退火周期 的英文怎麼說
中文拼音 [tuìhuǒzhōuqī]
退火周期
英文
annealing cycle-
Besides, scan rate and cycle period also affect the result ; co - deposition of dualistic oxide is a focus of research, as an element in the same group, ir is selected. deposition rate of composition is decreased by the adding of ir composition, and when the proportion of ir exceeded 50 %, composition procession can be ceased. but cooperation of ir and ru oxide can highly increase the specific capacitance of active material ; annealing treatment under a certain temperature can help to change the hydrate ru composition into mixture state ru oxide, accordingly increase the stabilization of active material
研究表明:電解液的配製過程中，氯化釕濃度、溶液ph值、陳化時間、溶液溫度對電鍍效果均有影響，其中溶液ph值是最主要的影響因素;在儀器的使用條件探索中，理論結合實驗確定了本電鍍液體系循環伏安電勢窗的理想范圍，並發現循環伏安掃描速度和掃描周期對電鍍結果也有較大影響;混合氧化物的共沉澱是目前研究熱點，在此選用與釕同一族的銥作為共沉澱元素，銥的加入會阻礙氧化物的沉積速度，銥的比例超過50 %會使沉積作用停止，但是二元氧化物的協同作用使沉積的活性物質比容量大大提高;一定溫度下退火后處理作用會使水合釕化物轉變成混合價態的氧化釕，從而提高活性物質的穩定性。The results demonstrate that the upper limit of permafrost in this area had declined from 1970s to the middle phase of 1990, and permafrost has appeared degenerate tendecy, but since middle 1990s, permafrost have a stable state ; ground temperature of roadbed near the earth surface is higher than that of the natural ground, thawing time of roadbed near the earth surface is longer than that of the natural ground, the heat income within the permafrost is greater than the heat release from the permafrost during anannual period, the heat accumulation within the permafrost is temporarily appeared as temperature rising, but with the heat accumulation within permafrost growing up year by year, permafrost temperature will become higher gradually, and strong thawing of permafrost could be happened in the region
結果表明：風火山地區從20世紀70年代到90年代中期凍土上限下降，凍土出現退化現象，從90年代至今凍土趨于穩定；路基近地表地溫明顯高於對應天然地表下的地溫，路基近地表經歷的融化期長于對應天然地表，進入多年凍土區的熱收支也呈現出吸熱明顯大於放熱的周期性變化，進入多年凍土的熱積累暫時以增高地溫耗熱為主，但隨著凍土吸熱量的逐年積累、凍土溫度的不斷升高，本區凍土可能發生強烈融化。This, on the one hand, greatly obstructs the automation, and on the other, makes it very hard for the green hand to master. as a result, the technique is now meeting with the problem of handing down. the key to the problem is to quantify in a pragmatic way the effect that different factors have on plate shaping
隨著科技的發展，由於水火彎板加工的經驗性及手工操作，使得外板彎曲成形加工成為影響船體建造周期與實現自動化的瓶頸；而且隨著老工人的退休，而青年工人掌握這項工藝又需相當長的時間，導致水火彎板技術青黃不接的現象日趨嚴重。Optimum ductility is obtained with a ferritic matrix, therefore, all nibco ' s ductile iron pressure containing parts are treated with a ferritizing annealing cycle
通過鐵素體基體可獲得最佳的展延性，因此，所有美國尼伯科球墨鑄鐵的壓力負載部件都經過鐵素體化退火周期的工藝處理。分享友人