進油泵 的英文怎麼說

中文拼音 [jìnyóubèng]
進油泵 英文
inlet pump
  • 進 : 進構詞成分。
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 泵 : 名詞（吸入和排出流體的機械） pump
  1. This article compares the fuelling process between the typical self - suction pump and modern immersible pump - based fuelling in fuelling stations

    摘要介紹了傳統加油站採用自吸泵型加油機的加油工藝和近年來採用潛油泵加油機的加油工藝，並進行了對比。
  2. It is pointed out that the immersible pump - based fuelling process can realize the multi oil gun on the one pump basis under the condition of positive pressure, which makes the design of fuelling station more flexible and is a development tendency in modern fuelling station

    指出採用自吸泵型加油機的加油工藝存在弊端，而採用潛油泵加油機的加油工藝，可以實現一泵多槍，油罐正壓出油，技術先進，工藝簡單，使加油站設計更加靈活，是現代化新型加油站的技術發展趨勢。
  3. According to the above theories, with using the software - deform - 3d, we have made the numerical analog simulation and analyse the warm extrusion forming technique process for sway oil pump stator, optimized the forming : technique and the die parameter for the pockety wall thickness forging this paper concretely analysis and research metal flow ' s characterize in different forming processes

    本課題根據上述理論，利用有限元數值模擬模擬軟體deform - 3d ，對轉向油泵定子溫擠成形工藝過程進行模擬模擬分析，優化了油泵定子的成形工藝及模具參數。
  4. In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production

    論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。
  5. Cyz - a self - priming centrifugal oil pump according to domestic and international to develop newest pump products that become after digesting, absorbing, improving about technical data by oneself, domestic blank, unique, extensively suitable for the oil depot, service station, oil ship, oil carrier, quay, oil truck, airport, send the petrol, kerosene, diesel oil, boat coal etc

    型自吸式離心油泵是根據國內外有關技術資料經消化、吸收、改進后研製而成的最新泵類產品，國內空白獨一無二，該泵適用於石油行業、陸地油庫、油灌車的理想產品，並適合於作船底泵、消防泵和壓載泵及機器冷卻水循環等，分別輸送汽油、煤油、柴油、航煤等石油產品和海水、清水，介質溫度- 20 80 ，加輸送化工液體可改用耐腐蝕機械密封。
  6. Hydraulic concrete crusher detail : all round, extremely efficient concrete crusher system for concrete demolition in general, and reinforcement exposure in particular. the system works immissionfree, i. e. : it does not produce any noise, dust or cibrations and operates without water. description : pliers qty 1, hydraulic power pack qty 1, 10m long oil pipe set of hoses, high pression qty 2, accessories bag qty 1

    啟動電機帶動油泵運轉，液壓油直接返回油箱手動轉動換向閥三位四通閥一個位置后，液壓油進入系統推動活塞，活塞桿伸出，帶動鉗體收縮，從而破碎鋼筋混凝土結構，反向轉動換向閥，鉗體松開，完成一個工作循環。
  7. Abstract : a new model of sand - control and wear - resistance pump is developed based on conventional deep well pump through improving some not - suitable construction and processing technology

    文摘:防砂耐磨抽油泵是在傳統管式深井泵的基礎上，對某些不太合理的結構和加工工藝進行了改進和優化。
  8. The vacuum-relief valve opens to allow enough air to enter the tank to replace the gasoline pumped from the tank by the fuel pump.

    真空閥通向大氣，使足夠的空氣進入油箱，以補充由輸油泵從油箱中吸出的燃油所佔的面積。
  9. - 2 - several mechanical problems of enter - material pump which occurred in recent years in dushanzi petroleum and petrochemical industry are introduced and diagnosed. these examples show that vibration diagnosis is of great significance

    本論文針對獨山子石化總公司煉油廠焦化車間的輻射進料泵的實際故障進行了診斷，這也正是研究振動診斷技術的真正意義。
  10. A method based on the application of an injection process analysis software is introduced in this article, which optimize injection process through changing the design of fuel - injection pump cam. a model of 1115 single cylinder direct injection diesel engine is used as an example. with the help of pre - journey optimization, increasing cam lift and using tangent - function can make the matching of the injection system with the diesel more reasonable. without changing fuel pump installing size, it can enhance injection rate and injection pressure and improve the diesel operating stability in low speed condition

    本文以國產1115型單缸直噴柴油機為例，介紹一種應用噴油過程分析軟體改進噴油泵凸輪設計的方法，通過增大噴油泵凸輪升程、採用切線函數凸輪並優化預行程的方式，在不改變噴油泵安裝尺寸的前提下，可提高噴油壓力和噴油速率，改善柴油機低速工作穩定性，使噴油系統與柴油機匹配更合理。
  11. At an early stage in the evolution of the high - speed diesel a variable timing device was introduced in the pump drive coupling, taking the form of a helically splined coupling by means of which the angular relation between driving and driven shafts could be varied by manual or automatic control

