進氣余面 的英文怎麼說

中文拼音 [jìnqìyúmiàn]
進氣余面 英文
outside lap
  • 進 : 進構詞成分。
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 進氣 : air admission; admission; inlet; onflow; charging; access of air; admittance; air in; air intake;...
  • 余面 : lap
  1. 3. on boiler retrofit, the calculation of fuel burning, the heat calculation of boiler inside structure and convection section, and the design of structure parameter of feed water heat exchanger are made. the flue gas channels " resistance calculation and the boiler strength verifying are also carried out. replacement of water cooling wall improves heat exchanging and decreases loss of heat radiant

    對鍋爐本體進行了燃料燃燒計算、爐膛結構熱力計算、對流受熱面結構熱力計算、鍋爐給水加熱器結構參數設計、煙道阻力計算及鍋爐元件強度校核等；改進了水冷壁布置使換熱效果更好，減少輻射換熱損失；改進對流段結構，更充分的利用爐膛出口煙氣余熱，提高熱效率；並且進行了煙氣阻力計算、熱效率計算和能量平衡測試，對改進后的稠油燃料和改進前進行了對比，燃燒狀況和熱效率有明顯改善。
  2. In chapter 5, the principle of molten carbonate fuel cell power system is introduced. the development of the system, such as the improvement of cell components including electrodes and electrolyte, the fuel processing, the heat recovery, the power conditioning and grid interconnection, the control system and the combine generation

    第五章在簡要敘述了熔融碳酸鹽燃料電池發電系統原理后，從以下幾個方面對系統的開發進行了論證:單體元件（電極和電解質）性能的提高，燃料的處理，余熱利用，電力調節和並網，燃料電池/燃氣輪機/汽輪機聯合發電以及系統控制與優化。
  3. The pertinence of actualizing the measures is particular, which requires the status of remaining heating and cooling load, building utility, meteorological data, etc. should synthetically be taken into consideration

    但節能技術措施的實施具有較強的針對性，需要綜合無余熱負荷（冷負荷） 、建築功能、氣象參數等多方面的因素進行綜合考慮。
  4. The changing procedure includes : extending of the blade on the tip, extending of the blade on the root, expanding of the surfaces of the blade, extending of the blade on both sides, calculating the balance angle, changing the coordinate system, changing the data on the consideration of the shrinking and the reflecting of the blade material, etc. a blade surface is bended and distorted in three dimensions

    具體轉化過程包括：葉尖型面延伸、葉根型面延伸、葉身型面余量加放、進排氣邊余量加放、平衡角的計算、考慮葉片的收縮和回彈、坐標轉換等。完成了葉身實體造型。葉身型面是復雜三維彎扭曲面，造型上既有精度要求又有光順性要求。
分享友人
分享到 Line

分享到臉書