過度功率 的英文怎麼說

中文拼音 [guòdùgōnglǜ]
過度功率 英文
overpower
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 功 : 名詞1 （功勞） exploit; merit; meritorious service [deed]: 戰功 military exploits; 立功 render me...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 過度 : excessive; over; undue; ana-; hyper-
  1. Due to existing signal processing technology ’ s shortage such aslow measurement, narrow measurement range precision and other poor performance, we introduced a high - precise signal processing technology : firstly, to get power spectrum with hanning windowed welch modified periodogram, search its peak value frequency ; secondly, to apply zooming analysis via goertzel algorithm ; at last, to get a highly precise doppler frequency with energy centrobaric rectifying algorithm 。 the simulating result indicated that this technology introduced could get accurate doppler frequency 。 depending on above discussed technology, we designed a signal processing scheme, and developed a signal processing system. the running result showed high performance, verified the feasibility and reliability of the highly precise signal processing technology introduced. in a word, the technology improved ldv ’ s performance such as measurement precision, measurement range, dynamic response time 。 and it will have a wide application foreground

    針對存在的缺點，本文提出了一種應用於激光多普勒測速的高精度信號處理技術，即首先利用加hanning窗的welch修正周期圖演算法得到信號功率譜，搜索其譜峰值頻率，接著利用goertzel頻譜細化演算法對搜索的譜峰進行細化分析，再引入能量重心頻譜校正演算法對細化后的譜峰進行校正分析，從而將離散頻譜分析演算法、頻譜細化演算法和頻譜校正演算法三者有機結合起來，充分發揮各自的優點:通過加hanning窗的welch修正周期圖演算法快速得到功率譜及峰值頻率，通過goertzel演算法獲得分析頻帶的高解析度頻譜，然後通過能量重心校正演算法對細化后的頻譜進行高精度校正，這樣不僅保證了演算法的高效性，而且大大提高了分析的精度。
  2. The cumulation of tdfcsd in a certain period eliminates the remainder noise more, and the ability of detecting signal ' s frequency is improved

    通過對某段時間得到的功率譜密度累積，進一步改善snr ，提高信號頻率的檢測能力。
  3. Secondly, output powers are measured in the different wind velocity or the direction angle or angle speed for mechanics model. the optimal angle of the direction is determined. that is to say, output power is the maximum in this direction angle

    其次，通過對風力發電機模型在不同風速、不同方向角、不同角速度的情況下輸出功率的測量，得出最佳方向角，即在該方向角處輸出功率最大。
  4. Under simple development, it could be applied on active - matrix oled directly. finally we design power circuit, through the design of a stable current circuit, we solve the disaffiliate luminance in oled

    另外，還設計了後端的功率電路，通過對恆流源電路的設計很好的解決了顯示屏亮度不均勻的問題。
  5. This paper explains the effective encouraging mechanism of electrovalence at present, analyses the close relationship between the primary transformer capacity for electric power using in the enterprise and the basic electricity expenses and the electricity in peak time, the relationship between the power factor and the electricity expenses per degree. the ways and measures of reducing electric cost and decreasing electricity expenses expenditurze are proposed

    通過闡述現行電價政策的有效激勵機制，分析了企業用電主變壓器容量與基本電費和峰谷分時用電及企業功率因數與電度電費的密切聯系，提出了企業降低用電成本、減少電費支出的途徑和措施。
  6. The experimental results show : the flattop phenomenon on the diode voltage pulse was very apparent for using the carbon fiber cathode, that is to say, the pulse duration of the diode voltage was widened ; moreover, under the condition of the same power of microwave, the pulse duration of the out - put microwave was prolonged by about 30 % ; the peak power of the microwave was enhanced by 3db

    通過在裝置上做的兩種陰極的對比實驗，結果顯示:碳纖維陰極的使用，改善了電子束質量，使輻射微波的脈寬增加了30 %以上，輻射主瓣方向上的功率密度提高了3db以上，頻譜分佈較純凈，實現了微波的高效輸出。
  7. The high - power semiconductor quantum well ( qw ) laser is a kind of luminescence device with superior performance, it has longe - lived, low threshold current density, high efficiency, high luminosity and excellent monochromatic, coherence, directionality, etc. the high - power semiconductor laser is widely applied to the fields, such as military, industrial machining, communication, information processing, medical treatment, etc. the material ' s epitaxy is the foundation of the whole laser ' s fabricating, and it has important influence on the optics and electricity performance about the laser

