速動錘 的英文怎麼說
中文拼音 [sùdòngchuí]
速動錘
英文
rapid action hammer-
The single - stage hammer crusher are suitable used to crushing ordinary fragile ores of the compressive strength no more than 200mpa, such as limestone, gypsum, coal, marl, sand - shale etc. this series product features of high crushing ratio, even product graininess, simple construction, reliable operation, easily maintenance, economical running cost etc., so are widely used. hammer crusher models hammer crusher max
錘破系經高速轉動的錘體與物料碰撞面破碎物料,錘式破碎機具有結構簡單,破碎比大,生產效率高等特點,錘式破碎機可作干濕兩種形式破碎,錘式破碎機適用於礦山水泥煤炭冶金建材公路燃化等部門對中等硬度及脆性物料進行細碎。A synchronous motor drives the measuring bob at a constant rotational speed.
同步馬達驅動測錘以恆速旋轉。The effect of variation in surge shaft section size upon the reflection of water hammer pressure and the speed of quality fluctuation attenuation
調壓井斷面尺寸變化對水錘壓力反射及質量波動衰減速度的影響The optimum design of the beat back - impact crusher is proposed, which aims at the highest efficiency of the machine work. the optimum designed mathematics model of the main structural dimension of the crusher ( m, xc, s, w 2 > ir ) is built with restraining conditions such as force condition, energy condition, hammer steady condition, no moving interference, strength of spin axle and bearing condition, upper limit and lower limit of the design variant condition etc. finally, an example is give to illustrate the efficiently of the method proposed
在綜合考慮影響破碎機效率的各因素的情況下,提出了滿足以力,能量,錘頭穩定性,幾何條件,不發生運動干涉,轉子軸和滾動軸承的強度等約束條件,建立了包含破碎機關鍵參數(錘頭質量m ,軸心o到銷軸錘頭接觸距離r ' ,四川大學碩士學位論文錘頭質心到銷軸與錘頭接觸點的距離拙,錘頭與巖石碰撞到銷軸與錘頭接觸點的距離s ,轉子的速度。3 transmission, built in the top drive power head, has two speed range ? high and low. it can meet the requirements of both dth hammer drilling and carbide bit drilling
3動力頭設有變速裝置,有高低兩個檔次,以滿足潛孔錘鉆進及硬質合金回轉鉆進方法。This machine is of hammer type high speed crusher, material is fed into the crushing chamber by a hopper through screw conveyor and crushed by high speed rotating hammer, the crushed material is entered into the catcher automatically under the effect of rotating centrifugal force, and the dust is filtered and recovered by dust collector through a bag
本機為錘式高速粉碎機,物料由料斗經螺旋輸送桿進入粉碎室,被高速旋轉的錘子擊碎,而獲得粉碎,粉碎好的物料經旋轉離心力的作用,自動進入捕集袋,粉塵由吸塵箱經布袋過濾回收。By using the soil samples prepared with different dry density and water content, a great amount of instant vibration test is performed and the signals of acceleration and force are acquired
在實驗室內對製作成一定密實度的試樣進行了大量瞬態振動測試,獲得試樣在錘擊作用下的加速度和力信號。Power bond graph is used to established the bond graph model of the lifting and dropping of hydraulic pile hammer and state space equation in the paper for hydraulic pile hammer is perplexing nonlinear system. in order to attain the graph that pressure, position, velocity, acceleration vary with time in the course of driving pile simulation procedure solving state space equation is designed on the basis of combining four - order runge - kutta method with predicator - corrector method, dynamic simulation of the hydraulic system is studied in matlab 6. 5. it is convenient to analyse dynamic characteristics of the hydraulic syste m, beneficial to the design and parameter optimization of the hydraulic system. in the final part of the paper, under detailed analysis of the control characteristics for double - acting hydraulic pile hammer with double cylinders, control system based on the programmable logic controllers founded on technology of modern compute is designed
由於液壓打樁錘液壓系統是一個復雜的非線性系統,本文採用功率鍵合圖法建立液壓打樁錘上行、下降的鍵合圖模型和狀態空間方程,通過四階龍格?庫塔法和預估?校正法相結合編制了模擬程序對狀態空間方程求解,在matlab6 . 5中進行液壓系統的動態模擬,獲得液壓打樁錘運動過程中壓力、位移、速度、加速度等隨時間變化的曲線圖。此曲線圖方便了對液壓系統動態特性分析,為液壓系統的設計和參數優化提供了有益的借鑒。最後,在深入分析雙缸雙作用液壓打樁錘控制系統的功能要求后,採用了以現代計算機技術為基礎的新型工業控制裝置? plc可編程式控制制器,設計出了雙缸雙作用液壓打樁錘的電器控制系統。Quick closing valves, water hammer or supply pressure fluctuations can cause intermittent discharge
迅速關閉閥門,水錘或供應壓力波動可能導致間歇性排放。When the suspended point is moving on the line in a kind of way, the pendulum will depart from the balance position. in order to minimize the swing movement of pendulum and minimize the consumption of power, a linear regulator is created for the system. finally, a optimum feed back status of speed is made
當懸掛點以某種規律沿直線運動時,會出現擺錘偏離原太原理工大學碩士研究生畢業論文平衡位置的情況,為了使擺錘在給定時間內在懸掛點行走一定距離的過程中擺角最小且能耗最少,本文將系統構造成為線性調節器,最終得到了使懸掛點移動速度最優的狀態反饋量分享友人