閥帽 的英文怎麼說
中文拼音 [fámào]-
Bonnet ? large extended type bonnet grade
閥帽-大型加長閥帽。Wcc valve bonnet and internals will be manufactured with 300 series ss and / or 21 / 4 cr
Wcc閥門的閥帽何閥內件採用300系列不銹鋼和/或21 / 4鉻製造。Wcc valve bonnets and internals will be manufactured with 300 series ss and / or 21 / 4 cr
Wcc閥門的閥帽何閥內件採用300系列不銹鋼和/或21 / 4鉻製造。Wcc valve bonnet and internals will be manufactured with 300 series stainless or 21 / 4 cr material
Wcc閥門的閥帽何閥內件採用300系列不銹鋼和/或21 / 4鉻製造。Unscrew and remove bonnet assembly
旋下螺絲,拆卸閥帽組件。Easy dismantling is made possible by dropping the bonnet assembly into the body cavity and driving out the four - segmental thrust rings by means of a push pin
將閥帽總裝拆離閥腔,採用推針取出四個部分的推力環,拆卸變得簡便易行。A complete list of replacement components can be found on the preceding page. bonnet assemblies and seals are interchangeable between angle and y - pattern valve bodies
更換部件的完整清單可以在前一頁找到。閥帽組件和密封在角形和y形閥體之間可以互換。Bonnet body seal
閥帽體密封Live - loading of bonnet bolting stores the required sealing load during a pressure or temperature induced transient
在壓力或溫度不斷波動轉換的情況下,動負載閥帽螺栓儲存了所需要的密封負載。For maximum versatility, both a and b type valves shall have inter - changeable bonnet / stem assemblies
為了使這些閥門具有最大的多功能性,類型a和b閥門都應該配置內部可更換的閥帽/閥桿總成。A lawyer returns to his parked bmw to find the headlights broken and considerable damage to the bonnet
一名律師來到停車場,發現他的寶馬車的前燈壞了,並且連閥帽也受到了很大程度的破損。Gate valves flat sided of gun metall with screwed bonnet and flanges, dn 20 to dn 100, pn 16
帶螺紋的閥帽和法蘭dn 20至dn 100 pn 16的炮銅制Unscrew the four bolts to separate the body from the bonnet and control group
擰松四個螺栓,從閥帽和控制組建之間分開閥體。Bypass unit cast into the bonnet prevents clogging
在閥帽內鑄入旁路,有利於避免堵塞。Air cylinder valve bonnet
氣筒閥帽罩Bolted bonnet gate valves for alkylation service ( hf acid service see page 19 )
適用於烴化物應用領域的螺栓閥帽閘閥(氟化氫酸應用領域請參閱第19頁) 。Valves shall be one of the types specified in 4. 2 to 4. 4, having flanged, threaded, capillary or compression ends, integral or renewable body seats and screwed, union or bolted bonnets or covers
閥門的類型應是4 . 2到4 . 4中所給出的類型,帶有法蘭/絲口/焊接或壓縮端面,帶有完整的或可更換的閥體,及螺紋式,聯接式或拴結式閥帽或閥蓋。All pressure containing parts within one body - bonnet forging ? no joints to leak or welds to cut for servicing
所有壓力部件都放置在閥體-閥帽鍛件內-沒有可能導致泄露的連接部位;在維護時,不需要切割任何焊接部位。The body - bonnet welds are made on fully automatic mig welders
閥體-閥帽的焊接工藝是採用完全自動化的mig焊接設備進行的。Pressure seal design without live load bonnet ( no spring washers ) : the gasket bolt tightness must be rechecked after operating test pressure and temperature has been achieved
沒有動負載閥帽的壓力密封結構(沒有彈簧墊圈) :在工作試驗壓力和溫度達到限制值時,必須重新檢查墊圈螺栓的緊固性。分享友人