鋼設計 的英文怎麼說
中文拼音 [gāngshèjì]
鋼設計
英文
steel design-
On the basis of the basic theory of metal distortion, using round steel alit rolling as entity model and combining with production practice, the selection of slit location, slit mode and the design parameter of slit pass system were analyzed, and the area calculation model of pre - slit rolled piece and slit rolled piece was built
摘要基於金屬塑性變形基本理論,以圓鋼雙線切分為基本實體模型,結合生產實踐,對切分位置、切分方式的選擇和切分孔型系統的設計參數進行了分析,並建立了預切分軋件和切分軋件的面積計算模型。Carried on the optimized design using the optimized design module to the support, finally changed to 14 equal - angle iron to replace the used steel
利用優化設計模塊對支架進行了優化設計,結果改用14號等邊角鋼代替原主弦桿用鋼。Aseismatic strengthening of reinforced concrete short column with steel plate hoops
鋼筋混凝土短柱利用外包鋼板箍抗震加固的設計Abstract : this paper explains the design of piercing die for steel tube, especially the manufacturing process using bench worker ' s experience to reduce the manufacturing cost. meanwhile, it also introduces the design of bending die for steel tube using the principle of take - out - slug, which can improve the work efficiency
文摘:介紹鋼管沖孔模具的設計,如何利用鉗工的操作技能來製造上、下沖孔模具,降低製造成本;以及不用抽芯塊的原理來設計鋼管彎曲模具,從而提高工作效率。1 mould design and manufacture : plastic injection steel mould, blow moulding mould
1模具設計製造:塑料射出成型鋼模,中空成型模具Design of half - through steel pipe bowstring concrete arch bridge of long - span, and knowledges to it
大跨度中承式鋼管系桿混凝土拱橋設計和體會In brief : in this passage you will get knowledge mainly about no. 5 step - by - step furnace equipped in the hot rolling mill of bx steel co. in the aspect of the advanced technique, equipment and know - how
摘要重點介紹了本鋼熱連軋廠5 (上標# )步進梁式加熱爐在設計當中採用先進的工藝、設備和技術,並提供了各種備件、材料在加熱爐上使用的實際效果。Manufactured and designed according to jb / t2603 - 94 standard, the product is a light and small crane hanged under the below of " 工 " type steel assisting with cd1 and md1 electronic calabash
本產品是按jb / t2603 - 94標準設計製造的,與cd1型和md1型電動葫蘆配套使用,懸掛在工字鋼下翼的輕小型起重機。Abstract : the paper shows the design concept, operation onsite, problemscaused and relative solutions to solve the problems for the automatic carburetting device in electric steelmaking in xi ning steel works
文摘:闡述了西寧鋼鐵廠電爐煉鋼自動增碳設備的設計思想,介紹了現場使用情況、出現的問題及具體解決辦法。Specification of frp equipment design for chemical industry
玻璃鋼化工設備設計規定The designer chooses the layout of reinforcement.
設計者選擇鋼筋布置。4th ladder coconut palm for channel steel type design anti - curving performance although surpasses the first generation, but still insufficient ideal
4梯梆為槽鋼式設計,抗彎曲性能雖然優于第一代,但依然不夠理想。Calculation of eccentric compression member with ring section in non - uniform reinforcement
鋼筋混凝土小偏心受壓構件對稱配筋截面設計There is no relavant content in corbels in steel fiber reinforced concrete regulations of structural design and construction ( cecs38 : 92 ). accordingly the design of steel fiber reinforced corbels does not have any regulations to follow
國內現行的《鋼纖維混凝土結構設計與施工規程》 ( cecs38 : 92 )也沒有相關的內容,使得鋼筋鋼纖維混凝土牛腿的設計無章可循。Thus the use of steel fiber reinforcement concrete in corbel can avoid complicated calculating in design, and the diminish difficulty of construction, at the same time when corbel ' s dimension can not be increased the reinforcement concrete corbel ' s ultimate load capacity and anti - seismic performance can be improved by the addition steel fiber into concrete. this method has become a kind of applied method and is highly concerned by the domestic and international academe and engineer group
因此,在配筋密集的牛腿中使用鋼纖維混凝土可以避免設計時繁雜的配筋計算、減小施工難度,同時在牛腿截面尺寸不能增大的情況下,可以通過加入鋼纖維來提高鋼筋混凝土牛腿的承載力和抗震性能,用鋼纖維加入鋼筋混凝土牛腿已成為一種實用方法受到了國內外學術界和工程界的極大關注。All part in touch with raw materials are made of stainless - steel
原料接觸面為全不銹鋼設計。Enter the raw material the staincess, venverievt deaning
進料斗不銹鋼設計,方便清洗。Foundation bars for indoor switchgear ; design and mounting particulars
戶內開關設備用槽鋼設計與安裝詳細說明Robustly designed in stainless steel, gas pressure thermometers are used for special measuring tasks in the range between - 200c and 700c
氣壓溫度計採用不銹鋼設計,堅固耐用,用於特殊的測量任務,溫度范圍在- 200c到700c 。Stainless steel trays can keep the material from pollution
托盤為不銹鋼設計,可排除在烘乾過程中造成污染的弊端。分享友人