錐度 的英文怎麼說

中文拼音 [zhuīdù]
錐度 英文
[機械工程] taper; conical degree錐度比 taper ratio; 錐度規 taper gauge
  • 錐 : Ⅰ名詞1. （錐子） awl2. （似錐物） awl-shaped things 3. （錐體） cone Ⅱ動詞（鉆） drill; bore
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. Clamping devices ; milling machine arbors with taper

    夾緊裝置.帶錐度銑床心軸
  2. The study is imitating subulate tool penterite armor fabric by method of test for puncture of paperboard and corrugated fiberboard, and to ascertain the laver of armor fabric for absorb energy and arrestment, and any difference angle to compare the rank of defying ball, for understanding the sharp to the rank of annor fabric defy penterite energy, and penterite deep, the lose energy relation of sharp

    摘要本研究是以沖孔強度試驗機測試，模擬尖錐利器攻擊穿刺防彈衣，且對于防彈衣層數間的阻抗作用及能量吸收的情形，並對各種不同角度的抗彈織物疊層排列作相互比較，進而?解尖錐對防彈衣的抗穿透層數之能量及穿透深度、錐度之能量耗損之間關系。
  3. Study on conical basket centrifuge of double - cone angles

    雙錐度錐籃離心機的研究
  4. Cylindrical and 1 10 conical shaft ends. general

    圓柱的和1 10錐度的錐形軸端.總則
  5. Conicity effect of tyres and ways of correction

    輪胎錐度效應及其糾偏途徑
  6. Stressed - type fastenings with taper action ; taper keys with gip head, keyways, dimensions and application

    錐度驅動應力型緊固件.彎頭斜鍵鍵槽尺寸和應用
  7. Small craft with inboard engine - propeller shaft ends and bosses with 1 : 16taper

    舷內機小艇錐度為1 : 16的螺旋槳軸端和槳轂
  8. Small craft with inboard engine - propeller shaft ends and bosses with 1 : 10 taper

    舷內機小艇錐度為1 : 10的螺旋槳軸端和槳轂
  9. Machine tools - self - holding tapers for tool shanks

    機床工具.刀柄用自動夾緊錐度
  10. Electrode taper fits for spot welding equipment - dimensions

    點焊設備電極錐度配合尺寸
  11. Resistance spot welding. electrode holders. part 1 : tapper fixing 1 : 10

    電阻點焊.電極夾頭.第1部分:固定錐度為1 : 10
  12. Accoding to experiment, found that trepanning can obtain the holes of little taper, high roundness, using laser drilling of nearby the last energy threshold gained the holes of high quality

    最終得出:在工件上打大孔徑的孔時，採用旋切打孔的方法可以得到了圓度高、錐度小的孔質量。
  13. Morse taper gauges ; taper plug gauges for taper sockets with drift slot

    莫氏錐度量規.第1部分:帶退柄孔錐套用錐度塞規
  14. Metric taper gauges ; taper plug gauges for taper sockets with drift slot

    公制錐度量規.第1部分:帶退柄孔錐套用錐度量規
  15. Drill chuck tapers iso 239 : 1999

    鉆夾頭錐度
  16. Drill chuck tapers

    鉆夾頭錐度
  17. Drilling hammers ; taper gauges for tapered connections of drill rods and bits

    打眼錘.鉆桿和鉆頭圓錐連接用錐度量規
  18. The influence of waviness and taper of seal faces to the operating performance at slow speed of gas face seal

    低速運轉氣膜機械密封端面波度和錐度對其密封性能的影響
  19. Test method for measuring edge taper and crown of flat - rolled electrical steel coils

    平滾軋電工鋼卷材邊緣錐度和凸面的測量方法
  20. Standard test method for measuring edge taper and crown of flat - rolled electrical steel coils

    扁軋電工鋼卷板邊緣錐度和凸面測量的標準試驗方法
分享友人
分享到 Line

分享到臉書