鋼板溫度 的英文怎麼說

中文拼音 [gāngbǎnwēndù]
鋼板溫度 英文
steel plate temperature
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 鋼板 : [冶金學]1 （板狀鋼材） steel plate; nickelclad steel sheet; plate 2 （汽車上的片狀彈簧） spring3 ...
  • 溫度 : [物理學] temperature
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. Ferritic - pearlitic steels for precipitation hardening from hot - working temperatures

    熱加工溫度下沉澱硬化用鐵素體-珠光體鋼板材
  3. Make the u type and w type heating tube to be series - wound and shunt - wound to meet the rated voltage reauest. the fixed housing is made adopting the stainless steel or high quality hot zincification board to resist high temperature and corrosive. matching the heat fuse and temperature controller to protect doubly the heating pipe of the air conditioner and keep safe. adopting the silicone rubber high temperature wire and imported connecting terminal to make the electric connection more fixed and reliable

    以達到額定功率的要求固定支架選用不銹鋼或優質鍍鋅板製作而成，耐溫防腐配用熱熔斷器和溫度控制器，對空調加熱管起著雙重熱保護作用，安全性能更好採用硅橡膠耐高溫線和進口接線插端，使產品電氣聯接緊固可靠。
  4. In this paper, a high performance sma system applied to steel bridge deck is put forth in allusion to the pavement project of the wuhan junshan yangtze river highway bridge. it comprises steel slab, zn coating layer, closing layer, adhesive, pre - mixed asphalt stone and dual layer sma from bottom to top. it is based on the fea results of the forces and deformation of the pavement layer by means of the algor feas, according to this bridge ' s traffic and the ambient temperature varying range of the pavement layer

    本文針對武漢軍山長江公路大橋鋼箱梁橋面鋪裝工程，從鋪裝層環境溫度變化范圍、交通量等使用條件出發，在用algorfeas有限元分析軟體分析鋪裝層受力變形基礎上，提出了（即鋼板+金屬鋅塗層+封閉層+粘接劑+預拌瀝青碎石+雙層sma ）的高性能鋼橋面sma鋪裝體系，並對這種sma的組成材料，包括改性瀝青、集料、礦粉、纖維進行了比較研究，設計了這種sma的配合比，對sma混合料的性能進行了對比試驗，對這種sma方案進行了疲勞性能研究，驗證了所選擇sma方案的可行性。
  5. In the paper, not only such factors as reinforcing steel bar, various placing temperature of concrete in case of lift placements, lift thickness, time interval between lifts, the variation of elastic modules of concrete, heat of hydration, the temperature changes of environment but the effect of creep deformation and autogenous volume change on the temperature field and thermal stress field of reinforced concrete face - slab are considered

    本論文在分析中，考慮了鋼筋、混凝土分層澆築、入倉溫度、澆築層厚、施工間歇、混凝土彈性模量變化、水化熱發散規律、外界氣溫等因素的變化及混凝土徐變和自生體積變形等因素對面板溫度場和溫度應力的影響。
  6. To avoid manual labor of chiseling - grossness, in the area of second - stage concrete construction, permanently non - removed metal molding boards nets are used as molding boards of first - stage concrete. substitution joints of reinforcing steel bars for traditional electric welding and usage of equipments for joints of reinforcing steel bars efficiently improve strength of junctions and rate of connecting reinforcing steel bars, and safety of construction and stability of quality, and greatly reduce cost. it ' s possible that three gorges project become top - ranking project in the world by study on systems engineering of high - strength concrete construction

