ( a method of using a single wideband facility to transmit many relatively narrow - bandwidth signals. by subdividing the frequency spectrum used in the wideband channel ) can be formed utilizing the characters of fft
為了使開發出的軟體可以適用於高速dsp器件開發，節省系統資源，課題首先從數字信號處理的理論進行分析，得出可以利用抽樣率轉換的數字濾波器的特點，即多相濾波實現數字上下變頻計算負擔的減小，之後進一步將多相濾波器與頻譜搬移部分結合，通過公式的推導，得出可利用快速傅立葉變換的特點實現多路信號的通道化發射和接收的處理模型。A technique of 3 - point positioning of welding seams with structure - light visual sensor is presented. with this technique, arc - welding robots can cope with the location variation of weld seams each time in batched manufacturing. on the base of suitable mathematical description, the localization problem is transformed into determining a displacement transformation matrix
在此系統中利用機器人結構光視覺三點焊縫定位技術，使弧焊機器人可以適應批量生產中每次焊縫位置的變化，通過適當的數學描述，將焊縫定位問題轉化為確定位姿變換矩陣。Through analysising the characteristics of the power system with floating neutral point deeply, the paper puts forward a new plan of single - phase to ground fault line selection on the base of s ' s signal injecton method and gives the hardware and software design. in this design, the high speed sampling and data processing is carried out through using dsp processor ; the large electrice current is drived through the application of a high - performance audio power amplifier and transformer ; the communication between host computer and detectors is realized through rs485 bus technology ; the difference multilevel frequency - selected amplifier is designed and the feeble signal of space is sampled on the base of the theory of magnetic induction ; the interface between dsp and exterior chip and rs485 interface logical is designed through using fpga ; the using of lcd module and keyboard interfacing chip makes the interface between human and machine ; the programme of host computer and detectors is designed through using blocking design method
在本設計中，採用高速的dsp處理器，實現了對故障特徵信息的高速採集與處理;採用大功率的功放晶元與變壓器配合的方法，實現了大電流信號的驅動輸出;採用485總線技術，組建了裝置主機與多探測器之間的主從式通訊網路，實現了多干擾條件下裝置主機與多探測器的可靠通訊;設計了差分式多級選頻放大電路，採用磁感應的方法實現了對空間微弱信號的接收;利用fpga技術，實現了控制器與多外設的介面及數字信號的串並轉換;採用了先進的lcd液晶顯示模塊及鍵盤介面晶元，設計了人機信息交互的介面;採用了模塊化的軟體設計方法，開發了裝置主機及探測器的軟體程序。The format transcoding includes the frame size conversion, frame rate or field rate conversion, and interlaced / progressive video conversion. in this chapter, the frame size trancoding with arbitrary rational number ratio of l / m is put forward
提出了變換比例為任意有理數l m時的空域任意尺寸轉碼，以及針對任意尺寸轉碼器的運動矢量重用演算法。At the aspect of hardware design, it adopts pulse distributor and the technology of single polar voltage drive to accomplish the function of controlling and driving stepmotor ; it adopts the technology of pulse width modulation and cmos h - bridge drive to accomplish the function of controlling and driving dc servomotor ; it adopts d / a convertor to accomplish the function of controlling ac transducer ; it adopts the technology of digital phase detection to accomplish the function of detecting the feedback position signal of induction phase shifter ; it adopts dsp ’ s capture cell to accomplish the function of detecting the feedback position signal of photoelectric coder
硬體方面，採用脈沖分配器和單極性電壓驅動技術實現了步進電機的控制和驅動功能;採用脈寬調制技術和cmos互補h橋驅動技術實現了直流伺服電機的控制和驅動功能;採用d / a轉換器實現了交流變頻器的控制功能;採用數字化相位檢測技術實現了感應移相器位置反饋信號的檢測功能;採用dsp的捕獲單元實現了光電編碼器位置反饋信號的檢測功能。Aimed at design index of input power 1. 5kw, most output rotate velocity 300rpm, and rating output rotate velocity 150rpm, considering factors of angle and ratio of transmission, on the basis of kinematics simulation, author optimized the kinematics parameters. in this paper, author has made some analysis and study to the primal assembly condition of transformer ' s sequential action in theory, designed structure dimension of the input and output transformer, and verified the corresponding strengthen. further, the structure, which is to key transmission components of velocity control system of the speed regulator, has been designed based on meeting operational sensitivity, precision and self - locking
