連續拉伸 的英文怎麼說

中文拼音 [liánxùlāshēn]
連續拉伸 英文
continuous drawing
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 續 : Ⅰ形容詞（連接不斷） continuous; successive Ⅱ動詞1 （接在原有的后頭） continue; extend; join 2 （...
  • 拉 : 拉構詞成分。
  • 伸 : Ⅰ動詞（展開） stretch; extend Ⅱ名詞（姓氏） a surname
  • 連續 : continuation; succession; series; continuity; continuing; running; continuous; successive; contin...
  1. Continuous hot - dip aluminium silicon - coated cold - reduced carbon steel sheet of commercial and drawing qualities

    商業和拉伸質量用連續熱浸鋁硅鍍層碳素鋼薄板材
  2. An interface analysis model was established based on the interface stress element method for discontinuous medium mechanical problem to simulate the pull - out tests and tensile tests, and the calculated results are in good agreement with those of experiments

    應用解決不連續介質力學問題的界面應力元法建立交界面的分析模型，對拔出試驗和拉伸試驗進行了數值模擬，數值模擬計算結果與試驗結果接近。
  3. With the aid of the obtained fundamental solutions and the continuity conditions of stress and displacement on material interface, complex potentials solutions for an bi - material infinite plate with an elliptical inclusion under pulling stress are given

    根據界面上應力和位移的連續條件，得到了單向拉伸狀態下，含有橢圓夾雜的無限大雙材料組合板的復勢解。
  4. Also the regulations of stain and resistivity of smart composite with additives of continuous carbon fiber and graphite are analyzed

    本文還對連續碳纖維、鱗片填料在拉伸狀態下應變與體積電阻率之間的變化關系進行了研究和分析。
  5. Nanocrack might nucleate at a crack tip or in the dfz. in the thicker area, a ribbon thin area or a zigzag thin area might be formed by slip

    金屬薄膜拉伸過程中，微裂紋可以在主裂紋頂端連續形核擴展，也可以在無位錯區中不連續形核擴展。
  6. Textile machinery and accessories - cylindrical tubes - part 5 : dimensions. tolerances and designation of tubes for continuous spin - drawn synthetic filament yarns iso 3914 - 5 : 1994

    紡織機械和附件.圓柱形紗管.第5部分:連續紡絲拉伸合
  7. The stress - strain curves are different from macroscale situation. varied strain rates have different effects to nanometer material deformation. compared with macroscale, nanoscale mechanical behaviour of bending is dissimilarity

    拉伸作用下的應力應變曲線變化趨勢並不與宏觀介質連續力學下完全相同，不同的應變率會對材料變形造成不同的影響。
  8. Standard practice for constant - amplitude, axial, tension - tension cyclic fatigue of continuous fiber - reinforced advanced ceramics at ambient temperatures

    室溫下連續纖維增強高級陶瓷的等高度軸向的和雙向拉伸循環疲勞強度的標準規程
  9. Standard test method for tensile breaking strength of perforations in one - part continuous forms paper

    一部分連續式紙張孔眼的拉伸斷裂強度的標準試驗方法
  10. Based on the hot tensile test results, there exists a cooling rate at which a minimum reduction in area occurs and the hot ductility of the sn - doped steel is worse than that of the sn - undoped steel. when the cooling rate is lower or higher than 10 / s, the hot ductility is increased

    連續冷卻到750 800范圍內拉伸時，存在一個冷卻速率（ 10 s ） ，以這個冷卻速率進行冷卻，試樣的斷面收縮率最小，熱塑性最差；當冷卻速率大於或者小於這個冷卻速率時，試樣的斷面收縮率均會增大，熱塑性增強。
  11. Tensile performance of unidirectional continuous bamboo fiber reinforced polymer composite

    單向連續竹纖維增強聚合物的拉伸性能
  12. Testing methods for tensile stress - strain behavior of continuous fiber reinforced ceramic matrix composites at room temperature

    室溫下連續纖維增強陶瓷基質復合材料的拉伸應力應變性能的測試方法
分享友人
分享到 Line

分享到臉書