進料分佈板 的英文怎麼說
中文拼音 [jìnliàofēnbùbǎn]
進料分佈板
英文
feed distributing plate-
The contents include : based on the previous research and the data of experimentations, the author researches and develops a kind of satisfactory semi - empirical formula of nonlinear temperature distribution, and calculates the temperature stress of rigid - framed arch bridge by the fem. the temperature effects of bridge structure by annual and sunlight temperature difference are discussed, it indicates that the temperature effect of annual temperature difference is small but the temperature effect of sunlight temperature difference is great and the temperature stress along beam depth resulted from sunlight temperature difference is nonlinear. with the comparison between the temperature effects of different position of bridge, the results show that where the section of bridge is small, the temperature stress of it is large
本文主要包括以下內容：從理論上研究並結合實測資料發展了一種比較理想的半經驗溫度場非線性分佈公式，並將有限元方法應用於剛架拱橋結構溫度應力的計算中，對橋梁結構進行整體溫度應力分析；討論了年溫差和日照溫差引起的橋梁結構的溫度效應，表明年溫差引起的溫度效應較小，而日照溫差引起的溫度應力較大且沿梁高呈非線性分佈；分析比較了橋梁結構各個部位的溫度效應的大小，可知截面越小溫度拉應力越大，受力越不利；並對箱梁結構由於構造不同引起的縱向與橫向的溫度效應大小進行了探討，發現在頂板下緣也會出現相當大的溫度拉應力，並且梗腋的存在反而增加了頂板底部的溫度拉應力；還對幾種相近的剛構式橋型的溫度效應進行了分析對比，總結了這些橋型針對溫度效應的優劣，並提出相應的針對性措施。The hydrodynamics of slurry bubble columns with and without a perforated plate distributor have been investigated with a coal solid concentration of 29 % ( wt ) under a continuous operation mode for both liquid and solid
摘要對于有、無進料口多孔板分佈器兩種結構下淤漿床中的流動特性進行了考察。Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle ， 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got
對雙金屬復合板成型過程進行模擬，從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律，復合后的齒形的變形情況與初始齒形形成對比，以動畫的方式模擬成型過程，並分析了不同幾何參數（主要是不同的齒型，其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型） 、材料參數、工藝參數對復合強度的影響，以及不同齒型的變形對比以及齒型對復合情況的影響，提出最優齒型、最優工藝參數，有效地指導了實驗。The results indicate that the position of sensitive plates is located at the section of middle or upper in tower but not near by feeding plate, and the smaller reflux ratio, the closer overhead of distillation tower. accurate calculation for flash is solved using matlab, and the result is correct and reasonable. complicated multi - components distillation and crude distillation are simulated using chemcad, and results are reasonable about profiles of flow for vapor and liquid as well as temperature in the tower
數值分析的結果表明精餾塔靈敏板位置並不在進料板附近，而是位於精餾段的中上部，且迴流比愈小，愈靠近塔頂;利用matlab實現了蒸餾過程的嚴格計算，與參考值比較，結果正確、合理;藉助于chemcad進行常減壓塔的穩態模擬計算，得出了流量和溫度在塔內的分佈，經過理論分析，結果合理，可為實際生產提供參考。Cylindrical bending of functionally graded plates with arbitrary distributions of material properties under arbitrary loading are studied using hybrid differential quadrature method ( hdqm )
摘要利用混合微分求積法，對任意荷載作用下不同材料梯度分佈的功能梯度材料平板柱形彎曲問題進行了分析。Experiment data is analyzed with method of projection pursuit for more reliability and utility value. this paper first systematically studied energy dissipater of suspension girder in steep gradient with supercritical flow according to used in actual engineering and received perfect effect. experimental studies about the distribution velocity, the variation of water surface and pressure are undertaken
然而，文章主要針對已獲國家自然科學基金資助，且已在實際工程實踐中產生了良好消能效果的陡坡急流懸柵消能工的部分試驗成果，進行了較全面深入地討論，即具體根據試驗資料系統分析了懸柵陡槽內泄水時的流速分佈、底板壓力分佈及水面線變化情況。Aiming at reducing the roughness of the sidewalls in the manufacturing of the pmma liquid pool by co _ 2 lasers, in the hypothesis that the intensity of the laser has a guassian distribution, the temperature distribution in slab material with limited thickness is studied according to traditional thermal conductive formulas, and the condensing progress of the melted surface of sidewalls is researched. it is concluded from the discussion of temperature distribution that the air bulbs is the major reason for the roughness of the sidewalls
為降低co _ 2激光加工pmma材料儲液池側壁粗糙度，本文根據傳統的熱傳導方程，假定激光強度為高斯分佈，對有限厚板狀材料的溫度場進行分析;並考察側壁表面熔化層凝固過程的特徵;結果表明，側壁粗糙度形成的主要原因在於側壁表面熔化層凝固前氣泡未及時析出。A material nonlinear finite element analysis for the cast - in - place reinforced concrete hollow slab that occurs from initial loading, cracking, yielding to failing is carried on. the cracking load, ultimate load, the displacement rules and the principal stress distribution rules of the hollow slab under the vertical loads are obtained. a material nonlinear finite element analysis for the single span hollow flat - plate floor is also carried on
其次對空心板進行了從加荷、開裂、屈服直至破壞的全過程材料非線性有限元計算，得到了空心板在豎向荷載作用下的開裂荷載、極限荷載及位移和應力分佈規律；還對單跨無梁樓蓋進行了材料非線性有限元計算，通過分析主應力場明確了柱上暗扁梁的作用；有限元計算的結果驗證了以上的理論分析並得到了一些重要的結論，對改進現澆空心板無梁樓蓋的構造措施有重要的參考價值。2. in this thesis, the mesoporous silica was experimented by using macromolecule microemulsion as template, and template was removed through calcinations and extraction with hot ethanol. the mesoporous materials were synthesized and characterized with tem, x - ray diffraction, nitrogen adsorption / desorption and ft - ir techniques, etc. the results showed that all the samples had larger porediameter than samples " through calcinations under resembled conditions, but the mesopore ordered poorly
首先以剛合成的粒徑均勻分佈的高分子微乳液為模板劑和反應介質，採用萃取和煅燒的方法得到了介孔氧化硅材料，採用ft - ir 、 xrd 、 tem 、 n _ 2吸附脫附曲線等測試手段對經不同處理過的介孔氧化硅材料結構進行了表徵。And in coordination with data obtained from an engineering test on site, the regularities of foundation settlement and the distribution properties of pile reaction, soil reaction and steel stress in raft, of the pile - ( thick ) raft tested are analyzed. in the same time, the calculating results with finite element method almost correspond with measured results
另外，通過對一超高層建築樁（厚）筏基礎進行原位實測，取得了比較完備的實測資料，分析了基礎沉降的特點和樁頂反力、樁間土反力和筏板鋼筋應力的分佈特點和規律，同時用有限元法進行了近似計算，與實測結果基本吻合。( 1 ) car body stands in quite identical stress level by decreasing the thickness of plates, ameliorating structure and so on in strength affluence position under five cases ; ( 2 ) without changing stress distribution, holes are dug in bearing the weight of positions by wiped off material in order to decrease weight
（ 1 ）在強度富裕處通過降低板厚、改進結構等手段，使得整車在強度規范的五種工況下，各處均處于較為相當一致的應力水平； （ 2 ）在各種承載部位，在不改變其應力分佈的前提下開設減重孔，利用去除材料來達到減重的目的。分享友人