本文針對輸入功率為1 . 5kw ，最大輸出轉速，額定輸出轉速的無級變速器的設計要求，並考慮到傳動角及變速比等因素，在運動學模擬的基礎上，對運動學參數進行了優化；本文對變換器連續作用的初始裝配條件進行了理論分析與研究，對輸入、輸出變換器作了結構尺寸的設計，並進行了強度校核計算；本文還對變速器調速系統中主要傳動構件在滿足操作的靈敏度、精度、自鎖性的基礎上進行了結構設計；最後採用workingmodel3d軟體，進行虛擬樣機的計算機輔助模擬設計及運動學和動力學計算。The study has completed the design of two - phase inverter and made up of the two - phase inverter - motor system for experimental use it is a variable frequency adjustable speed system with a open - loop control of rotational speed, which consists of voltage - controlled oscillator circulating assign device inverter circuit and two - phase induction motor a accurate mathematical model is set based on the whole system, and simulator program of dynamic and steady condition is established, which is used to calculate the dynamic and steady performance by kron and symmetrical coordinate converter by simulator calculation and experimental research with specific parameter of the system, a comparison is made between predicted and experimental characteristics, experimental measurements are shown to compare closely with corresponding theoretical result it is compared with some variable frequency adjus table speed system comprising inverter and single - phase induction motor from the system efficiency torque pulsation and the effect of two - phase inverter capacitance based on the conclusion, harmonic cancellation pulse width modulation control of a two - phase inverter - fed induction - motor drive system is researched, which cancelled the low harmonic and improve the system performance
通過對電機的kron變換和對稱分量變換，建立了系統較精確的數學模型，編制了系統動態及穩態運行的模擬計算程序分別計算系統的動態和穩態性能。通過對系統的具體參數進行了模擬運算和實驗研究，實驗和模擬結果進行比較，說明實驗和理論較為一致，並從系統效率、轉矩脈動及兩相逆變器電容的影響等方面與各種逆變器和單相異步電動機組成的變頻調速系統加以比較。在此基礎上，對兩相逆變器供電-異步電動機系統使用諧波抑制pwm控制進行了研究，由於減少了低次諧波，改善了系統性能。Firstly, the whole scheme of the transducer is designed, the transducer includes capacitance / voltage converting, ripple - control capacitor switching, magnify - multiple switching, a / d converting, singlechip, photoelectric isolation and rs - 485 serial communication, etc. the measurement of microcapacitor is the key technology of transducer
首先對變送器部分進行了整體的方案設計，變送器由電容/電壓轉換、紋波控制電容切換、放大倍數切換、 a / d轉換、單片機、光電隔離和rs485串口通訊等幾部分組成。At present, people usually use birefrigence and quasi - phase - matching methods to achieve higher effiency in the process of conversion. a significant advantage of quasi - phase - matching method is that the interaction is occurred through the largest element of the x ( 2 ) tensor ; the period of optical superlattice can be designed randomly, and any interaction can be matched without walk - off angle ; they are fitted to be used in frequency conversion of lower power especially. the quasi - phase - matching method has some advantages over birefrigence method, improving the efficiency of frequency conversion ; the range of frequency conversion covers its whole transperant wavelength
由於準相位匹配技術有其獨特的優勢，可以利用非線性光學晶體的最大二階極化張量，如ppln 、 pplt 、 ppktp用的非線性極化張量都是d _ （ 33 ） ，其有效非線性系數高出普通非線性光學介質（如bbo 、 lbo 、 ktp ）一個數量級，而且可以人為靈活設計調制周期，通過周期設計其頻率變換范圍可以覆蓋準相位匹配介質的整個透明波段，選擇無走離效應，解決了常規pm難以解決的問題，拓寬了非線性晶體的應用范圍，極大地提高了頻率轉換效率，已成為非線性光學材料和固體激光器的研究熱點之一。The main circuit is consisted of 18 thyristors circuit and protection circuit. with the help of control subsystem, it can get the output of low frequency voltage ( current ) with the shape of sine wave ; the core of the control subsystem is the cpu of 87c196kc, and the synchronization circuit, the pulse - widen circuit, and the power - enlarged circuit form the accessorial subsystem of the control system. it possesses all the functions of digital triggering, digital tuning, analog / digital conversion ; the input transfer can isolate the input and output ; and the circumfluence reactor can reduce the circumfluence
