部分驅動脈沖 的英文怎麼說

中文拼音 [bùfēnqūdòngmàichōng]
部分驅動脈沖 英文
partial drive pluse
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 驅 : 動詞1. （趕） drive （a horse, car, etc. ） 2. （快跑） run quickly 3. （趕走） expel; disperse
  • 脈 : 脈名詞1. （動脈和靜脈的統稱） arteries and veins2. （脈搏的簡稱） pulse 3. （像血管的組織; 連貫成系統的東西） vein
  • 部分 : （整體中的局部或個體） part; section; portion
  1. Although there have been many application instances in the field of input / output device technology, we need an specific project and technology route aimed at an given application. in this thesis, we combine the introduction and analysis of relative technology to describe the accomplishment of a coordinate collecting device which is based on incremental rotary encoder. this device is an specific device applied to collect the corrdinate displacement of ground image ’ s three - dimensional model created by full digital photogrammetric station. cpld chip and vhdl are applied in this device to carry out the following work : phase control of the electrical pulse created by incremental rotary encoder, counting the number of electrical pulse, controling the state of signal processing circuit, exchanging data between this circuit and pci control

    本文結合相關技術的介紹和分析，描述了一個基於增量式旋轉編碼器的坐標參量採集介面卡的實現，此介面卡是一種用於採集全數字攝影測量系統地面影像模型坐標位移量的專用設備，該設備採用cpld器件和vhdl語言實現增量式旋轉編碼器的脈沖信號鑒相和計數、信號處理部分的狀態控制以及和pci總線晶元ch365之間的數據交換和通信功能，同時該設備的驅動程序基於wdm模式，並且配置有結構良好的動態鏈接庫程序作為系統軟體和驅動程序之間的數據和控制交互中間介面，能夠方便地運行在windows98 / 2000 / xp操作系統平臺上，具有實時性強、工作穩定、通用性較好和性價比高等特點。
  2. Partial drive pluse

    部分驅動脈沖
  3. In this paper, we design two types of flexible hinge, which are column stagger flexible hinge and flat straight round flexible hinge. the control system of the drive equipment includes the unity of the central console and control module. the console regards vc + + 6. 0 as the tool, it can set pulse number and pulse speed, start and stop the electromotor

    微驅動裝置的控制部分由上位機和控制模塊組成，上位機採用vc + + 6 . 0編制控制界面，可以設置電機旋轉所需的脈沖數和脈沖速度，可以實現電機的起停，正反轉及脈沖清零等工作，還可以分別控制不同鏡架的電機及相同鏡架的兩個電機。
  4. The paper describes a cw, non - cooling, digital all - solid - stated ld pumped nd : yvo4 driver which adopts microprocessor control, stability power of laser feedback and laser output power about 10mw. the system is composed of constant current source, soft diagram, protection, pulse schematic and laser power feedback loop. by combining appropriate hardware and software, we achieved, in our driver, a variety of protection features including the ability to suppress transients and reduce noise, relay soft and hardware over - current protection and overvoltage shut - off, we have obtained a continuously adjustable laser power output with high accuracy and stability

    介紹一種採用單片機控制的連續運轉無製冷、數字式光反饋穩功率全固態激光器驅動電源，其輸出激光功率在10mw左右，系統包括恆流源、保護電路、脈沖驅動控制、光反饋穩功率控制等部分，結合硬體及軟體實現了激光二極體的可靠保護以及光功率穩定、準確輸出及在穩光輸出情況下，實現激光器的內外調制，並取得了一些有價值的研究成果。
分享友人
分享到 Line

分享到臉書