進汽壓力 的英文怎麼說

中文拼音 [jìnqìyālì]
進汽壓力 英文
admission pressure
  • 進 : 進構詞成分。
  • 汽 : 名詞1. （由液體或某些固體變成的氣體） vapour2. （水蒸氣） steam
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  1. In chapter 2, the meteorological knowledge, data and the methods of the data processing, related to the study on the atmospheric loads, are simply presented. the model for the perfect gas constant, describes by the relative moisture, is developed. the influences of the variation in the vapor component in the atmosphere on the perfect gas constant are evaluated by using the changing characteristics of the temperature on the surface, its spatial gradient and the barometric pressure

    第二章：簡要介紹大氣負荷研究所需的氣象科學知識、資料及其數據處理方法；建立相對濕度表示的大氣比氣體常數模型，利用地面溫度和空間垂直溫度梯度、壓力變化的規律估算大氣水汽組分變化對比氣體常數的影響；對中國及鄰區的地面氣壓記錄進行了預處理和網格化
  2. The paper studies the degradation rule of physical mechanical property of vulcanizate during the period of heat ageing, which involves the relationship between the property, variable temperature and time. the analytic expressions for the frictional temperature rise of the interface were presented according to the theory of heat conduction of solid when a tire slides of rolls along the road. finally, the value of temperature and pressure is used to monitor the tire ' s status

    本課題針對影響汽車輪胎橡膠機械性能的溫度老化模型進行了一定深度的理論研究，並進一步研究輪胎的在滑動、滾動時的溫度場的數學模型，在理論上論證了溫度、壓力是影響輪胎行使安全性能的重要因素，並以其作為最終的監測對象。
  3. The main steam pressure control system, bed temperature measure system, bed temperature adjust system and action condition of ham fuel trip ( mft ) are analyzed

    對主蒸汽壓力控制系統、床溫側量系統、床溫校正系統和主燃料跳閘的動作條件進行了詳細的分析。
  4. Yaojung shiao and john j. moskwa, “ cylinder pressure and combustion heat release estimation for si engine diagnostic using nonlinear sliding observers ”, ieee trans. vol3, no1, 1995

    陳建霖，汽油引擎進氣壓力及點火角度對引擎性能影響之電腦模擬，碩士論文，雲林科技大學，雲林， 2003 。
  5. The " green " bricks are then treated in an autoclave under steam pressure forming hydrated calcium silicate bonding the aggregate particles into a strong and durable brick

    然後該綠色磚在一個高壓鍋的蒸汽壓力下進行處理，形成水化硅酸鈣再結合聚合物顆粒的堅固耐用的磚塊多孔磚和加氣
  6. The relations between soil surface resistance and evaporating time, and difference of vapour pressure between evaporating plane and atmosphere were simulated. simulating result of the latter was better than that of the former

    同時，還對土壤表面阻力與蒸發時間的關系、與蒸發時間及土壤蒸發面和大氣間水汽壓差的關系進行了模擬，結果后一種比前一種模擬更符合實際。
  7. The bubbles in diesel engine fuel injection system are studied. the frequency structure of pressure wave with bubbles bursting ， as well as relation of types of bubbles and frequency spectrum ， is expounded

    採用頻譜分析法對柴油機燃油噴射系統中的汽泡進行了研究，分析了汽泡潰滅造成壓力波振蕩的頻率結構特性，並論述了汽泡與壓力波及其頻譜的關系。
  8. The first one is based on approximating the measured vapor pressure decrease by least square method, then inserting this approximation into the ideal gas equation to get ammonia absorption rate

    一種方法是基於理想氣體方程。首先，對實驗中測量到的壓力降曲線用最小二乘法進行處理，將處理后的數據代入理想氣體方程，從而求得氨蒸汽的吸收量。
  9. The inlet steam pressure shall not exceed 110 percent of maximum pressure in maintaining these averages, except during abnormal conditions

    ?譯為：進汽壓力不得超過12個月運行期內的最大壓力。
  10. This paper develops a whole - course alarm unit for pulsing vacuum high - pressure steam sterilization to monitor hydraulic pressure, vacuumizing ability, sterile time, sterile pressure and drying time. the unit alarms if any parameter mentioned above is out of order

    現特設計一種滅菌全過程監測的報警裝置，可對水源壓力、高壓蒸汽滅菌器真空度、滅菌器夾層壓力、滅菌器內室壓力及計時進行實時監測，當任一程序在使用中出現異常時，報警裝置將發出準確部位的報警信號，提醒工作人員及時排除故障，保障滅菌效果。
  11. The stress is basing coal - fired boiler inflammation system feature and control demand to design a kind of fuzzy - pi controller on based of genetic algorithm to control it. the controller refers the error and its variety rate as its inputs. and, in order to make the control qualities much better, concerns them as the performance index to optimize the membership function of the fuzzy variables and the pi ' s controller parameter by means of online adjujsting the genetic algorithm, inflammation system steam pressure loop and economic inflammation loop

