閉合短線 的英文怎麼說

中文拼音 [bìgěduǎnxiàn]
閉合短線 英文
closed stub
  • 閉 : Ⅰ動詞1. （關; 合） close; shut 2. （堵塞不通） block up; obstruct; stop up Ⅱ名詞（姓氏） a surname
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 短 : Ⅰ形容詞（空間、時間兩端之間的距離小） short; brief Ⅱ動詞（缺少; 欠） lack; owe Ⅲ名詞1 （缺點） we...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 閉合 : close; shutting; synizesis; synezesis; occlusio; closure; make; occlus-; occluso-
  • 短線 : hatchures
  1. Adopting the assummation that the quark interaction is the sum of the usual one - gluon direct exchange and the mixture of linear scalar and vector potentials, we structure the relativistic corrections of order v2 / c2to the cornell potential, including the annihilation potential for the quark and antiquark of the same favors which plays the same role with the one - gluon direct exchange at short distances. the effects of the relativistic corrections on the hyperfine splittings of quarkonium states are discussed, and a good fit to the available experimental data is obtained on heavy quarkonium mass spectra

    采納庫侖勢源於單膠子直接交換，而線性禁閉源於標量和矢量的混合，同時考慮在短程區域與單膠子直接交換起同樣作用的同味正反夸克的湮滅，構造了靜態夸克-反夸克勢到v ~ 2 c ~ 2級次的完全相對論修正，並擬合計算了重介子偶素的能譜，討論了相對論修正對重介子偶素能級分裂的作用。
  2. Then i sample the face, and use the bucket ( assuming all the lines are closed - which they weren ' t ) to fill the rest of the body, and a slight blue with a bit of the flesh color for the pants

    我在臉部取樣，使用油漆桶（假設所有的線條都閉合了? ?其實不會）來填充剩餘的身體部分，短褲使用帶一些肉色的淡藍色。
  3. The off - line program system based on cad / cam for dispensing robot is designed on the computer. in the module of trajectory planning, preliminary discussion is done about the shortest loop path and an algorithm of solving this problem is provided ; in the module of back procedure, dda ( digital differential analyzer ) is adopted in line, circle and ellipse interpolation. at last the protocol transferring program data to robot from off - line system is analyzed

    在離線編程的系統的設計中，實現了cad的建模、點膠軌跡的程序示教、工藝參數編輯、軌跡規劃、後置處理等功能，並在規劃模塊中針對平面內不規則排列點進行點膠的軌跡規劃進行了初步探討，採用圖論的方法，給出滿足實際要求且演算法復雜度較小的最短閉合迴路的程序演算法;在離線編程系統的後置處理模塊中，介紹了直線、圓弧、橢圓弧的dda插補方法以及脈沖分配不均勻的改進方法;最後對通信協議的制定進行了分析。
  4. The paper analyzed the struture of the tri - eccentric butterfly vavle at length, defined the tri - eccentric butterfly valve, educed the geometry function and its characteristic about the section of the butterfly disc. the results indicate : the parallel contour line across butterfly disc thickness is normal ellipse, thereby eslablished function relations between its geometry parameters ( long axis and short axis ) of three primary sections of the butterfly disc and the tri - eccentricity ; in order to avoid interference between the butterfly disc and the valve seat as well as the valve body, combining the torque, we obtained the feasible range about the rotation center of the tri - eccentric butterfly vavle

    本文主要分析了三偏心蝶閥的結構，給出了三偏心的定義，推導出了蝶板截面的幾何方程及其性質，結果表明，沿蝶板厚度的平行截面輪廓線為標準的橢圓形，進而推導出了蝶板幾個主要截面的幾何參數（長軸、短軸）與三個偏心之間的函數關系；考慮到蝶板啟閉過程中避免與閥體及閥座發生干涉，結合蝶板的啟閉扭矩，確立了三偏心蝶閥回轉中心的適宜區域。
  5. According to the structure characteristics and motion rules of the new type nursing robot, the close loop control system of this new type nursing robot is designed and made with the virtual instrument developing software labwindows / cvi, mcu, piezoelectric ultrasonic motor and high precision optical incremental encoder, which can make the robot reset and rotate by the predefined tracks. at the same time, in order to make the nursing robots used more widely where intensity, precision and price are not high, another control system is designed with the step motor, virtual instrument developing software labwindows / cvi, multi - function daq card pci1711, linear power amplifier. in order to use the nursing robots in acupuncture therapy, a simple finger is designed

    在對其結構特點和運動規律分析的基礎上，本文以虛擬儀器編程語言labwindows / cvi為軟體開發工具，以單片機為控制核心，以超聲電機為驅動元件，以高精度光電編碼器作為速度和角位移檢測裝置，實現了機械臂的復位以及預定軌跡的閉環控制系統的開發;同時為適應一些強度不大、精度要求不高的應用場合，也為降低成本，簡化控制裝置，推動新型護理機械臂短期內應用推廣的需要，以目前應用較為廣泛、控制技術較為成熟的步進電機為驅動元件，用labwindows / cvi開發環境、 pci1711數據採集卡以及線性功率放大器開發了一套控制系統，實現了手臂的復位、勻速運動以及預定軌跡的控制系統;為推廣護理機器人在針灸理療中應用，設計了簡單的手指機構並利用labwindows / cvi開發環境，以及智能材料驅動器? ?層疊式壓電驅動器，進行了手指的抓取以及對驅動對象的轉動控制。
分享友人
分享到 Line

分享到臉書