鋼的顯微組織 的英文怎麼說

中文拼音 [gāngdexiǎnwéizǔzhī]
鋼的顯微組織 英文
steel microstructure
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 的 : 4次方是 The fourth power of 2 is direction
  • 顯 : Ⅰ形容詞1 （明顯） apparent; obvious; noticeable; evident 2 （有名聲有權勢的） illustrious and inf...
  • 組 : Ⅰ名詞1 （由不多的人員組成的單位） group 2 （姓氏） a surname Ⅱ動詞（組織） organize; form Ⅲ量詞（...
  • 織 : 動詞（編織） knit; weave
  • 顯微 : microadiography
  • 組織 : 1 （組織系統） organization; organized system 2 （組成） organize; form 3 [紡織] weave 4 [醫學] [...
  1. Microstructure analysis of ultra low carbon bainite steel

    超低碳貝氏體鋼的顯微組織分析
  2. The composite roll of high speed steel has the synthetical life of over ten times more than traditional high cr cast iron roll. now the research and production of the high speed steel for roll are very drastic. in this thesis, the microstructure, heat treatment and performance of high speed steel fe - 2 % c - 4 % v - 4 % mo - 5 % cr - x % w ( wt ) are studied systematically by using metallograph, method of lattice, xrd, sem, eds and hardness

    本文利用金相法（包括黑白金相和彩色金相） 、 x射線衍射（ xrd ） 、掃描電子顯微鏡（ sem ） 、能譜（ eds ）及洛氏硬度分析儀等手段，對復合軋輥用高速鋼fe - 2 c - 4 v - 4 mo - 5 cr - x w （其它部分如未作特殊註明均為質量分數）合金系的顯微組織、熱處理工藝及性能進行了系統地分析。
  3. Influence of re on microstructure of 10simn, 42mnv, 60mn2 steels

    2鋼顯微組織的影響
  4. The microstructure evolution of ferrite and pearlite in ecap was investigated by means of optical m icroscopy ( om ) and transmission electron microscopy ( tem )

    並運用光學顯微鏡（ om ） 、透射電子顯微鏡（ tem ）及維氏顯微硬度儀研究了ecap變形后45鋼中先共析鐵素體及珠光體組織的演變特徵。
  5. This paper deals with the magnetic acoustic emission ( mae ) characteristic of several kind of common steels. the effects of chemial composition, microstructure and stress on mae are discussed. it has been confirmed that mae tedhniqre can be used as a new non - destructive testing method

    對幾種常用鋼材的磁聲發射（ mae ）特性進行了測試，研究了材料的化學成分、顯微組織及應力狀態對材料磁聲發射的影響，從而進一步證實，磁聲發射技術作為無損檢測材料的一種新方法是可行的。
  6. Abstract : this paper deals with the magnetic acoustic emission ( mae ) characteristic of several kind of common steels. the effects of chemial composition, microstructure and stress on mae are discussed. it has been confirmed that mae tedhniqre can be used as a new non - destructive testing method

    文摘:對幾種常用鋼材的磁聲發射（ mae ）特性進行了測試，研究了材料的化學成分、顯微組織及應力狀態對材料磁聲發射的影響，從而進一步證實，磁聲發射技術作為無損檢測材料的一種新方法是可行的。
  7. On this basis, microstructures and mechanical properties of equal channel angular pressed ultra - low carbon steel ( 0. 001 % c ) are studied by the means of optical microscope, transmission electron microscope and electronic tensile equipment

    在此基礎上，通過採用光學顯微鏡、電子顯微鏡、電子拉伸機等方法，研究了超低碳鋼（ 0 . 001 c ）的ecap及組織性能。
  8. The mechanical parameters at high temperatures - reduction in area ( ra % ) and tensile strength ( o b ) are measured by means of gleeble - 2000 thermal simulating machine. fracture surfaces are analyzed by scanning electron microscopy and optical microscopy. the segregation of sn is also examined by auger electron spectroscopy