    重點是針對燃煤鍋爐燃燒系統的特點和控制要求，設計了一種基於遺傳演算法的模糊- pi復合控制器對其進行控制，該控制器以偏差、偏差變化率作為輸入量，通過遺傳演算法在線調整模糊控制器的模糊變量隸屬度函數和pi控制器的參數，從而達到優化模糊控制規則和pi控制器參數的目的，實現燃燒系統的蒸汽壓力迴路和經濟燃燒迴路的控制要求。
  12. With the combination of automatic control theory and practical thermal process automation object in the power station, three main fields including nonlinear calibration of thermal instrument, new control strategies of main steam pressure and advanced control strategies of main steam temperature are studied in detail in this paper

    本文將自動控制理論和火電廠熱工自動化的具體對象相結合，進行了3個方面的研究工作：熱工儀表非線性校正、主蒸汽壓力的新型調節策略、主蒸汽溫度的先進控制策略。
  13. In order to complete the research on optimal control regular for coal - fired boiler inflammation system. in this paper, a type of coal - fired boiler inflammation system is regarded as the research target, after separately analyzed steam pressure loop and economical inflammation loop, we obtained the relevant control scheme, and designed a kind of fuzzy - pi compound controller on based of genetic algorithm to control two loops, and using genetic algorithm tool kit below the matlab progressed system simulation research

    為了完成對燃煤鍋爐燃燒系統的最優控制規律的研究，本文以某型燃煤鍋爐的燃燒系統作為研究對象，分別對其蒸汽壓力迴路和經濟燃燒迴路進行系統分析，得到了相應的控制方案，設計了一種基於遺傳演算法的模糊- pi復合控制器對該系統進行控制，並用matlab下的遺傳演算法工具箱進行了系統模擬研究。
  14. The experiment took water as the medium and experiments on two jet modes were carried out under the falling film vacuum evaporating. the experimental results indicated that the two ejectors in series compensation method could adjust the variational work situation due to the decrease of primary steam or secondary steam and insure the normal production. at the same time, the ejector ' s best work situation founded in the experiment would provide reference for ejector ' s design and usage

    本實驗建立了一套降膜真空蒸發裝置，以水為介質，對變工況下單級和串聯噴射熱泵蒸發進行了實驗，結果表明兩級串聯補償噴射裝置能對由引射蒸汽和工組蒸汽壓力降低所造成的混合蒸汽壓力降低進行調節，達到了變工況下正常生產的目的。
  15. Stability of main steam pressure is the foundation of the key parameter stability ( include the main steam temperature, the vapor pack water level, the oxygen content in the smoke etc. ) in the units, deb system increase the dependability and the economy greatly with the settlement of the energy ' s equilibrium between the boiler and the steamer

    本機組利用先進的硬體設備dcs和優化的控制策略deb ，圓滿解決了機組協調控制系統中主汽壓力穩定性及負荷適應性這一主要矛盾。主蒸汽壓力穩定是機組一切關鍵參數（包括主蒸汽溫度、汽包水位、煙氣含氧量等）穩定的基礎， deb系統解決了機組鍋爐和汽輪機之間能量平衡，使機組可靠性和經濟性大大提高。
  16. There will be a hot water layer in the water of cmt when vapour spews to uppercooling water surface vertically and coagulates directly. the higher of the vapour pressure of prz and the initial water temperature of cmt are, the deeper the hot water layer is. and obtaining the experience formula of the hot water layer is as follows : the condensation coefficient is high when vapour coagulate at first, then it will lessen with the process of coagulation, the higher of the vapour pressure of prz and the initial water temperature of cmt are, the higher of condensation coefficient is

    蒸汽垂直噴入過冷水表面凝結時， cmt中水有明顯熱分層現象， prz中飽和蒸汽壓力越高， cmt中水初始溫度越高，熱分層厚度越大，熱分層厚度的經驗關聯式為：凝結剛開始時，凝結換熱系數非常大， ，隨著凝結的進行，凝結換熱系數越來越小， prz中飽和蒸汽壓力越高， cmt中水初始溫度越高，凝結換熱系數越大。
  17. This article emphatically discussed and analyzed following points : load command feed forward function can improve the rapid respond character of steam turbine generator ; lead of load command have advance control function on boiler main control and can highly improve the stability of main steam pressure ; the use of predict control and state space variable function can improve the quality of boiler steam temperature control effectively, control the steam temperature in the defined range and increase the boiler and turbine life and efficiency even if working state changed in a big range ; linear compensation can restrain the vibration of generator load in the condition of big loa d change

