連續拉拔 的英文怎麼說

中文拼音 [liánxùlābá]
連續拉拔 英文
continuous drawing
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 續 : Ⅰ形容詞（連接不斷） continuous; successive Ⅱ動詞1 （接在原有的后頭） continue; extend; join 2 （...
  • 拉 : 拉構詞成分。
  • 拔 : Ⅰ動詞1 （拉出; 抽出） pluck; pull out; pull up; draw; move 2 （吸出） draw; suck out 3 （選取 提...
  • 連續 : continuation; succession; series; continuity; continuing; running; continuous; successive; contin...
  • 拉拔 : [冶金學] draft; drawing拉拔力 pulling capacity; 拉拔模孔 draw hole; 拉拔強度 pull strength; 拉拔...
  1. With double travelling cranes, advanced 60mm punching machine, 140mm fungus type punching machine ; domestic leading 159mma r tube rolling - mills, 159mm7 rack calibrator ; the national monopoly product micro tension - reducing diameter machinery and the producer gas generator ; 40, 60, 80, 220mm straightening machine ; 5 40 tons motoblocs ; bottom rolling type continual annealing furnace ; 14m pitch type heating furnace as well as qg1118 highly effective pipe cutter and so on as well as correlated necessary facility

    公司據有雙配行車的大型廠房17500平方米，先進的60mm穿孔機， 140mm菌式穿孔機國內領先的159mmar軋管機， 159mm7機架定徑機國家專利產品微張力減徑機和煤氣發生爐40 60 80 220mm矯直機540噸拉拔機滾底式連續退火爐14m斜坡式加熱爐以及qg1118高效切管機等以及相關配套設施。
  2. An interface analysis model was established based on the interface stress element method for discontinuous medium mechanical problem to simulate the pull - out tests and tensile tests, and the calculated results are in good agreement with those of experiments

    應用解決不連續介質力學問題的界面應力元法建立交界面的分析模型，對拔出試驗和拉伸試驗進行了數值模擬，數值模擬計算結果與試驗結果接近。
  3. Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly

    摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。
  4. Three factors, such as pull - up type, the materials and structure of crystallizing mould, and the temperature field in crystallizing mould, influencing on continuous up - casting for aluminum were analyzed, which laid the foundation of the application to continuous up - casting technology for aluminum bar

    分析研究了引拔拉坯制式、結晶模材料及結構、結晶模內溫度場三因素對鋁上引連鑄的影響規律，結果表明上引連續鑄造過程中施加適當頻率的反推和反推量有利於桿坯連鑄的持續，結晶模自身的性能及模內溫度場的狀態對金屬鋁桿上引連鑄工藝的實現有直接影響。
分享友人
分享到 Line

分享到臉書