酸液浸泡 的英文怎麼說
中文拼音 [suānyèjìnpāo]
酸液浸泡
英文
acid soak-
The physical methods include mechanical scarification, low and high temperature, hydration - dehydration, irradiation, high pressure and other physical treatments, and the chemical ones include acid scarification, alkali solution soaking and other organic chemical treatments
物理方法有機械損傷、低溫和高溫處理、干濕交錯處理、輻射和高壓處理等；化學方法有酸蝕、堿液浸泡和有機溶劑等處理。The effective regeneration procedure is soaking the adsorbent 30 ~ 50h with 1 - 2 % al2 ( so4 ) 3 for activated alumina and 20 ~ 30h with 1 - 1. 5 % naoh for bone char. studies show both activated alumina and bone char are excellent adsorbents for the removal of fluoride from drinking water. fluoride concentration below 1. 0mg / l can be acquired easily with them and meets the requirement of drinking water standards
對兩種除氟劑進行的再生液與吸附劑體積比為1 : 1的再生實驗表明：用硫酸鋁溶液對活性氧化鋁再生，再生濃度為1 2 ，再生時間為30 50h ，沖洗浸泡時間為5h效果較好；對骨炭再生，氫氧化鈉再生液濃度為1 1 . 5 ，再生時間為20 30h效果較好。Prepare the spotting slides soak the cover slides in chromic acid solution for more than 12hrs, wash to clean, soak in naoh, in acetone, in arm molecule solution for connecting, roast to fix the groups, ready for use
基片的處理和制備取蓋玻片，鉻酸洗液中浸泡過夜，洗凈， naoh浸泡，丙酮化，手臂分子連接，清洗，烘烤固定，醛基修飾。The pretreatment, effect of bath compositions and operation conditions such as temperature, currenty and time on compactness of the zinc and cu / ni / cr coatings have been investigated. the relationship of operation conditions to thickness of the coatings was studied by weight method. the specimens have been pickled in nacl or sulfate acid solution to evaluate the porosity of the coating
研究了鎂合金電鍍前處理工藝，電鍍鋅、電鍍銅/鎳/鉻工藝配方及其施鍍溫度、電流密度和時間對鍍層緻密性的影響;採用稱重法研究施鍍工藝與鍍層厚度的關系，利用nacl溶液和硫酸溶液浸泡試樣來考察鍍層孔隙率，採用劃痕試驗和熱震試驗檢驗鍍層的結合力，採用金相顯微鏡和掃描電子顯微鏡觀察鍍層表面形貌。Clinical effect of early exercise of patients with burn lesion after immersion in potassium permanganate solution
高錳酸鉀溶液浸泡對燒傷患者早期功能鍛煉效果的影響This article is about the polymer separator full of holes, we research the performance of the separator, including making two kinds separters that produce wth complete different methods : spreading the separator, pvdf as the basic material, dbp as the plasticizing agent, nm sio2 as the inorganic addition and acetone as the solvent, and make separator on the special machine ; dipping in the separator so that intensify the seprater, its dip liquor is as the liqure as the spreading separator, and dip the base material pp / pe / pp into the liquor for more than 2 hours
本文對多孔聚合物電解質隔膜進行了綜合研究。以聚偏氟乙烯（ pvdf ）為基體，鄰苯二甲酸二丁酯（ dbp ）為增塑劑，納米sio2為無機添加劑，丙酮為溶劑，在流延機上塗布得到了聚合物電解質隔膜。以流延法制備隔膜的漿料為處理液，將基體材料pp / pe / pp浸泡在處理液中2h以上，制備出強化電解質隔膜。The common method used by domestic and foreign scientists is removing the cobalt from the surface of the substrate by etching substrate using thin acid solution at room temperature. but the internal co will still overflow during mpcvd
為降低成核及成膜過程中鈷的副作用，國內外通常採用的方法是將硬質合金基體在室溫下用稀酸溶液浸泡一定時間，從而除去基體表面的鈷。分享友人