鑄造碳化鎢 的英文怎麼說

中文拼音 [zhùzàotànhuàwū]
鑄造碳化鎢 英文
cast tungsten carbide
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 造 : Ⅰ動詞1 （做; 製作） make; build; create; produce 2 （假編） cook up; fabricate; concoct 3 [書面語...
  • 碳 : 名詞[化學] （非金屬元素） carbon （c）
  • 鎢 : 名詞[化學] （金屬元素） tungsten; wolfram（w）
  • 鑄造 : [冶金學] cast-on outwell; foundry; cast; casting; found; founding
  1. The strength and wear resistance of diamond drill bits for petroleum exploitation will be increased considerably when cast tungsten carbide is applied and adheres to the substrate firmly with cast tungsten carbide of 80 - 200mesh as the skelton and copper alloy as the soldering material in a process of non - pressure immersion

    石油鉆探行業用的金剛石鉆頭，用粒度為80 ? 200目的鑄造碳化鎢粉作骨架，採用無壓浸漬工藝，以銅合金作釬焊料，將鑄造碳化鎢與基體牢固結合，強度、耐磨性大大提高。
  2. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  3. Their lifetime can be prolonged if they are repaired with cast tungsten carbide powder

    採用鑄造碳化鎢修補后，可以延長使用壽命。
  4. The results show that the composites were more wear resistant than the matrix, contributing to the " volume effect " and " size effect ", the wear resistance increases with the particle content and size. the composite shows better wear resistance than high chromium cast iron material especially in low load and fine abrasive test condition. the results also indicate that the composite strengthened by ageing treatment was more wear resistant than as - cast composite

    磨損試驗結果表明，鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料具有比較高的抗磨料磨損能力，而且其耐磨性隨著鑄造碳化鎢顆粒體積分數及尺寸的增大而提高，表現出了強烈的「體積效應」及「尺寸效應」 ，尤其是在低載荷、細磨料磨損條件下，復合材料表現出更好的而寸磨性，即使與高鉻鑄鐵（ cr28 ）相比也有很大程度的提高。
  5. This thesis fabricated successfully a wc particle reinforced iron matrix composite using a vacuum infiltration process for severely erosion and application in the slurry pump. the casting process was optimized. the microstructure and wear resistance were researched and analyzed

    本文針對承受嚴重沖蝕磨損的渣漿泵過流件，採用負壓鑄滲工藝成功制備了碳化鎢顆粒增強鐵基表面復合材料，改善和優化了復合工藝、鑄造工藝。
  6. The result showed that, by adopting appropriate casting method, a good metallurgical combination between tungsten particles and hi - cr alloyed cast iron could be obtained

    結果表明，在適宜的鑄造工藝條件下，碳化鎢顆粒和高鉻鑄鐵基體之間可以形成良好的冶金結合，鑄滲效果較好。
  7. It is preferable to use tungsten carbide of fine grain size for such build - up welding

    堆焊採用的鑄造碳化鎢顆粒，以細的為佳。
  8. Cast tungsten carbide

    鑄造碳化鎢
分享友人
分享到 Line

分享到臉書