連接線誤差 的英文怎麼說
中文拼音 [liánjiēxiànwùchā]
連接線誤差
英文
connecting wire error- 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
- 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
- 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
- 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
- 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
- 連接線 : connecting wire
- 連接 : connect; fit together; link; marry; mate; joint; association trail; linkage; concatenate; concate...
- 誤差 : error
-
This paper selects dc double - arm bridge, uses the four - port connection to remove the contact and connection resistances and reduce the electromagnetism interfere. grounding grid conductors fault levels are established during a lot of emulational computations, simulative experiments
使用直流雙臂電橋，採用四端鈕連接法，可大大降低現場中電磁干擾及引線電阻和接觸電阻的誤差影響。Because of the unique issues in the networks, including mobility - induced disconnection, network partition, high out - of - order delivery ratios and channel errors, the congestion control and the error recovery in the network is challenging. in this environment, the interaction between tcp and mac layer protocols, the affection of route protocols on the performance of tcp and the particular congestion control and error recovery mechanism are first discussed. then a particular transport layer protocol scheme based on the non - feedback mechanism is presented, with emphasis on the analysis and simulation of the key parameter
文中主要討論了兩種不同網路結構中的無線tcp協議改進方案，其一在最後一跳為無線鏈路的網路環境中，針對基本tcp擁塞控制機制存在的缺陷，文中在現有解決方案的基礎上提出一綜合性的方案，其中包括無線鏈路的高誤碼率和連接斷開問題的解決，並重點對方案中出現的交叉層問題進行分析和模擬；其二，考慮的是分散式網路（ adhoc ） ，在文中較為詳細的分析了tcp和mac層機制間的相互作用、路由協議中造成tcp性能降低的因素、 adhoc網路中應採取的特殊擁塞控制和差錯恢復機制，在此基礎上提出了一種採用非反饋機制的解決方案，重點對方案中的關鍵參數進行分析和模擬，分析和模擬結果表明此機制可在很大程度上提高adhoc網路中tcp的性能。Furthermore, the current research about body measuring and modeling is just for costume and military affairs, and pay more attention to the head dimension and shape. with the development of human nature during the manufacturing, body cad model is widely applied in industry design, ergonomics, engineering design, humanics research and iatrology research. the body cad model also can be the basic data for the design of respirator
本文使用nurbs曲面直接擬合的方法對測量的點雲進行曲面重構，將系統的優化方法應用到nurbs曲面重構中，利用插值曲線對測量點雲進行分塊處理，解決用nurbs曲面擬合中曲面的光順與曲面與點雲的誤差之間的矛盾問題，使反求模型中各曲面片之間相互連接、光順過渡且能夠反映出人體頭部的細部特徵。With different clearance value, displacement curves and velocity curves of generalized coordinates as well as slider displacement error curves in a motion period are obtained. these curves are discussed. results show that if manufacturing cost is kept invariableness, in order to improve precision of mould - cuting, fitting precision of joint connecting the crank and coupler has priority to be considered to increase
採用四階rong - kuta法求解連續接觸模型的動力學方程，得到了一個運動周期內運動副間隙取不同值時，各廣義坐標的位移、速度曲線和滑塊位移誤差曲線，並通過曲線分析，得出了要提高模切機主切機構精度，在相同加工成本條件下，應優先考慮提高曲柄與連桿鉸接處的配合精度的結論。A linear programming method of vector loop used in the analysis of mechanism motion and its error was introduced, the possibility of using the sensitivity of kinematic analysis for error was analyzed, and it was proposed for the error analysis model of the mechanism to make equivalent substitution for the dimensional error with basic kinematic joint element ( kinematic pair ) and as well to implement the linear programming method of vector loop for error analysis within the adams
摘要介紹機構運動分析與誤差分析的向量環路線性規劃法，分析運用運動分析靈敏度進行誤差分析的可能性，提出在機構誤差分析模型中用基本運動連接元素（運動副）對尺寸誤差進行等價替換，使誤差分析向量環路線性規劃法在adams中實現。Feedrate planning of continuous micro - line ' s start and end points are discussed, and the constraining conditions, including the machine ' s acceleration and deceleration capability, allowable error of corner machining, maximum acceleration and dynamical behavior of the machine, are established 。
摘要針對連續小直線段高速高精插補演算法中起始點和終止點的速度規劃，建立了包含機床加減速性能、轉接處誤差控制、最大加速度以及機床負載功率等的速度約束條件。Connecting wire error
連接線誤差分享友人