阻尼系數控制 的英文怎麼說

中文拼音 [zǔníxìshǔkòngzhì]
阻尼系數控制 英文
damping factor control
  • 阻 : 動詞（阻擋; 阻礙） block; hinder; impede; obstruct
  • 尼 : 名詞（尼姑） buddhist nun
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. The relationships of modal damping versus the stiffness of cables, the attachment height of damper and damping constant are obtained. with the optimal structural control method, a new approach to determine the optimal damping constant of viscous damper is presented. the first a few modal damping can be optimized simultaneously under the optimal damping constant of damper, which is more convenient than the existed design method

    4 、對拉索-粘性阻尼器系統的動力特性進行了研究，得到了拉索剛度、阻尼器安裝高度及阻尼系數等參數對拉索系統模態阻尼比的影響規律；根據最優控制原理，提出了一種確定阻尼器優化阻尼系數的方法，該方法確定的阻尼系數能保摘要證前幾階模態阻尼比得到整體優化，改進了現有的設計方法。
  2. Fist ly, use mass equivalent method to predigest the original rotor system. secondly, use transfer matrix arithmetic to have finished the relative program to calculate the critical speed of flexible multi - tray rotor bearing system by matlab language. thirdly. finish program the unbalance response using riccati - transfer matrix arithmetic and finity buck arithmetic. fourthly, answer to the high vibration of uncontroled system when cross the critical speed, come out to adopt changing clearance damper bearing to control the viberation

    本文對多柔盤轉子-支承系統的振動現象做了以下初步探索：用質量離散化方法把原轉子系統簡化；採用matlab語言編制了對傳遞矩陣法計算多柔盤轉子-支承系統的臨界轉速；用matlab語言對riccati傳遞矩陣法和有限元法編制了程序計算系統的不平衡響應；並針對其過臨界轉速時振動較大的現象，提出採用變間隙控制油膜剛度和阻尼，從而使原系統的在特定轉速（臨界轉速）的一段范圍內不平衡響應減小；並從被動控制與主動控制兩方面進行數值模擬，取的了較好的控制效果。
  3. According to the direction and damping characteristic of the torque produced by the magnetorquers, the three axis attitude control schemes of gravity gradient satellite and other satellite with damper is presented. the control coefficients are determined by the dynamic characteristics of geomagnetic intensity, so the attitude control precision is improved

    根據磁力矩在地磁場中的定向阻尼特性，提出了磁控重力梯度衛星和攜帶阻尼器的非重力梯度姿態控制規律，根據地磁場強度變化規律選擇控制系數，提高衛星的姿態控制精度。
  4. ( 4 ) parametric studies for control performance of the sma incorporated friction dampers in long - span canopy roof structures are carried out. by analysis, practical engineering suggestions are presented

    （ 4 ）系統進行了sma復合摩擦阻尼器在挑篷結構中的減振控制參數研究，通過對比分析，給出了實用性的工程建議。
  5. Then a simplified computational modal of damping isolation systems is established for a platform structure, and the relationships between the parameters of isolation layer and structural damping ratio, including their vibration - suppressed effect on the whole structure and the relative displacement of isolation layer are studied, and the simulation analysis under several representative load case of random wave force and earthquake affairs is performed. under random wave force, using complex mode theories, non - classically damp problems considering the interaction between the structure and wave, lying in deepwater, are studied. and the resolution solution of structural response are achieved. the results of calculating and analysing show that adding damping isolation to a jacket is an effective way to reduce vibration for offshore platforms

    針對某一典型平臺結構，建立了海洋平臺結構阻尼隔振體系簡化計算模型，進行了波浪荷載工況和地震工況的數值模擬，研究了隔振參數與結構阻尼比的關系以及它們對結構整體和隔振層層間相對位移的控制效果，運用復模態理論研究了位於較深水位的固定式導管架海洋平臺在隨機波浪力作用下考慮結構與波浪相互作用時運動方程中非經典阻尼的解耦問題，獲得了結構響應的解析解。
  6. The dynamics behaviors of the flexible jeffcott rotor system supported by unsteady short dynamic bearing are investigated. based on nonlinear unsteady - state dynamic n - oil film force model described by three functions the local stability of the periodic solutions with the controlling parameters, rotational speed ratio, imbalance amount, damping ratio and viscidity, are predicted by using the floquet multiplier. it is found that the period doubling bifurcation is caused by a certain imbalance amount and the hopf bifurcation is created by the lost stability of the oil - film

    研究了非穩態動載短軸承支撐的jeffcott柔性轉子系統的動力特性，基於可用三個函數表示動態油膜的非穩態非線性油膜力模型，將轉速比、不平衡量、阻尼比、粘度作為控制參數，利用floquet乘子預測周期解的局部穩定性，發現倍周期分叉是由一定量的不平衡引起的，而hopf分叉是由油膜失穩造成的。
  7. The electrical damping within the whole subsynchronous frequency range is calculated. the impacts of the unit interaction factor between hvdc and turbine generator, the dc power level, the firing delay angle and the parameter settings of hvdc controller on the have the potential danger of subsynchronous oscillation