主迴路採用由18個晶閘管組成的三相零式電路，並輔以晶閘管的保護電路，通過控制可以得到低頻正弦波的電壓（電流）輸出；控制迴路主要以87c196kccpu為核心，其外圍電路包括同步電路，脈沖拓寬電路，功率放大驅動電路等，完成了數字觸發、數字調節、模數轉換等功能；進線電源變壓器具有變壓和隔離作用；環流電抗器則實現了有效抑制主迴路瞬時脈動環流的功能。There is difference frequency measurement requirement for every part of pid regulating, difference between dynamic quality and static quality in response time and accuracy. according to these, it use the interrupt functions and high - speed counter of the simens s7 - 200 plc cpu226 basic unit and some peripheral circuit to measure frequency ; in software designed, the procedure frame of hydraulic - turbine governor and disperse process of parallel pid are analyzed, an improved pid algorithm is adopted to realize a pid regulation mode with variable structure and parameters ; the mechanical liquid - pressure system of the hydraulic - turbine governor is with electric - hydraulic converter unit of step motor. according to the drive character of five phase of response step motor, a variable frequency regulated voltage driver unit is designed in order to realize interface between plc and driver of step motor
本文利用s7 - 200plc自身的特點設計了頻率測量單元，根據pid調節各個環節的特點，以及調速器動態特性、靜態特性對頻率測量的實時性和精度要求的不同，利用s7 - 200plc基本單元中內置的高速計數器以及相應的外圍放大整形、分頻電路，實現了水輪發電機組頻率的測量；在軟體上，對微機調速器的整個程序框架、並聯pid的離散化過程進行了分析，選用改進的pid演算法實現了變參數、變結構的pid調節模式；調速器的機械液壓隨動系統具有步進電機電液轉換元件，採用五相反應式步進電機，根據其驅動特性設計了變頻調壓驅動器，實現plc與步進電機驅動器之間數字介面。Electrical measuring tranducers for converting a. c. electrical quantities to analogue or digital signals
交流電量轉換成模擬信號或數字信號用電氣測量變換器Electrical measuring transducers for converting a. c. electrical quantities to analogue or digital signals
交流電量轉換成模擬信號或數字信號用的電氣測量變換器Electrical measuring transducers for converting a. c. electrical quantities to analogue or digital signals ; amendment 1
交流電量轉換成模擬信號或數字信號用的電氣測量變換器.修改件1Electrical measuring transducers for converting a. c. electrical quantities to analogue or digital signals ; amendment 2
交流電量轉換成模擬信號或數字信號用的電氣測量變換器.修改件2With promulgation and obliging actualization of iec 1000 - 3 - 2 etc. international standards, power factor correction ( pfc ) technique become a hotspot of research in power electronics field. based on average current mode, the paper introduce the design and implementation of a fully digital controlled single - phase boost power factor corrector with fast response. the control - loop circuit is realized using digital control and the corrector can tend to unity power factor, lower current harmonics and high transfer efficiency
本文在平均電流模式控制的有源功率因數校正技術的基礎上，設計了一種控制電路基於數字信號處理器（ dsp ） 、主電路採用boost變換器拓撲結構的全數字單相功率因數校正器，用數字電路代替傳統的模擬電路來實現對整個迴路的控制，最終使得校正器具有輸入功率因數接近於1 、低電流諧波以及高轉換效率的特性。This dissertation first discusses the two - dimension interpolation algorithm and coordinate rotation digital computer algorithm involved in the process of designing system. then the paper particularly probes into the research and development of b - mode digital scan converter, m - mode digital scan converter and graphic circuitry in the digital scan conversion system
本文首先對系統設計過程中引入的二維線性插值演算法和坐標旋轉數字計算演算法進行了討論，然後著重論述了數字掃描變換系統中的b型數字掃描變換器、 m型數字掃描變換器和圖形界面電路的原理、設計與實現。The mc controlled by this strategy not only achieves the dtc of asynchronous machine with excellent dynamic performance but also acquires good input currents and an adjustable power factor
按這種策略進行控制的矩陣式變換器，既可實現對異步電機進行動態性能優良的直接轉矩控制，又可獲得良好的輸入電流波形以及可調的功率因數。Resolving - transformers is a kind of component that converts the rotor corners to electrical signals, one has sine functional relationship with the rotor - comers, while the other has cosine ones, and this component has been widely used in many fields such as automatic controls, aviation and firepower fields to implement the information transmission of shaft - angle between systems
正餘弦旋轉變壓器是一種將轉子轉角變換成與之成正餘弦函數關系的電信號的元件，被廣泛應用於自動控制、航空、火力控制等領域，以實現系統之間軸角信息的傳輸功能。分享友人