鑄造氣孔 的英文怎麼說
中文拼音 [zhùzàoqìkǒng]
鑄造氣孔
英文
cast pocker- 鑄 : Ⅰ動詞(鑄造) cast; coin; make Ⅱ名詞1. (古國名) zhu, a state in the zhou dynasty2. (姓氏) a surname
- 造 : Ⅰ動詞1 (做; 製作) make; build; create; produce 2 (假編) cook up; fabricate; concoct 3 [書面語...
- 氣 : Ⅰ名詞1 (氣體) gas 2 (空氣) air 3 (氣息) breath 4 (自然界冷熱陰晴等現象) weather 5 (氣味...
- 鑄造 : [冶金學] cast-on outwell; foundry; cast; casting; found; founding
- 氣孔 : [礦物學] blowhole; [植物學] stoma; [動物學] spiracle; pore; stigma; [冶金學] gas hole; gas pocket; [建築] air hole
-
Characteristics such as exudation, voids, brittleness and irreversible expansion were noted in the preparation of a castable high explosive such as tnt.
諸如滲油、氣孔、發脆和不可回復膨脹等特性,在可鑄高錳炸藥如銻思銻的製造中,是很明顯的。The quality of furan sand castings is usually better than clay sand castings, however, some defects are also very easy take place with furan sand castings such as blow hole, metal penetration, veining, cracking, slag inclusion, hardness too low, surface recarburation, surface sulphuration, nodularity degeneration etc, which were usually caused by improper raw materials selection, improper method design, incorrect moulding or / and core - making
摘要呋喃樹脂砂鑄件質量一般比黏土砂鑄件好,但如果原材料選擇、工藝設計、造型和制芯操作不當,也會產生氣孔、粘砂、脈紋、裂紋,夾渣、硬度不足、滲碳、滲硫和球化不良等鑄造缺陷。Abstract : porosity of die castings caused by air entrapped into the liquid metal in the shot sleeve is common problem of die csating process
文摘:壓室中氣體捲入金屬液內而造成壓鑄件內部氣孔是壓鑄過程常見的問題。Test method for properties of investment casting ceramic core - part 1 : determination of apparent porosity, water absorption and bulk - density
熔模鑄造陶瓷型芯性能試驗方法第1部分:顯氣孔率吸水率和體積密度的測定Metal poured into a mold cavity during the casting process solidifies with the possibility of shrinkage, segregation or porosity, which can prevent an " as - poured " casting from being acceptable for severe applications
在鑄造過程中,澆鑄到模腔內的金屬在凝固過程中可能會產生收縮、分離或氣孔,這些問題使得「澆鑄」鑄件無法被苛刻環境應用領域所接受。The main properties of new alcohol based spraying coatings for green sand mold are superior to the abilities of internal and outside coatings of the same kind, the surfaces of castings that are produced used new alcohol based spraying coatings are smooth without adhering sand and gas - hore
粘土濕型砂鑄造新型醇基噴塗塗料的主要性能達到了國內外同類產品領先水平;生產的高錳鋼、可鍛鑄鐵和灰口鑄鐵產品表面光潔,無粘砂、氣孔等缺陷。In addition, imperfections like drag and gas holes were easy to turn out in the surface of epc casting for imperfect technology design, and this was verified by the actual castings
同時發現,在消失模鑄件表面容易因殘余泡沫而造成表面渣氣孔,實際鑄件的表面質量也證明了這一點。Based on the analysis for the reason causing choke, shrinkage and blow hole defects at two 216 bosses of the main plate of the offset machine, the method to eliminate the casting defects by carrying out qc activities was described
對01膠印機左右大墻板的兩個216圓臺易出現嗆火、縮孔和氣孔缺陷的原因進行了分析,介紹了開展qc活動消除01膠印機左右大墻板鑄造缺陷的方法。Important advantages are still achieved in cycle time reduction and the ability to cast near net shape castings with minimal porosity
最大的優點仍是減少生產周期,並且能鑄造出含有最少量氣孔的鑄件。分享友人