鍵和鍵槽 的英文怎麼說

中文拼音 [jiànhéjiàncáo]
鍵和鍵槽 英文
keys and keyways splines
  • 鍵 : 名詞1 [機械工程] （使軸與齒輪、皮帶輪等連接並固定在一起的零件） key 2 [書面語] （插門的金屬棍子）...
  • 和 : 和動詞（在粉狀物中加液體攪拌或揉弄使有黏性） mix （powder） with water, etc. : 和點兒灰泥 prepare some plaster
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  1. Bores and keyways for flexible couplings metric series

    柔性耦合器的鏜孔和鍵槽
  2. Bores and keyways for flexible couplings inch series

    柔性耦合器的鏜孔和鍵槽
  3. Rod - ends with self - aligning ball bearings. long threaded shank and keyway. dimensions and loads

    帶自位球軸承的桿端.長螺紋桿和鍵槽.尺寸和負荷
  4. Semi - circular woodruff keys - dimensions of cross sections and keyways

    鍵和鍵槽的剖面尺寸
  5. Mechanical transmissions. tangential keys and keyways. dimensions and tolerances

    機械傳動.切向鍵和鍵槽.尺寸和公差
  6. Square and rectangular keys and keyways - width tolerances and deviations greater than basic size

    方形和矩形鍵和鍵槽.寬度公差和大於基本尺寸的偏差
  7. Shipbuilding. shaft lines. keys and keyways for tapers on propeller - shafts. diameters 100 mm to 680 mm. alternative

    造船工業.軸線.直徑為mm mm的螺旋槳軸上錐形體的鍵和鍵槽.可選擇的
  8. Taper keys - cross section dimensions of keys and keyways

    鍵和鍵槽的剖面尺寸
  9. Parallel keys - dimensions of cross sections and keyways

    鍵和鍵槽的剖面尺寸
  10. Square and rectangular keys and keyways

    四方型和矩型鍵和鍵槽
  11. Thin flat keys - cross section dimensions and keyways

    鍵和鍵槽的剖面尺寸
  12. Keys and keyways and taper pins - specification - keys and keyways

    鍵和鍵槽及錐形銷.鍵和鍵槽規范
  13. Woodruff keys and keyseats

    月牙鍵和鍵槽
  14. Woodruff keys and keyways

    月牙鍵和鍵槽
  15. Square and rect keys and keyways : width tolerances and deviations greater than basic size

    方頭和長方頭鍵和鍵槽:大於基本尺寸的寬度公差和偏差
  16. Woodruff keys keyways

    半圓鍵和鍵槽
  17. Keys and keyways and taper pins - specification for solid and split taper pins for general engineering purposes

    鍵和鍵槽及錐形銷.第3部分:一般工程用整體的和開口錐形銷規范
  18. Specification for metric keys and keyways - parallel and taper keys

    米制鍵及鍵槽規范.第1部分:平鍵和錐形鍵
  19. 1 10 conical shaft ends with or without parallel keys and keyways. short series. dimensions

    帶或不帶平行鍵和鍵槽的錐形軸端.短系列.尺寸
  20. 1 10 conical shaft ends with or without parallel keys and keyways normal longs series. dimensions

    帶或不帶平行鍵和鍵槽的錐形軸端.通用長系列.尺寸
分享友人
分享到 Line

分享到臉書