    混凝土縫面處理採用高壓水流沖毛技術，大大提高了施工工效，減少了倉面污染；模板工程大量採用定型鋼模板施工技術，提高了壩體混凝土成型質量和工程進度；在二期混凝土施工區域，為免除人工鑿毛勞動強度，採用永久性免拆金屬模板網作為一期混凝土模板；鋼筋連接改進傳統的電焊連接方式，採用大量採用鋼筋接頭機械連接技術，有效提高了接頭強度和鋼筋連接速度，施工安全性大大加強，質量穩定性有效提高，經濟成本大大降低；三峽二期工程持續高強度混凝土施工系統工程的研究，使三峽工程成為名符其實的「世界一流工程」成為可能；三峽二期工程混凝土溫控綜合技術的應用，有效降低了壩體混凝土溫度的產生；混凝土表面處理及裂縫處理技術的應用，提高了建築物的整體性和耐久性。
  7. Diamond micro powder ( abrasive grain = 0. 5 u m ) is added to the plating liquor, after many experiments, we discover every parameter of composite electro - brush plating, includes voltage of brush plating, relative velocity of between brush plating pen and workpiece, adding quantity of diamond micro powder etc. finally steel balls millstone covering with ni - fe - diamond composite electro - brush plating film is produced successfully

    試驗中加入粒度為w0 . 5的金剛石微粉，通過反復多次的試驗，確定出了鎳-鐵-金剛石復合電刷鍍中的各項工藝參數，包括電壓、鍍筆和工件的相對速度、金剛石微粉的加入量、溫度等等工藝參數；成功的試製成了覆蓋有鎳-鐵-金剛石復合電刷鍍層的鋼球研磨板。
  8. Methods of testing vitreous enamel finishes - determination of resistance to thermal shock of coatings for fabricated sheet steel components such as burners and pan supports for cookers

    搪瓷釉層試驗方法.第22部分:炊用爐燃燒器具和炊具支架類薄鋼板組件覆層的耐溫度沖擊性測定
  9. ( 3 ) this thesis deduces the predigestion calculating method for calculating the section stress redistributed by the effects of concrete shrinkage, creep and difference temperature of pre - stressed lager cantilever composite beam with corrugated steel webs

    （ 3 ）推導了預應力波形鋼腹板組合挑梁關于徐變、收縮及溫度效應下的截面應力分佈簡化計算方法。
  10. The obtained results has been shown that the temperature field of sfrc pavement structure is non - linearly distributed along its thickness. the temperature which is close to the surface changes quickly, whereas slowly which is far. under the affect of temperature field, the temperture stress of sfrc pavement structure is also distributed non - linearly. the deflection and stress responses of sfrc pavement structure are waved declingly under the effect of shock load

    計算結果表明：鋼纖維混凝土路面板結構的溫度場沿其厚度方向呈非線性分佈；在距路面表面較近的地方，溫度變化較快，而在距路面表面較遠的地方，溫度沿厚度方向的變化較為緩慢，整個圖形呈下凸形。鋼纖維混凝土路面板在上述溫度載荷的作用下，其溫度應力沿其厚度方向呈非線性分佈。
  11. In the aspect of improving the cracking feature, compatibility and flexibility, the author has done experiments, including strength, modulus of elasticity experiments, and design some experiments similar to the practical structure and circumstance including adhesion strength between fresh mortars and old ones, between mortar and polystyrene board, mortar shrinkage in concrete circle, mortar shrinkage at different strength and different polymer - cement ratio, and temperature deformability at different strength and different polymer - cement ratio on mortars, on different type of formwork and on mortars with different type of formwork

    在改善砂漿抗裂性、提高柔韌性和協調變形能力方面，進行了不同聚合物摻量的強度試驗、彈性模量試驗；設計了與模網混凝土實際結構和情況相接近的新老砂漿粘結強度試驗、砂漿與苯板的粘結試驗以及混凝土環中的砂漿收縮試驗；進行了不同強度、不同聚合物摻量下的砂漿干縮變形試驗、溫度變形試驗，以及不同結構形式的鋼網自身溫度變形試驗和配有鋼網的砂漿溫度變形試驗。
  12. Standard specification for pressure vessel plates, carbon steel, high strength, for moderate and lower temperature service

    中溫和低溫壓力容器用高強度碳素鋼板的標準規范
  13. This dissertation generalizes the test on the full - scale reinforced concrete simply - supported slabs and three - span continuous slabs under fire at the normal loading condition. the conclusion can be drawn from the test about the deformation of the both kinds of slabs and the specimen section temperature distribution. meanwhile, the failure modes, mechanism and internal force redistribution of the continuous slabs are analyzed