    翻譯：在高速柴油機發展的早期，可變的正時裝置被引用到油泵驅動聯軸節上，採用螺旋式花鍵套管的形狀，驅動軸和從動軸之間的相對角度可以通過手動或自動控制進行改變。
  12. From the above it will be realised that fundamental difference between petrol and diesel engines is that in the petrol engine the source of heat for igniting the charge, namely an electric spark, is generated outside the engine, and is taken, as it were, into the waiting charge at the required instant

    翻譯：在高速柴油機發展的早期，可變的正時裝置被引用到油泵驅動聯軸節上，採用螺旋式花鍵套管的形狀，驅動軸和從動軸之間的相對角度可以通過手動或自動控制進行改變。
  13. A series of tests on centrifugal oil pumps with different specific speeds were done under different conditions of liquid viscosities and pump rotary speeds

    摘要用比轉速為66 ， 90 ， 105的離心泵在不同粘度、不同轉速下進行了一系列試驗，提出了一種新的油泵液體粘度換算方法，該方法考慮了轉速對換算系數的影響。
  14. The company uses the low pressure casting in producing such as gasoline pump body, cylinder head, moto cylinder head and so on other aluminum alloy casting products, which has yearly capability of 3 million aluminum alloy castings and 200, 000 pcs finished products output, and is continuously evaluated as " advanced unit on quality ", " the excellent supplier ", " the high - quality

    公司採用低壓鑄造生產汽車油泵體氣缸蓋摩托氣缸蓋等鋁合金鑄件產品，具有年產300萬件鋁合金鑄件的能力。公司連續多年被主機廠評為「質量先進單位」 「優秀供應商」 「優質服務獎」 。
  15. The suitable oil flux during the circulating of transformer could be defined according to the difference of temperature between the oil and wind in the inlet and the cooling capacity of the wind cooling system ; besides the oil flux can be determined by ultrasonic, it can be estimated whether the oil is flowing equably by determining the oil flux in the branch pipes ; reducing the oil flux of the oil pump could be realized by controlling to change its frequency, which could not only save the energy, reduce the wastage, but benefit the transformer ' s circulating safely

    變壓器運行中可根據進口油溫和進口風溫之差、風冷卻器的冷卻容量來確定合適的油流量；油流量可以通過超聲波法進行測量，測量油的分管流量還可判斷油流的均勻情況；降低潛油泵流量可通過潛油泵的變頻控制來實現，不僅節能降耗，對變壓器的安全運行也有著重要意義。
  16. We imported lots of advanced equipments like robot welding machine, cnc pipe bending machine etc from japan, italy and other countries. our annual output reached 800, 000 sets of exhaust catalytic converters, 500, 000 sets of mufflers, 1. 5 million pieces of m2 luxury wall bricks. our products get a come out top position in our markets, meanwhile we act as oem for motorola, simens, the united electronics and china automobile group

    我公司自行研製的汽車電子燃油泵已批量生產，與國際合作開發的汽車電子油門踏板總成及陶瓷加熱元件屬于填補國內空缺並達到國際先進水平的高新技術產品。
  17. Discharge coefficient is the important factor of influencing sucker rod pump performance. the discharge coefficient is calculated, and the main influencing factors are analyzed

    本文對有桿抽油泵的排量系數進行了詳細的計算，系統地分析了影響排量系數的主要因素。
  18. Combining with practical application, the factors that influence sucker rod pump performance are studied in this dissertation

    本文結合工程實際，對影響有桿抽油泵性能的因素進行了比較深入的研究。
  19. Thirdly, geometry modeling of the pump was made and meshes were divided with gimbit, then the flow filed was investigated using flunt, a commercial available cfd code. as result, lots of internal flow filed of outlet of the gear pump was obtained, including velocity magnitude and pressure magnitude

    應用pro / e和gambit軟體對機油泵進行幾何建模並劃分網格，應用fluent軟體模擬多種工況下機油泵出口部分的三維湍流流動，得到詳盡的三維湍流場的分析結果，包括壓力分布圖、速度矢量分布圖等。
  20. Chapter 3 gives an introduction to the flow rate dividing principle based on meter - in flow rate feedback control of multi - actuators control system. special analysis about simultaneously operating multi - actuators with different inertia loads is made. finally the results of simulation proved that the new method is an effective way to improve the flow - used ratio when the pump discharge flow rate is insufficient

    第三章介紹了基於執行器進油側流量反饋的分流控制的原理，並針對大小慣性執行器同時起動時採用該分流控制方法進行了具體分析；最後通過模擬說明該分流控制方法能在大小慣性執行器同時起動並在泵輸出流量不足的情況下有效提高泵輸出流量的利用率，並能實現優先級和分流比混合控制。
分享友人
分享到 Line

分享到臉書