    本文重點討論、分析提出負荷指令前饋作用可以提高汽輪發電機快速響應特性；負荷指令的導前功能對鍋爐主控有超前控製作用，能顯著提高主蒸汽壓力的穩定性；採用預測及狀態空間法能有效改進鍋爐蒸汽溫度控製品質，在大幅度工況變化下仍有效控制蒸汽溫度在額定范圍內，提高鍋爐、汽輪機壽命及其效率；汽輪發電機組的快速響應性與汽輪發電機組負荷振蕩問題間的平衡關系，採用線性補償可以有效抑制在負荷變化梯度較大情況下發電機負荷振蕩問題。
  18. The condensation heat - exchange characteristic of a separate - type heat - pipe was studied on a 1 : 1 model. the heat pipe is heated by electricity, and working fluid is distilled water, and it is cooled by air. the experimental results show that, ( 1 ) when charging liquid ratio is 45 %, condensation heat - exchange coefficient reaches to maxium ; ( 2 ) when there is not non - condensing gas, the coeffcient decreases a little with the increase of vapour pressure, and it decreases by 9. 5 % when the pressure increases from 0. 16mpa to 0. 36mpa ; ( 3 ) when there is non - condensing gas, the coefficient decreases a little, but when the gas is discharged by an exhaust value, it can be improved, when the volume content of the gas is 2. 5 %, it can increased by 22 % ; ( 4 ) the effect of the non - condensing gas on the coefficient decreases with the increase of the pressure, and when the volume content of the gas is 5 % and the pressure increases from 0. 16mpa to 0. 36mpa, the coefficient increases by 6 %. the relative curves are given between condensation heat - exchange coefficient and air flowrate, charging liquid ratio and vapour pressure

    建立了空氣冷卻實驗臺，熱管的加熱方式為電加熱，工質為蒸餾水.在1 1模型上對分離式熱管管內凝結換熱特性、不凝性氣體對凝結換熱的影響及不凝性氣體的擴散規律進行了試驗，得出分離式熱管有一最佳充液率，其值為45 %左右；凝結換熱系數隨著蒸汽壓力的增加略有降低，在實驗的壓力范圍內，降低了9 . 5 % ；不凝性氣體對分離式熱管的凝結換熱僅影響冷凝段下部較小部分，通過排氣閥排出不凝性氣體可有效地改善冷凝段下部的凝結換熱；隨著壓力的增加，不凝性氣體對分離式熱管冷凝段的影響減少.這些結論可用於分離式熱管換熱器的工程設計和控制
  19. Abstract : the condensation heat - exchange characteristic of a separate - type heat - pipe was studied on a 1 : 1 model. the heat pipe is heated by electricity, and working fluid is distilled water, and it is cooled by air. the experimental results show that, ( 1 ) when charging liquid ratio is 45 %, condensation heat - exchange coefficient reaches to maxium ; ( 2 ) when there is not non - condensing gas, the coeffcient decreases a little with the increase of vapour pressure, and it decreases by 9. 5 % when the pressure increases from 0. 16mpa to 0. 36mpa ; ( 3 ) when there is non - condensing gas, the coefficient decreases a little, but when the gas is discharged by an exhaust value, it can be improved, when the volume content of the gas is 2. 5 %, it can increased by 22 % ; ( 4 ) the effect of the non - condensing gas on the coefficient decreases with the increase of the pressure, and when the volume content of the gas is 5 % and the pressure increases from 0. 16mpa to 0. 36mpa, the coefficient increases by 6 %. the relative curves are given between condensation heat - exchange coefficient and air flowrate, charging liquid ratio and vapour pressure

    文摘:建立了空氣冷卻實驗臺，熱管的加熱方式為電加熱，工質為蒸餾水.在1 1模型上對分離式熱管管內凝結換熱特性、不凝性氣體對凝結換熱的影響及不凝性氣體的擴散規律進行了試驗，得出分離式熱管有一最佳充液率，其值為45 %左右；凝結換熱系數隨著蒸汽壓力的增加略有降低，在實驗的壓力范圍內，降低了9 . 5 % ；不凝性氣體對分離式熱管的凝結換熱僅影響冷凝段下部較小部分，通過排氣閥排出不凝性氣體可有效地改善冷凝段下部的凝結換熱；隨著壓力的增加，不凝性氣體對分離式熱管冷凝段的影響減少.這些結論可用於分離式熱管換熱器的工程設計和控制
  20. The interactions between heat flux density, vapor pressure, vapor velocity and the coefficient of heat transfer for condensation in tube, the coefficient of heat transfer in total are investigated. the relationships between heat flux density and the total difference in temperature, the difference of temperature, pressure drop of vapor from the entrance of the tube to the exit are investigated as well

    考察了冷卻水流量、溫度恆定條件下熱流密度、蒸汽壓力、蒸汽流速對冷凝傳熱膜系數及總傳熱系數的影響關系，同時考察了總傳熱溫差、蒸汽進出口溫差及壓差隨熱流密度變化的關系。
分享友人
分享到 Line

分享到臉書