閥底座 的英文怎麼說
中文拼音 [fádezuò]
閥底座
英文
valve base-
When flux appears liquid and transparent on both tube and valve, start sweeping flame back and forth along axis of joint to maintain heat on parts to be joined, especially toward base of valve socket
當焊劑變成液態並且在管道和閥門上呈現半透明狀態時,開始將火焰沿著連接部件的軸線進行進退烘烤,以保持連接部件、特別是閥門套筒底座部位的熱度。Take one body half and, starting at the bottom of the valve, work the end flap of the elastomeric seat into the opening of the body
拿起一半閥體,從閥門底部開始,將彈性材料閥座的邊緣放入閥體的開口處。After removal of body halves, the elastomeric seat can be removed from the disk / shaft manually by stretching the bottom of the seat over the lower end of the stem
閥體兩瓣拆卸開后,可以通過拉伸閥桿下部的閥座底層,手工將彈性材料閥座從閥瓣/閥軸上拆卸下來。Gate guides and lugs. 180 guiding for the moving gate, while jambs at the bottom hold the knife gate to assure proper seating
閘板導桿和凸耳。當底部側板為了保證提供恰當閥座時而夾住刀閘時, 180導桿用於閘板的移動。Reinstall the elbow into the base of the relief valve to hold the air gap drain in place
將彎頭安裝在安全閥的底座,將氣隙排放裝置固定住。Gravity ball check valves are converted to foot valves by replacing the union nut and end connector on the receiving end ? seat end ? of the body with an f. v. screen housing assembly
重力球形止回閥可以變為底閥,只需在接受埠-閥體的閥座埠,用一個f . v .濾網殼組件更換管接頭螺母和埠連接件即可。Blast furnace accessories. hot air valves. discs and seats, pn 6
高爐附件.熱風閥.閥蓋和底座pn6The seat material shall be one of the following materials : ethylene - propylene - diene monomer ( epdm ) or fluoroelastomer ( fpm ) with polytetrafluoroethylene ( ptfe ) bearing support at the top and bottom
閥座材料應該是下列材料之一:乙烯-丙烯-二烯系單體(三元乙丙橡膠)或氟橡膠( fpm ) ,在頂部和底部配置聚四氟乙烯( ptfe )軸承支撐。Pneumatic fluid power. directional control valve with four ports. mounting surfaces of subplate. pipe thread
氣壓流體動力.帶4個口的定向控制閥門.底座安裝表面.管材螺紋Pneumatic fluid power. directional control valve with three ports. mounting surfaces of subplate. pipe thread
氣壓流體動力.帶3個口的定向控制閥門.底座安裝表面.管材螺紋Handwheel torque or actuator force provides positive seat - knife closure. during closure, the stem slides down pushing the knife into contact with the two bottom lugs
手輪扭矩或執行機構扭力是正閥座-閘刀關閉的動力源。在關閉期間,閥桿向下滑動推動閘刀向下抵住兩個底部凸耳。To clean ; remove bottom plug, seat spring, strainer and seat disc
因此要清洗,拆卸底部塞、閥座彈簧、過濾器和閥座閥瓣。Remove the elbows from the relief valve base
從安全閥底座拆卸彎頭。分享友人