鋼筋箍 的英文怎麼說
中文拼音 [gāngjīngū]
鋼筋箍
英文
stirrup-
Aseismatic strengthening of reinforced concrete short column with steel plate hoops
鋼筋混凝土短柱利用外包鋼板箍抗震加固的設計Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete
通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。The content of the paper is nonlinear analysis of complete response process for t, l - shaped and " + " shaped section r. c. columns under axial compression and biaxial bending. on the basis of related papers, the full path of stress - strain relation of concrete and the sliding of longitudinal reinforcement anchoring are all considered, simultaneously, the restriction effect for concrete by thickening of stirrups is also included
本論文主要內容是對鋼筋混凝土異形截面雙向壓彎柱（包括l形、 t形、十字形柱）進行非線形全過程分析，在有關文獻基礎上考慮了受拉縱筋和周圍混凝土的錨固滑移和混凝土應力?應變關系曲線的下降段，同時考慮到在箍筋加密區箍筋對混凝土的約束影響。Secondly, this paper made some theoretic researches on its engineering classfication and applicable scope for this technology ; then combining with project example, this paper carried out scheme design for this technology, and compared some different kinds of underpinning scheme and node and structure design, and put forward the method of " reinforcce steel bar through column " to build pile cap beam, " resistant bend and shear anchored reinforce steel bar " to strengthen column consolidation effect, and the method of " steel plate hoop " to build reinforcing bar connection of the foundation beam, etc. in the process of the consturction scheme research and implement, this paper synthetically elaborated the organizaton for project construction, put forward the construction technical measure of specific aim on the artificial pile, and pile cap beam, and underground adding layer and structure stabilization, and overall structure stabilization and so on. for this project, adopt reinforcing bar concrete to brace hole wall to ensure the safety of engineering in the artificial pile construction, use flexible connection catch to make the cage hoisting easier to simplify the construction process, use the method of earthwork statified symmetrical balance in the process of underground adding layer excavation
本文首先對于基礎托換與結構加固技術的目的和意義、國內外發展狀況進行了綜合闡述；其次對該項技術工程分類及適應范圍進行了理論上的分析研究；然後結合工程實例對該項技術進行了方案設計，對比幾種不同的托換方案和節點及構造設計，提出了「通筋穿柱法」做承臺梁， 「抗彎抗剪錨筋法」強化柱加固效果， 「鋼板箍法」做地基梁鋼筋連接點等多項技術；在施工方案的研究和實施過程中，對于工程施工組織進行綜合闡述，並就人工挖孔樁、承臺梁、地下加層及結構加固、整體結構穩定等專項施工方案提出有針對性的施工技術措施，人工挖孔樁施工採用鋼筋砼護壁確保挖孔樁的安全成型，使用柔性連接鉤進行鋼筋籠吊裝簡化施工工序；承臺梁施工採用梁主筋橫穿柱身化學膠錨固等；地下加層綜合施工技術採用土方分層對稱平衡開挖，分段挖土做筏基結構自穩等；最後對于該工程實施后的效果分析，說明該項綜合施工技術的可行性。Fixed railway installations. equipment for overhead telecommunication and signalling lines. bracing collars for reinforced concrete posts
鐵路固定裝置.通訊和信號裝置架空線路用器材.鋼筋混凝土電桿支撐卡箍Based on the pseudo - static experimental results of nine abnormal joints, the damage process of abnormal joint is divided into four stages of original crack, entire crack, ultimate state and failure, the effect of axial force ratio, stirrup ratio and height of column section on seismic behavior of abnormal joint are discussed, the conclusion that anti - shear capacity of abnormal joint are studied in entire crack state by studying the minor core of abnormal joint is made, the calculating formula for anti - shear capacity of abnormal joint is proposed with a view to asymmetry in stirrup yield
摘要根據9個鋼筋混凝土框架異型節點試件的擬靜力試驗結果，指出異型節點受力過程分為初裂、通裂、極限和破壞4個階段；討論了軸壓比、節點核芯配箍率、柱截面高度變化對異型節點抗剪性能的影響；提出應考慮節點核芯區箍筋屈服的不均勻性並在通裂狀態下以「小核芯」為分析單元來研究此類節點抗剪承載力的建議；最終給出了異型節點抗剪承載力的計算公式。The influence of such parameters as axial load index, aspect ratio and percentages of lateral reinforcement, on seismic performance of reinforced concrete frame column in hong kong and analyses the distribution relationships of flexural deformation, shear deformation and slippage of longitudinal reinforcement in joint zone
