近似坐標 的英文怎麼說

中文拼音 [jìnzuòbiāo]
近似坐標 英文
approximate coordinates
  • : Ⅰ形容詞1 (空間或時間距離短) near; close 2 (接近) approaching; approximately; close to 3 (親...
  • : Ⅰ名詞1 [書面語] (樹梢) treetop; the tip of a tree2 (枝節或表面) symptom; outside appearance; ...
  • 近似 : approximate; similar; approach; approximation; roughness; propinquity
  1. After coordinate transformation, we can get the approximate confidence region of parameters in virtue of the approximate expression of e

    然後利用變換,藉助e ~ x的式,用數值方法求解獲得參數的置信域。
  2. The improvements in the iaga contained adding strengthen operator, improving evaluation index of premature, etc. multi - phase homing project, making use of the flight properties of parafoil system in gliding and turning, was simple in control and facile in practice. based on frenet frame, the linear time - variable error equations of parafoil system were built

    基於frenet系推導和建立了翼傘系統線性時不變的誤差方程,並運用「投影點」的思想來獲得frenet系下偏差量的解析表達式,從而設計了用於翼傘系統航跡跟蹤的傳統pd控制器和增益調節型模糊pd控制器。
  3. In this article, an equivalent definition of reconstruct function is drew in the state space reconstruct by time delay chaotic time series, that lead the prediction more conveniently. then introduce a weighted distance to depict neighbour points of prediction which insured the similarity of the neighbour points

    本文在時間序列延遲后重構的相間中,作出重構函數的等價定義,提高了預測的可操作性;並在此基礎上,引入了加權距離來刻畫預測向量的鄰點,保證了鄰點的相性。
  4. Based on the nonlinear parabolic approximate wave reflection - diffraction equation of mild slope, a model of wave propagation on a fan - shaped coordinate is put forward considering winds, bottom friction and wave breaking, etc. the existing calculation shows that the model can be employed to determine wave fields in large water areas

    接著以非線性的拋物型波浪緩坡方程為基礎,提出了扇形下的波浪傳播模型,模型包括了風、底摩阻、波浪破碎等因素的影響,可以用於大水域的波浪場的確定;文章最後介紹了一些計算算例。
  5. Secondly, the problem of the curve - surface mutual transforming and smooth - finishing have been analyzed farther. for the surface intersecting problem : owing to the introduction of the boundary points, as long as the intersecting points on a certain line, the full intersecting line can be gained. the intersecting line either intersects at the boundary of the triangle surface or forms the loop ; during the course of tracking, the selecting of the pace is restricted by the curvature, the number of the gained intersecting points are not in proportion as the chord - length ; the intersecting points not only record the coordinate and store the parameter

    對兩曲面求交問題,當曲面細化足夠小時,曲面求交可看成曲面與平面相交問題,引進了邊界點的概念,因此只要知道交線上的任意點,就可以將跨越許多曲面片的整條交線計算出來,所求出的交線或者跨越曲面的邊界,或者形成交線環;從初始點出發跟蹤求解整條交線的過程中,步長的選擇採用了通過曲面片曲率來約束的方法,用該方法求出的交點在不同曲面片上的分佈數目不與弦長成正比;該求交方法包含了各曲面片的邊界線與交線的交點的求解,可獲得邊界交點的值及其參數值。
  6. In chapter six, we studied the nonlinear solitary wave solution under the transverse perturbations for a system of coupled nonlinear electrical transmission lines. in the continuum limit and suitably scaled coordinates, the voltage on the system is described by a modified zakharov - kuznetsov equation

    論文第六章研究了耦合非線性傳輸線系統中的孤波,在連續和合適的系下, 11一一一一一一藕合非線性傳輸系統的電壓可以用mzk方程( 。
  7. Then a suboptimal solution of the graph maximum equal - cut problem is presented employing the randomized algorithm and the improved coordinate ascent ( descent ) algorithm on the optimal solution of semidefmite relaxation

    在利用lagrange乘子理論得出原始問題的等價形式之後,將演算法與改進的上升(下降)演算法結合,求得原問題的次優解。
  8. Parallex bump mapping is a new technology to archive the target that renders wrinkle surface of high quality with a relatively low cost. it uses a much smart way that offsets the surface ' s texture coordinates than the ordinary displacement bump mapping technology that offsets the surface ' s geometry vertex instead. we will propose a bulk of idea to improve this technology ' s performance and quality

    視差紋理映射技術是新提出的實現物體表面粗糙感的一種凹凸映射技術,它是對目前因計算量過大而無法應用於實時渲染系統中的位移映射技術的改進,這種技術不是對物體表面的頂點進行偏移,而是藉助于高度圖對紋理進行偏移,從而達到位移映射技術的效果。
  9. In this thesis, we for the first time corrected the thrust axis to qq direction using mc simulation, and in this way eliminated the systematic errors coming from the difference in thrust and qq directions

    通常是地選取沖度軸為縱(主)軸方向。本文首次採用mc模擬產生的數據,將實驗結果從沖度軸修正到q (
分享友人