連桿曲線 的英文怎麼說

中文拼音 [liángǎnqūxiàn]
連桿曲線 英文
coupler-curve
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 桿 : 桿名詞（桿子） pole; staff
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 連桿 : [機械工程] link; connecting rod; perch; go between; column; connecting bar; crank guide; link lev...
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  1. The main work includes : the kinematic properties of a planner 4 - bar linkage are researched deeply using the assur group theory. the displacement, velocity and acceleration of each joint point in a motion period are put forward and their curves of the relevant points are plotted

    通過運動學分析，得出平面連桿機構在一個運動周期中各鉸接點的位置、速度和加速度以及各桿件的角速度、角加速度等運動學參數，並繪制出相應的變化曲線。
  2. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  3. The paper studied relations between academic inertial force graph in ellipse and experimental inertial force graph in " the 8 shape ", presented the inertial force experimental method through shifting cylinder in a testing bed on by a angle every time, the obtained graph and data represent inertial force principal parameters

    摘要討論了曲柄連桿機構的理論慣性力曲線（力橢圓）和實驗慣性力曲線（力8字）的關系，提出在擺架上逐點偏移汽缸進行慣性力實驗的方法，得到的實驗慣性力曲線完全反映了慣性力的主要參數。
  4. The model considers the torsional deformation of transmission axes, bending and longitudinal deformation of links, geometrical nonlinearity of guiding leaf springs, and the elastic nonlinearity of balance springs

    該模型考慮了傳動軸的扭轉變形，連桿和導向板彈簧的彎曲和拉伸變形，導向板彈簧的幾何非線性及平衡彈簧的非線性等因素的影響。
  5. According to the special stratum condition 、 soil parameter 、 pile frame system in the protecting landslide of hongtian jianfeng in yongan city in fujian province, compile a fem program of plane strain and analyze the interaction by nonlinear fem on intensity discount. in the program, duncan - chang model is applied to earth, elasticity model is applied to pile and rock ; goodman element is set between pile and rock - earth and applied to simulate sliding plane and flexible floor ; sequential pole elements with original stress are applied to anchor cable

    在程序中土體採用了duncan - chang雙曲線本構模型，樁和錨固層以下的巖體採用了線彈性本構模型，並且在樁和巖土體間設置了無厚度的古德曼（ goodman ）單元，對于軟弱夾層和已知的滑裂面也採用古德曼單元模擬，錨索採用的是具有初始應力的連續桿單元模擬。
  6. In the paper, based on the method of low pair replacing with high pair, the problem of cam design was transferred to that of linkage design. by means of rotary unit vectors, the equations of displacement, velocity and acceleration of the replacement mechanisms were developed. and then, the virtual linkage ' s length and direction were deduced

    論文基於高副低代原理，將平面凸輪機構設計與再現函數的平面連桿機構設計統一為同一種方法，運用圓向量函數建立代換機構的位移、速度、加速度矢量方程式，求取虛擬連桿桿長和方向，由此展開凸輪理論廓線、實際廓線、曲率半徑和壓力角的求解，並得出用圓形刀具加工凸輪時刀具中心的軌跡方程。
  7. ( 4 ) the running state and hydraulic property of the hydraulic automatic tilting gate with connecting lever and rolling wheel were analyzed. the open - door curve, start - up water level and shutdown water level were ascertained, then the influence of lower reaches of a river to the running of a tilting gate was analyzed

    （ 4 ）析闡述了連桿滾輪式水力自動翻板閘門的工作狀態與水力特性，推求了閘門的開門曲線、啟門水位和回關水位，並分析了下游水位對翻板閘門運行的影響。
  8. With different clearance value, displacement curves and velocity curves of generalized coordinates as well as slider displacement error curves in a motion period are obtained. these curves are discussed. results show that if manufacturing cost is kept invariableness, in order to improve precision of mould - cuting, fitting precision of joint connecting the crank and coupler has priority to be considered to increase

    採用四階rong - kuta法求解連續接觸模型的動力學方程，得到了一個運動周期內運動副間隙取不同值時，各廣義坐標的位移、速度曲線和滑塊位移誤差曲線，並通過曲線分析，得出了要提高模切機主切機構精度，在相同加工成本條件下，應優先考慮提高曲柄與連桿鉸接處的配合精度的結論。
  9. Then the center ' s track equation of the circular cutter which was used to manufacture the cam was presented. for the problem of designing on combined cam mechanism which follows the given track, typical nodes in the track were selected at first. then the spline interpolation method was employed to plot the smooth track

    針對實現特定軌跡的凸輪一連桿組合機構設計問題，文中首先選取軌跡上有代表性的節點，採用樣條插值法繪出光滑的軌跡曲線，進而具體分析從動件的位移、類速度、類加速度，最後對凸輪-連桿組合機構進行設計。
  10. A kinematic chain portion composed of two linkages and three lower pairs are taken as primary cell and classified into different schemes

    摘要給出了機構基元的定義，提出了連桿機構工程語義的描述方法，實現了基於工程語義的機構軌跡曲線方程的演算法。
  11. The curve needes to realize is discretized as input, and computed by support vector machine, then the right type curve can be recognized

    提出一種基於支持向聖機的連桿曲線識別方法，把所要實現的軌跡離散化作為輸入，通過所設計的支持向量機的判別，找到圖譜中相對應的軌跡曲線。
  12. There are too many curves in pattern of bar linkage curves, how to find the right curve is the key for applications of pattern. a method based on support vector machine to recognize bar linkage curve is presented in this paper

    摘要四連桿機構的軌跡圖譜相當繁浩，如何從數千條軌跡曲線中找到與要求實現的軌跡相同或相似的圖形是限制軌跡圖譜應用的關鍵之一。
  13. Considering joint clearances at both ends of the coupler, a continuous contact model is developed by modeling clearance as a massless rigid link. a set of strongly nonlinear equations is obtained by using angle displacement of clearances in kinematic pairs as generalized coordinates. four order rong - kutta method is adopted to solve the dynamical equations of continuous contact model

    考慮曲柄與連桿、連桿與滑塊之間運動副間隙，將運動副間隙看成是一無質量的理想桿，利用連續接觸模型進行建模，採用運動副間隙角作為廣義坐標，得出一組強非線性方程組。
  14. Contrastive tests of damping aluminum - alloys, zinc - alloys and 45 # steel are carried out at the case of equal stiffness. the test results show that when the rocker bar is made of damping aluminum - alloys or damping zinc - alloys, the strain amplitude at the middle point of connecting bar is half of the one when the rocker bar is made of 45 # steel

    在等剛度條件下對鋁基、鋅基阻尼合金和45鋼阻尼減振作川進行了對比實驗，實驗結果表明搖桿為鋁基和鋅基阻尼合金材料時，連桿中點動態應變曲線幅值只有45鋼時的一半左右，而且隨著曲柄轉速的提高，阻尼合金的減振效果更加明顯。
  15. This paper introduces the method of functional approaching method analysis of the four - combined - poll installation in order to approximately achieve the given curve lines

    摘要本文用函數逼近法綜合鉸鏈四桿機構，使其近似實現給定的連桿曲線。
  16. Presents a new method of path mechanism synthesis which is based on coupler - angle curves moment invariant and is an improvement on the path synthesis method of planar linkage by coupler - angle curves

    摘要提出了一種新的軌跡機構綜合方法，該方法對利用連桿轉角曲線綜合軌跡機構方法作了較大的改進，提出基於連桿轉角曲線不變矩的軌跡機構綜合的神經網路方法。
分享友人
分享到 Line

分享到臉書