根據試驗結果，討論了軸壓比、配箍率、剪跨比等參數對其抗震性能的影響，分析了水平荷載作用時塑性鉸區的彎曲變形、剪切變形和縱向鋼筋粘結滑移變形所產生的位移在框架柱總水平側移中所佔的比例及其變化規律。Stirrup joints ( congruence ) should be staggered in the last two of erect steel
箍筋的接頭（彎鉤疊合處）應交錯布置在兩根架立鋼筋上There is not composite enhancing effect to shear resistance of reinforced concrete beams between steel fiber and stirrups
鋼纖維與箍筋之間在提高鋼筋混凝土梁斜截面承載力方面不存在「藕合增強效應」 。According to the test of the shear beams reinforced with the stirrup of hrb400 steel bars, the mechanical property of stirrup in the members is studied
通過hrb400級鋼筋作箍筋的不同剪跨比的受剪梁的試驗，分析了此類鋼筋作箍筋的受力情況。In this paper, on the foundation of synthesizing engineering practice and study result of planted bar technique by chemistry glue on the domestic and international, embedded experiment study and theories analysis are done about bonded anchor behavior of chemistry planted bar anchorage behavior in this paper, the experimental results of 32 pulling resistance test ( meiya z3530 ) are given, considering some factors to affect bonded anchor behavior of chemistry planted bar such as the strength of concrete anchorage lengths diameter of steel bar and holes thickness of the protecting layer confecting circumstance of the hoop bar and quantity of construction especially which is very easy to be neglected and so on, and bonded anchor mechanism failure mode load carrying capacity and slide behavior are analyzed in - depth
本文在綜合國內外化學膠植筋技術的工程實踐和研究成果的基礎上，對化學植筋的粘結錨固性能作了較深入的試驗研究和理論分析。文中通過32個化學膠（美亞z3530 ）植筋試件的拉拔試驗研究，考慮混凝土強度、錨固長度、鋼筋植筋、鉆孔孔徑、保護層厚度、箍筋配製情況及施工質量等因素對植筋粘結性能的影響，特別是植筋的施工質量對粘結性能的影響是比較容易被忽視的因素，對化學植筋的粘結錨固機理、破壞形態、承載力及滑移性能作了比較深入的剖析。At first, development of various cracks carefully recorded and strains on both the rebars and the stirrups were measured in detail, together with the deflections of the beam. in such a way, correlation between the measured strain profiles of the reinforcement and the observed cracking development of each specimen was pursued. principal factors contributing to the cracking pattern and failure mode were figured out as a result
首先，通過單調靜力加載試驗研究，對梁的裂縫延伸和開展、縱筋應變、箍筋應變、梁的撓度等指標進行了細致的量測，試圖追蹤每一試件在裂縫發展及破壞過程中縱筋應變狀態的變化和裂縫發展程度的相關性，進而總結出有腹筋約束梁裂縫開展及鋼筋應力分佈的一般規律。Then the coupling beams with new reinforcement layout were made an inquiry into, and the improvement on the seismic behavior by coupling beams diagonally reinforced with a few rows in end regions was found out at last, based on the observations of the experimental phenomena and the analysis of the measurement result, and by the comparison of seismic behavior by making use of hysteretic response, ductility and energy dissipation behavior, a conclusion is presented : the code for design and construction of reinforced concrete high - rise structures ( the draft asked for advise hi 2000 ) ca n ' t ensure that the coupling beams have fairly good seismic ductility ; the result of improvement of the seismic ductility of the coupling beams by the increase hi stirrups besides the strengthen of longitudinal detailing reinforcement was n ' t obvious ; the coupling beams diagonally reinforced with a few rows in end regions have fairly good mechanisms, and the ductility and the behavior of energy dissipation are better than conventionally reinforced concrete coupling beams, so it is suitable to te tised in short coupling beams
