轉盤塔 的英文怎麼說
中文拼音 [zhuǎnpántǎ]
轉盤塔
英文
rotary disc column-
This drilling adopts crank connecting link and walking beam percussion mechanism, which make the drilling possess two percussive functions, normal drilling takes connecting link impact as main mode, when encountering special situation and the connecting link impact can not drill, it can transform into hoisting impact, the stroke length can be modulated, it realizes automatic percussive drilling due to continuous operating of connecting link percussive mechanism, these can enhance drilling efficiency and relieve labor intensity ; it adopts pumping reverse circulation to drain slag, which not only resolves the drilling difficulty in special stratum such as pebble and gravel stratum and hard stratum, but also resolves the problem that the percussive drill ' s efficiency is low ; it adopts spur gear differential mechanism as double cylinders lazy tongs of main hoist, which not only ensures the balance state of drilling tool, but also reduces the mechanical design, and reduces the cost ; the bottom plate traveling motion of this drilling machine adopts walking type ; the drilling tower adopts hydraulic pressure uprising, and reduces the assistant operating time
該鉆機採用曲柄連桿、游梁式沖擊機構，使鉆機具有兩種沖擊功能;正常鉆進以連桿沖擊為主，遇到特殊情況，用連桿沖擊不能鉆進時，可轉為卷揚沖擊，沖程可調，因連桿沖擊機構連續工作，所以實現了自動沖擊鉆進，可提高鉆進效率，減輕勞動強度;採用泵吸反循環的方式排渣，既能有效解決卵礫石地層、堅硬地層等特殊地層鉆進的困難，又很好地解決了沖擊鉆機效率低下的問題;採用直齒圓柱齒輪差速機構作為主卷揚的雙筒同步機構，既保證了鉆具處于平衡狀態，又大大簡化了該機構設計，降低了成本;該鉆機底盤行走移位採用步履式;鉆塔採用液壓起立，減少了輔助作業時間。The japanese tower, laden with the satellite dishes and transmitters of six tv stations, will retain, for the time being, the crown of “ world ' s tallest communications tower ”
這個日本的蘇米達塔，附設有衛星定向盤和六個電視臺的轉播發射器，它將在竣工之時保持著「世界最高通訊塔」的桂冠。Based on the hydrodynamic, by using momentum theory to the liquid in the flow channel, the computational formula of the air exciting - vibration force is acquired. by using four - step runge - kutta method, the periodic response results of the elastic rotor system with one single - disc are gained. then the dynamic characteristics of the rotor system at the certain rotate speed and the certain physic parameter of system are analyzed by using the phase spaces and poincare maps of this system
基於流體動力學，通過對葉片流道內的流體模型應用動量定理，得到此汽流激振力模型，並採用四階龍格庫塔法，得出了單盤彈性轉子系統的周期響應規律，然後根據系統的相軌跡及poincare映射圖，分析了系統在特定轉速及特定的轉子系統參數下的運動特徵。The ratio of story shear rigidity as well as the equivalent lateral rigidity ratio of story above the transfer story to the story under the transfer story should be designed properly to avoid the transfer story becoming weak story, thus the shear walls and the columns in the large base will not yield before the elements above the transfer story ; ( 2 ) the translation - torsion coupled effects and the vibration in the plane should be considered in analysis of structure with large base and muti - towers
轉換層的設計除應控制層剪切剛度比外，還應控制轉換層上部與下部結構的等效側向剛度比以避免薄弱層出現在框支層，保證地震作用下落地剪力墻和框支柱不先於轉換層上部結構進入屈服狀態；大底盤多塔樓結構的分析必須考慮平扭耦聯振動和樓板平面內振動的影響。In this paper, three - tower building with name of oriental tunes square in xiamen is analyzed by the international current program sap2000, considering seismic action in two directions. by structural modeling and calculation, the characteristic of vibration of the multi - tower structure is analyzed, the influences of the rigid ratio of the enlarged base to top tower and translation - torsion coupled effects among several towers are investigated, the inter - story displacement, displacement of the top tower and deformation of tower ' s base floor in x and y major orientation under earthquake action are contrasted with those under wind load. at last, the distributing characteristics of stress of transfer plate and of the normal, shearing stress of mostly vertical elements under earthquake action are studied
本文以具有3個塔樓的廈門東方時代廣場為分析對象，採用國際通用有限元分析軟體sap2000進行結構建模和分析，考慮雙向地震動輸入，研究結構的振動特性，分析底盤與塔樓剛度比對結構的影響以及多塔之間的扭轉效應和平扭耦聯作用，對比風荷載和地震作用下塔樓在兩個結構主軸方向的層間位移、頂點位移以及塔樓底層的變形，分析地震作用下轉換層樓板的應力分佈特點及主要豎向構件的正應力和剪應力分佈特點。Rotary tool turret with 12 vdi rotary tool position is prepared for any rotary tools for x axis and z axis, which are used for milling, boring and tapping
回轉刀塔的刀盤提供了12個vdi旋轉刀具的安裝位，允許在刀盤的任意刀位上安裝x向或z向的旋轉刀具。從而實現銑、鉆、攻絲等加工功能。分享友人