    本文對足尺鋼筋混凝土簡支板、三跨連續板進行了恆載下的受火試驗研究，通過試驗，給出了鋼筋混凝土簡支板和連續板在高溫下的變形、構件截面溫度分佈規律；分析了連續板的內力重分佈和破壞機構的特點。
  14. The next this text is based on the appearance theories, according to the characteristics that the temperature dispersion of super thick mass concrete planceer of high - rise building primarily is an even difference in temperature and an even constringency, suppose the level shears are line with the displacement, adopting a big physical volume concrete of planceer in flexibility foundation for plank computing model, from theoretically deducing the difference in temperature of mass concrete contracting should basic formula of dint, and analysis the crack rule and the influence factor of mass concrete temperature contract, and bringing up the theory calculation method about temperature stress of mass concrete and the biggest whole method that sprinkle the length, at the same time according to basic formula of the temperature stress of mass concrete and the concrete construction experience, bringing five technique measures to prevent the temperature crack of mass concrete

    其次本文以唯象理論為基礎，根據高層建築超厚底板大體積混凝土承受的溫差主要是均勻溫差和均勻收縮的特點，闡述了大體積混凝土溫度應力理論計算的簡化方法和最大整澆長度的計算方法，同時根據大體積混凝土溫度收縮應力基本公式和大體積混凝土結構施工經驗，提出了防止大體積混凝土溫度裂縫的五項技術措施。最後本文以廈門郵電大廈3 . 5m超厚底板施工為實例，從大體積混凝土溫度應力計算、混凝土保溫材料厚度計算、混凝土配合比的確定，鋼筋工程、模板工程、混凝土的泵送和澆築以及大體積混凝土內部溫度的監測和後期養護等方面進行了理論應用。
  15. High strength steel plates for pressure vessel for intermediate and moderate temperature service

    中溫壓力容器用高強度鋼板
  16. The experiments produced respectively al clad plate by impact & cold press methods under normal temperature. this paper studied the rules of sawtooth distortion, inspected the fibre structure and bond strength of samples, found technics parameters of produce clad plate and analyzed their infections on bond strength

    分別利用沖擊法和靜壓法在常溫下制備了覆al復合鋼板，研究了這兩種復合鋼板的鋸齒變形規律，檢測界面顯微組織和結合強度，找到制備復合鋼板的工藝參數，並分析其對復合鋼板結合的影響。
  17. Thermal and structure character of straight reheating furnace were analyzed in csp technological process. coupling with heat conduction differential equations of the thin slab and the furnace lining, the mathemat ical model of heat transfer is established in the long one dimension furnace by using zone method for making the model of radiant heat transfer. the effect of the moving velocity and kinds of the slab on temperature distribution in the furnace is discussed based upon the solutions to the mathematical model

    通過分析csp工藝中直通式輥底加熱爐的熱工及結構特性，採用區域法建立爐內輻射換熱數學模型，與加熱爐內連鑄坯及爐襯的一維導熱方程相耦合，建立長一維直通式輥底加熱爐爐內傳熱數學模型.通過對數學模型的求解，研究分析了不同的薄板坯移動速度及鋼種對加熱爐爐內溫度分佈的影響
  18. Abstract : in this paper, finite element method is applied to calculate the temperature field of two kinds of composite slab

    文摘:應用有限元程序分析了鋼-混凝土組合板的溫度場。
  19. Research on roller - type heat treatment furnace steel board temperature monitoring system

    輥底式熱處理爐鋼板溫度監測系統研究
  20. So it has practical meaning to study the influence of different reinforced concrete face - slab construction schemes on the temperature field and thermal stress field of reinforced concrete face - slab

    溫度應力與施工過程有著密切的聯系，因此研究鋼筋混凝土面板不同施工方案對面板溫度場和溫度應力的影響具有實際意義。
分享友人
分享到 Line

分享到臉書