    大功率半導體量子阱激光器是一種性能優越的發光器件，具有壽命長、閾值電流密度低、效率高、亮度高以及良好的單色性、相干性、方向性等特點，廣泛應用於軍事、工業加工、通信及信息處理、醫療保健等領域。材料的外延生長是整個激光器器件製作的基礎，對器件的光學和電學性能有著重要的影響，生長不出優質的材料體系，獲得高性能的器件就無從談起，因此，材料的外延生長便成為了整個半導體激光器製作過程之中的重中之重。
  8. The effect of cutting speed, cutting thickness, cutting knife and materials on the working power capacity is discussed. finally tractive property of road plane milling machine is also studied. through the comparison of the results of theory calculation and experimental results the equation of working power capacity of milling machine is modified

    本文對冷式瀝青路面銑刨機的動力學工作過程進行了理論分析與試驗研究，並利用金屬材料切削的基本原理，研究了主切削力，並從能量轉化守恆的角度推導了銑刨機銑刨作業阻力和功率計算公式，討論了機器切削速度、銑刨厚度以及刀具與材料特性對銑刨作業阻力和功率的影響規律，最後討論了銑刨機牽引性能，且通過試驗研究驗證了銑刨作業阻力和功率公式。
  9. It is designed according to electrical stove or microwave oven request. heating pipe adopts high temperature resistance mgo powder as the insulation medium and the stainless steel case is passed oxidation deal through the advanced web band protection oven 1050c in order to become the a special oxidation layer and improve the high temperature oxidation and bittern corrosive performance of the heating pipe. the heating tube has high power density and strong heat radion. this product with good safe performance can work normally after 3000hrs life test

    加熱管選用耐高溫氧化鎂作絕緣介質，不銹鋼外殼經過先進的網帶氣體保護爐1050的氧化處理，形成一種特殊的氧化層，提高電熱管的抗高溫氧化及鹽鹵的腐蝕性能。電熱管的功率密度較高，熱輻射能力強。產品經長達3000h的壽命試驗后，仍能正常工作，安全性能好。
  10. Based on the analysis of the effect on the maximum range of the equation ' s each parameter and the traditional method of extinction ratio, the noncooperative regulable attenuation - measure the minimum detectable power of laser altimeter on the condition of constant miss probability by attenuating the laser power transmitting to the diffuse reflected simulant target - was put forward

    在傳統的消光系數法基礎上，根據對月測距方程各系數的影響權重分析，提出了非合作目標可調衰減法，即：通過對漫反射模擬目標，衰減出射激光功率，在一定的漏警概率條件下測量激光高度計的最小可探測功率。
  11. Having studied the securities tax system in china, the paper puts forward that the current single tax system of stamp duty in securities market cannot guarantee the fiscal and cannot promote the market efficiency and social equity

    本文通過對中國證券稅制的制度功能進行反思，認為當前以證券交易印花銳為主體稅種的單一稅制不僅難以保證足夠的財政收入，更無助於增進市場效率和維護社會公平。
  12. The paper has founded the model of laser transmission in launch process and the movement model of laser - powered vehicle, and has analyzed the influence on performance of launch system, which was raised by some factors, for instance, the performance of thruster, the attenuation in transmission, the height of mode - transform, the laser power, the air drag force, the launch height, and so on

    本文研究了激光推進微小衛星發射系統的概念和性能。建立了發射過程激光傳輸和激光推進運載器運動模型，分析了推進系統性能、大氣傳輸衰減、模式轉換高度、激光器功率、大氣飛行阻力、發射點高度等因素對發射系統性能的影響。
  13. It is suitable to be used as the medium to filter the high purity and strong corrosive gas or liquid, the air plug of battery, gasket, seals for medium / low pressure, the waveguide tube pre - heater for boiler, the sealing wash, the cover of big - powered micro - wave antenna, and radar antenna of twt etc