本文通過對三根小跨高比（均為l h = 1 . 0 ）剪力墻洞口連系梁在低周反復荷載作用下的試驗，了解了嚴格按《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）設計的連梁具有的抗震性能，研究了採取增大連梁配箍量同時加強縱向構造筋的方案對抗震性能的影響，並進一步對新的配筋形式的連梁進行了探討，了解了在連梁梁端配置多排交叉斜筋方案對連梁抗震性能的改善。通過對試驗現象的觀察和量測結果的分析，利用荷載?位移滯回曲線、延性和耗能性能等指標對各個試件的抗震性能進行了比較，最後得出結論： 《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）不能保證小跨高比連梁具有較好的抗震延性：通過增大連梁配箍量同時加強縱向構造筋的方案對改善連梁的抗震延性的效果不太明顯；梁端配置多排交叉斜筋的連梁具有相對較好的受力性能，其延性和耗能性能等各項性能指標均優于普通配筋連梁，宜在深連梁中採用。Until now, the domestic and overseas scholar has studied the factors that have effect on performance of steel fiber reinforced concrete corbel such as shear span to depth, strength of concrete, reinforcement ratio ( including longitudinal reinforcement and stirrup ) and ratio of horizontal to vertical load. for calculating the cracking load, and ultimate load domestic and foreign scholar has brought forward a series of calculative formulas and methods have been put forward that based on statistical analysis, flexural model and truss model
到目前為止，國內外學者已研究了剪跨比、混凝土強度、配筋率（包括縱向鋼筋和箍筋） 、水平荷載與垂直荷載之比等因素對鋼筋鋼纖維混凝土牛腿受力性能的影響，對牛腿的抗裂計算和承載力的計算，國內外學者曾提出了基於數理統計分析、彎壓模型和桁架模型等的一系列計算方法和計算公式。In this paper, nonlinear behavior of reinforcement concrete combined torsion members subjected to axial compression, bending moment, shear and torsion is analyzed and researched with nonlinear finite element method. concrete has been modeled using eight - node hexahedral isoperimetric element and reinforcement element are divided into two cases. longitudinal reinforcement has been modeled with discrete element and stirrup has been modeled with smeared element
在建立鋼筋混凝土的有限元模型時，混凝土採用的單元為八節點六面體等參單元，鋼筋單元分為兩種情況，縱向鋼筋採用分離式鋼筋單元，箍筋採用埋藏式鋼筋單元，即箍筋作為附著在混凝土等參數單元內或單元上的「膜單元」 。Inclined stirrups are not effective in beams resisting shear reversals, such as seismic loads, because the reversals will cause cracking parallel to the inclined reinforcement, rendering it ineffective
也就是說，哪怕縱向鋼筋不彎起（保證支座叢筋在上下都足以抵抗地震力產生的彎矩） ，箍筋用斜的，也不行！A seismic shear capacity equation for ductility and non - ductility columns is proposed to amount for the reduced shear contribution of concrete as to the increasing of displacement ductility levels. 6. the behavior of columns * transverse displacement within yield hinge regions is also discussed based on truss - arch model. 7. the seismic shear capacity design equation of columns with various ductility levels is proposed in statistic method on the basis of test data collected from japan and china to simplify the equation resulted from truss - arch model
對國內外試驗資料進行了統計分析，詳細分析了剪跨比、軸壓比及配箍特徵值對框架柱構件抗剪承載力的影響，得到了反復荷載下框架柱塑性鉸區域極限承載力計算的統計公式；在理論推導公式及統計公式的基礎上，參考國內外規范，首次管品武；鋼筋混凝土框架柱塑性鉸區抗剪承載力試驗研究及機理分析提出了鋼筋混凝土框架柱塑性鉸區域剪切承載力抗震延性設計實用公式。The effect and safety of reinforced concrete column strengthened with bonded external angle steel are related with many factors, such as reinforced design, process of reinforcement, anchored structure of reinforced end, reinforcement rate of the angle steel, ductility and the stress applied on original column as well as maintenance in use
摘要採用外包角鋼加固的鋼筋混凝土柱、其加固效果和安全性與諸多因素，如加固設計、加固施工工藝、加固端錨固構造、加固角鋼的增鋼率與增箍率、原柱所處的應力狀態、使用過程中的維護管理等有關。Limited value of axial compression ratio and detailing requirements for stirrup of special shaped rc column
鋼筋混凝土異形柱的軸壓比限值與配箍構造First, the paper sets up finite element models of 4 - point bending rc beam strengthened with frp sheet. not only material nonlinear of concrete and steel bar but bond style of longitudinal steel, stirrup and frp are taken into account
本文首先建立了纖維布加固鋼筋混凝土梁四點彎曲的有限元模型，考慮了混凝土、鋼筋的材料非線性以及縱向鋼筋、箍筋和纖維布與混凝土之間的聯結關系。分享友人