防漏閥 的英文怎麼說

中文拼音 [fánglóufá]
防漏閥 英文
anti-leak valve
  • 防 : Ⅰ動詞（防鷥） provide against; defend against; guard against Ⅱ名詞1 （防守; 防禦） defence 2 （堤...
  • 漏 : Ⅰ動詞1 （從孔或縫中滴下、透出或掉出） leak; drip 2 （泄漏） divulge; disclose; leak 3 （遺漏） le...
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 防漏 : sealing up防漏劑 leak preventive; 防漏鉚接 tight riveting; 防漏密封 leakproof seal
  1. Technical features, main requirements and process flow of sleeve valve barrel grouting method are described with the field cases of the method in grouting injection reinforcement, permeability proof and leakage treatment in china

    介紹了袖閥管注漿工法的特點、主要技術要求和施工工藝流程，以及該方法在國內注漿加固、防滲、堵漏施工中的應用實例。
  2. Abstract : technical features, main requirements and process flow of sleeve valve barrel grouting method are described with the field cases of the method in grouting injection reinforcement, permeability proof and leakage treatment in china

    文摘:介紹了袖閥管注漿工法的特點、主要技術要求和施工工藝流程，以及該方法在國內注漿加固、防滲、堵漏施工中的應用實例。
  3. In the joint of lg pex - a pipe, male xocket is pressed to a convex on the inserting part and the fastening ring will contract to fasten up the heating pipe by the fastening of outer nut, and there is also a convex on the ring to offer close coupling by mechanical re - press effect to prevent water from leaking in case of heat expansion

    在lg地熱管中的連接部位不僅閥門管套插入部分的凸起部位被機械作用壓密，而且隨著外部螺母被擰緊，使緊固環收縮，從而帶緊熱炕暖氣管，另外由於存在凸起部位，可通過機械作用進行再次壓密，因此可防止由於熱膨脹而引起漏水。
  4. Unibody design reduces outer leakage point, which prevent outside leakage more efficiently

    一體式設計，減少閥門外漏點，更有效防止外漏。
  5. Middle speed rotation, atomizing feeding, the liquid vale avoid leak through and high viscosity,

    特長：中速粘合混煉，霧化加液料，防滴漏耐高粘度液料閥， plc控制。
  6. Middle speed rotation, atomizing feeding, the liquid vale avoid leak through and high viscosity, plc control

    特長：中速粘合混煉，霧化加液料，防滴漏耐高粘度液料閥， plc控制。
  7. Torsion spring checks shall have reversible elastomer discs and in operation produce drip tight closure against reverse flow caused by backpressure or backsiphonage

    扭力彈簧止回閥應該配置雙向合成橡膠閥瓣，並且在工作時對于反壓力和反虹吸所產生的迴流具有防滴漏關閉性能。
  8. The reduced pressure detector assembly shall consist of two independent torsion spring check modules, a differential pressure relief valve located between and below the two modules, two drip tight shutoff valves, and required torsion spring check modules and relief valve shall be contained within a sleeve accessible single housing constructed from 304 ( sch 40 ) stainless steel pipe with groove end connections

    這種減壓檢測器總成應該包括兩個獨立扭力彈簧止回閥模塊，一個位於兩個模塊之間的下方的差壓安全閥，兩個防滴漏關閉閥，並且要求扭力彈簧止回模塊和安全閥應該放置在一個套筒內，要易於接近帶溝槽連接的304 （目錄40 ）不銹鋼管的單個外殼。
  9. The valve shall be constructed with a molded diaphragm separating the air inlet from the potable water supply to prevent spillage

    這種閥門結構應該是採用隔膜將空氣進口與飲用水供應分離開來以防止泄漏或溢出。
  10. If relief valve discharge due to a failure of the backflow preventer second check valve is a concern, a second flood protection - shutdown valve should be located immediately downstream of the backflow prevention assembly

    如果認為防迴流閥的第二止回閥的故障導致安全閥排放現象應該得到處理，則應該在防迴流閥總成下游立即安置第二堵漏-關閉閥。
  11. Plastics piping systems. valves for polyethylene piping systems. test method for leaktightness under and after bending applied to the operating mechanism

    塑料管道系統.聚乙烯管道系統用閥門.在操作機構上彎曲和彎曲后的防泄漏的試驗方法
  12. Smooth finished disc flats : these “ mate ” with seat flats to give a highly efficient seal ; prevents leakage into shaft areas

    光滑表面的閥板：這些閥板上的「配套」使得密封非常有效，防止泄漏到軸區域內。
  13. These fire - safe valves provide a bubble tight barrier on both upstream and down stream seats and eliminate possible product contamination or loss of fluids due to valve leakage

    這種防火安全閥門在上游和下游閥座提供氣密性屏障關閉性能，消除了由於閥門泄漏造成產品污染或流體損失的可能。
  14. These valves shall have ptfe seats and fpm seals for maximum service life and protection against external leakage

    這些閥門應該配置聚四氟乙烯閥座和fpm密封，使其使用壽命更長，更有助於防止外泄漏。
  15. Valves shall have glassfilled ptfe seals for positive shut - off and extended service - life and fpm seals for maximum protection against external leaks

    這些閥門應該配置玻璃填充聚四氟乙烯密封，關閉更靈活，使用壽命更長， fpm密封能夠更好的防止外泄漏。
  16. Diaphragm isolates the working parts of the valve from process medium for long life and leak - proof performance

    隔膜將閥門的工作部件與所處理的流體介質隔離開來，延長了使用壽命，改善了防泄漏性能。
分享友人
分享到 Line

分享到臉書