閉合位形裝置 的英文怎麼說

中文拼音 [bìgěwèixíngzhuāngzhì]
閉合位形裝置 英文
closed geometry device
  • 閉 : Ⅰ動詞1. （關; 合） close; shut 2. （堵塞不通） block up; obstruct; stop up Ⅱ名詞（姓氏） a surname
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 閉合 : close; shutting; synizesis; synezesis; occlusio; closure; make; occlus-; occluso-
  • 裝置 : 1 （機器設備的配件）installation; device; apparatus; equipment; arrangement; gear; appliance; rig...
  1. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  2. Harmonized blank detail specification for lead screw actuated non - wirewound preset potentiometers - square form, container sealed, actuating device insulated from resistive element, slipping clutch at each end of travel, rigid terminations - assessment level s

    導螺桿傳動非線繞預調電位器協調空白詳細規范.正方形的容器密閉的與電阻元件絕緣的驅動裝置每個行程終止的滑動離合器剛性終端.評定級別s
分享友人
分享到 Line

分享到臉書