    通過測定試驗鋼種的高溫力學參數（斷面收縮率ra和抗拉強度_ b ） ，觀察金相顯微組織，分析掃描斷口形貌，測試第二相析出物和俄歇能譜試驗等方法，研究了殘留元素sn及冷卻速率對高溫力學性能的影響。
  9. According to structural characteristics of multi - phased alloy steels and the properties of ultrasonic propagation, microstructures characterization with different heat treatment processes ( normalizing, quenching / annealing, quenching plus low tempering, quenching plus high tempering ) for three steels ( 40cr, 38crmoal, gcrlssimn ) was studied experimentally by using ultrasonic methods. ultrasonic velocity, relative attenuation coefficient, and power spectral analyses were researched on the same samples respectively, on the basis of theory and experiment, the sensitivity and other characterizations of the three methods used to distinguish different microstructures were compared

    根據具有多種相結構合金鋼不同熱處理轉變產物的組織特點，以及超聲波在其中的傳播規律，利用超聲波速度、相對衰減系數以及功率譜分析三種方法，對三種鋼（ 40cr 、 38crmoal及gcr15simn ）不同熱處理（正火、淬火退火、淬火+低溫回火及淬火+高溫回火）轉變產物的顯微組織進行了超聲表徵研究。
  10. In this paper, the microstructures of the joints of aluminum - bronze surfacing on mild steel and on stainless steel are analyzed by means of sem, and the division and formation of bronze / steel joint bond are studied

    藉助于電子顯微鏡技術對在低碳鋼和不銹鋼上堆焊鋁青銅的接頭的組織進行了分析，並對鋁青銅接頭熔合區的形成和區域劃分進行了探討
  11. Abstract : in this paper, the microstructures of the joints of aluminum - bronze surfacing on mild steel and on stainless steel are analyzed by means of sem, and the division and formation of bronze / steel joint bond are studied

    文摘:藉助于電子顯微鏡技術對在低碳鋼和不銹鋼上堆焊鋁青銅的接頭的組織進行了分析，並對鋁青銅接頭熔合區的形成和區域劃分進行了探討
  12. The experiments produced respectively al clad plate by impact & cold press methods under normal temperature. this paper studied the rules of sawtooth distortion, inspected the fibre structure and bond strength of samples, found technics parameters of produce clad plate and analyzed their infections on bond strength

    分別利用沖擊法和靜壓法在常溫下制備了覆al復合鋼板，研究了這兩種復合鋼板的鋸齒變形規律，檢測界面顯微組織和結合強度，找到制備復合鋼板的工藝參數，並分析其對復合鋼板結合的影響。
  13. Steel - determination of microstructure

    鋼的顯微組織評定方法
  14. Formation and strength - toughness behavior of acicular ferrite in an ultralow carbon steel for line pipe

    顯微組織對管線鋼硫化物應力腐蝕開裂的影響
  15. The twin roll casted austenite stainless steel strip was cold rolled, and the surface quality and the microstructure of the strip was investigated

    摘要對雙輥鑄軋704不銹鋼薄帶進行了冷軋處理，分析了冷軋前後薄帶的表面質量及顯微組織。
  16. On the base of the research of composition, the influence of modification with re, ti, mg, re - ti - mg ( wt, % ) on high speed steel of composite roll is investigated emphatically

    在對化學成分研究的基礎上，重點研究了利用re 、 ti 、 mg 、 re - ti - mg -進行變質處理對復合軋輥用高速鋼顯微組織的影響。
  17. After clad plate is rolled, the thickness of al plate has a few changes. the tests firstly produced al clad plate under cold press, then dealed with it under certain temperature. tests tried to find a sound temperature to weaken the

    先對鋁板和鋼板進行冷壓初復合，再在一定溫度下進行熱壓復合，試圖找到合適的熱壓溫度，消除界面脆化，提高復合鋼板的界面力學性能，檢測了試樣的顯微組織和結合強度。
分享友人
分享到 Line

分享到臉書