長翅型 的英文怎麼說
中文拼音 [zhǎngchìxíng]
長翅型
英文
macropterous form-
Second, the starting and stopping behaviors under disturbed condition are analyzed and calculated by using the dynamic concentrative parameter model, which gives some advice to better prescribe refrigeration system and set theoretic foundation for carrying out automatic control of refrigeration system. third, the normal running process is analyzed and calculated by means of rational matching theory, which gives some advice on how to better understand the parameter change under steady state and the affection of inlet - parameter on evaporator. fourth, the simulation software with dynamic characteristic is designed, which can be applied to calculate thernio - parameter of cryogen, air humidity and frost thickness under different initial and boundary conditions, and to carry out dynamic simulation under conditions of dryness, wetness and frostiness, at the same time, to achieve detection and simulation at any stage from starting to stopping
本文的主要內容如下： 1 ）對翅片管蒸發器結構特點進行分析，選取適當的微元控制體，就干、濕和霜工況下對每個微元分別進行傳熱傳質分析，基於經驗關系式確定霜的有關參數，對于霜工況下的霜生長建立模型，經適當假設，運用質量守恆、能量守恆和動量守恆方程建立適合動態模擬的蒸發器數學模型，為系統模擬奠定基礎； 2 ）對蒸發在大擾動下的開、停機過程，運用動態集中參數模型進行分析和計算，為更好地描述製冷系統運行的全過程奠定基礎，同時也為製冷系統實現自動控制提供一定的理論基礎； 3 ）對蒸發器正常運行過程，運用動態分佈參數和參數間定量耦合的觀點來分析和計算，為更好地了解穩態工況下各點參數的變化情況及各入口參數對蒸發器動態特性的影響即蒸發器性能對各參數變化的敏感性； 4 ）編寫翅片管蒸發器動態特性模擬計算程序，可以計算不同邊界條件和初始條件下的製冷劑熱力參數、空氣溫濕度和霜厚度分佈場，實現對翅片管蒸發器在干、濕和霜工況下的動態模擬。The are medium - sized butterflies having narrow and elongated forewings and the forelegs are much reduced
珍蝶科為中型蝴蝶，擁有窄長的翅膀，前足退化。The plate - tube evaporator, the single back - fin evaporator and the box condenser. after analyzing the physical model and setting up the mathematical model according to the two - phase flow of adiabatic capillary tubes, it also numerically simulates and analyzes the different effects of main parameters on the capillary tube length. based on the heat transfer analysis and counting of thermal insulation layer, the cad system accomplishes the parametric design and drawings of the refrigerator body
該系統完成了對典型製冷裝置的換熱器部件，如板管式蒸發器、單脊翅片管式蒸發器、箱壁式冷凝器的參數化設計和繪圖；分析了絕熱型毛細管兩相流的物理模型，並建立數學模型，對絕熱型毛細管各主要參數對其長度的影響進行了數值模擬和計算分析；基於對電冰箱箱體絕熱層厚度的傳熱分析和計算，完成了整個箱體的參數化設計和繪圖工作。These methods are following : ( 1 ) in order to build fem model conveniently and enhance calculating speed, interceped a finite length and built a 2d - symmetry model. ( 2 ) in order to apply loads conveniently, kept the entrance of cold fluid. ( 3 ) in order to obtain numerical results in steady situation, lengthened export and import ends
這些方法主要有： （ 1 ）為了便於建立模型並提高計算速度，對于實際工程中採用的長徑比特別大的換熱管採取截取有限長度的方法並建立二維對稱簡化模型； （ 2 ）提出採取保留冷流體入口端，截取有限長度的方法施加載荷； （ 3 ）適當延長翅片管的出口端和入口端，以便獲得穩定工況的數值解。分享友人