    適用於過濾、高純度、強腐蝕性的氣體液體介質、蓄電池上作氣塞、襯墊、中低壓密封元件、鍋爐波管預熱器、密封圈和軍用微波大功率天線罩，以及行饋網路雷達天線等。
  14. The relation between area of ccd saturation and 0. 632 m 、 1. 06 m laser power / energy was measured. the ccd camera was disturbed by strong radiation from laser outside the field of view in experiment. the relation between the area of ccd saturation and off - axis angle was measured

    通過實驗，得到激光干擾ka - 320型面陣ccd光電探測器的像元飽和閾值、探測器靶面飽和閾值、局域損傷閾值，並得到了0 . 632 m與1 . 06 m波段入射激光功率與ccd靶面飽和程度的對應關系曲線，了解了面陣ccd探測器受激光干擾的各個階段。
  15. 1 m 0. 5, the phase - shifted angle 6 is controlled in term of sine law which makes the magnitude of resonant voltage track a reference sine voltage, and the resonant voltage is rectified, filtered, inverted and then the better sine - voltage output is obtained, theoretical analysis and experimental results show that for the resistive load and inductive load, the switches of leading leg of the phase - shift - controlled circuit are always turned on at zvs, and ones of lagging leg are turned on at zvs ( < 0 ) or turned off at zcs ( ( > 0 ), moreover, all switches in the low - frequency inverter are always turned on and off at zvs, the measured circuit efficiency for rated load reaches up to 88 %

    從功率單向流動角度出發，提出了一種lcc諧振型恆頻移相單相高頻鏈逆變電路拓撲，在調制系數0 . 1 m 0 . 5情況下，控制移相角按正弦規律變化，使諧振電壓脈沖列的幅值追蹤參考正弦電壓信號，經過整流、濾波、低頻逆變，從而獲得正弦度較好的輸出電壓。理論分析和實驗結果證明對于阻性負載或阻感性負載，移相全橋具有超前橋臂零電壓開通，滯后橋臂或者零電壓開通（ _ 0 ）或者零電流關斷（ _ 0 ）的軟開關特性，而低頻逆變器的各個開關均實現零電壓條件下的開通與關斷。
  16. When signals pass high power amplifier, they would be distorted in amplitude and phase, leading to spectrum spread and distortion of in - band signals, both of which would weaken performance of the whole system in turn

    在無線通信中，信號在通過高功率放大器時會產生幅度和相位失真，造成頻譜擴展以及帶內信號畸變，導致整個系統性能的降低。
  17. In the region of materials processing with high power diode laser array, people should couple the beam from diode laser with optical fibers in high efficiency

    本課題的目的是:通過大功率半導體激光器與光纖的雙向耦合，建立新型相干耦合的高光束質量大功率半導體激光器，以獲得高的焊接速度和良好的焊接質量。
  18. To solve it, the differential equation set is transformed by fourier transform and the dynamic differential equation in the form of matrix is educed. the calculation formulas of frequency response function of vehicle vibrating system, acceleration power spectrum density function are put forward

    用分析力學法建立整車動力學模型，推導出以矩陣形式表示的運動微分方程，並通過傅氏變換給出汽車動力學系統的頻率響應函數、加速度功率譜密度函數的計算公式。
  19. The random excitation of the four wheels is used as the input of this system. the changing rule of vertical displacement, three directions of acceleration power spectrum density function of person - chair system of model ca - 141 and etc. in the frequency domain is simulated using matlab. the rationality of the model is analyzed and validated by comparing of relevant testing results and theoretic analysis

    以頻域內四輪隨機激勵作為系統輸入，用matlab模擬低地板城市客車等三種車型人椅系統三向加速度功率譜的變化規律，逐項分析車速、懸架剛度與阻尼參數變化對車輛平順性的影響，通過與相關研究結果的比較及理論分析驗證了模型的合理性。
  20. In practice, it is currently very difficult to create a high - fidelity virtual reality experience, due largely to technical limitations on processing power, image resolution and communication bandwidth

    實踐中，產生一個高度保真虛擬現實體驗目前非常困難，主要由於處理過程功率、圖象解碼和通訊帶寬的技術限制。
分享友人
分享到 Line

分享到臉書