    在整個次同步頻率范圍內，計算得到了系統電氣阻尼，並詳盡地分析了同步發電機與hvdc的耦合程度、直流輸送功率水平，換流閥觸發角大小以及控制器參數等因素對系統電氣阻尼的影響。
  8. In this paper, nonlinear static analysis methods, structural dynamic time history analyses based on structural state equation in hamilton system, multi - mode control theories of multiple tuned mass dampers, and semi active control laws of " on - off " are investigated

    本文分析和研究了結構靜力彈塑性分析方法、基於hamilton體系下結構狀態方程求解結構動力學問題的數值逐步積分方法、多重調諧質量阻尼器（ mtmd ）的多模態控制理論以及建築結構的半主動控制律。
  9. Taking the bending stiffness, cable sag and cable inclination into consideration, the space vibration control of the cables using the visco - elastic dampers in cable - stayed bridges is investigated by joining the center difference method and the state space strategy. both the maximum modal damping ration and the optimal damper size are obtained, then the practical suggestions are proposed for the design of the dampers. the space nonlinear vibration equations of the cable - damper system are derived, and a new hybrid method for solving the cable - damper system is presented by combing the newmark method and pseudo - force technology

    綜合考慮了拉索抗彎剛度、垂度的影響，研究了粘彈性阻尼器對斜拉橋拉索的空間振動控制，聯合中心差分方法及狀態空間法，得出了拉索麵內、外振動各階模態可能達到的最大阻尼比及相應的最優阻尼器系數，並對斜拉橋拉索的阻尼器設計提出了參考建議：考慮拉索抗彎剛度、垂度及幾何非線性，導出了索-阻尼器系統的空間振動非線性方程組，結合newmark方法及偽力（ pseudo - force ）方法，創新地提出了求解非線性方程組的雜交方法，根據拉索-阻尼器系統的阻尼特性，在各種荷載作用下，對索-阻尼器系統的非線性瞬態振動響應進行了研究，從系統響應的角度更加直接地驗證了阻尼器的控制效果。
  10. Base on review of existed study and application in suppressing cable vibration in the world, technique of mitigating cable vibration with viscous damper and mr damper has been investigated in this dissertation, and the main contents and progresses in form of summary are as following : 1 the motion differential equations of the cable - damper system are formatted, which take into account these factors, such as the inclined angle, sag, stiffness etc. coupling motion between cable and deck is studied with analytical and numerical method. numerical results show that large amplitude vibration of cable with beat rhythm will occur when exciting frequency of deck equals two times modal frequency of cable

    本文在對國內外斜拉索振動控制研究與應用現狀進行綜合評述、分析的基礎上，針對上述問題進行了深入研究，具體的研究內容和取得的成果包括： 1 、建立了斜拉索-阻尼器系統運動方程，對拉索與橋面的耦合振動作了分析和研究，數值結果顯示當橋面激振頻率等於某階拉索模態頻率的兩倍時，很小的初始擾動將引起拉索的大幅振動，並呈現拍振的特徵，與實測的拍振信號一致。
  11. Considering the nonlinear characteristic of dampers, computing simulation and analysis of the seismic response for high efficient damper suitable for muti - structure system ( hedms ) and system parameters " influence on control effect have been done

    考慮阻尼器的非線性滯回特性，對兩結構高效被動阻尼控制體系（ hedms ）的地震反應及體系參數對控制效果的影響進行了模擬分析。
  12. The unified power flow controller ( upfc ) is one of the most enterprising realizations of the idea of flexible ac transmission system ( facts ). having the ability of controlling most of the basic power system parameters, upfc can flexibly adjust the real and reactive power through the transmission line, damp the oscillation, and enhance the stability of power system and so on

    統一潮流控制器（ upfc ）是靈活交流輸電系統中最有代表性的成員，具備控制多種電力系統參數的能力，因而可以靈活地調節線路有功和無功功率、阻尼系統振蕩、增強電力系統的穩定性和提高輸電線路的傳輸極限。
  13. The paper studied controlling rotor vibration with the super - elasticity of sma and sfd, set up the new equation of sys tern vibration according to the stress - strain curve of sma in super - elasticity state, used the nonlinear theory and the dynamic stability theory to study the vibration of rotor controlled by sma, discussed the stability condition of the system, obtained the relationship of system parameters when bifurcation was appeared, supposed a method that improves the stability of rotor system and restrains vibration amplitude though changing parameters, and finally validated the effect of restraining vibration of the improved system through emulation

    摘要研究利用形狀記憶合金的超彈性和擠壓油膜阻尼器控制轉子振動，利用形狀記憶合金在超彈性狀態下的應力應變曲線，建立了新的系統振動方程，運用非線性理論和運動穩定性理論研究轉子在形狀記憶合金控制下的振動狀態，討論了系統的穩定性條件，獲得系統發生分岔時系統參數之間的關系；並提出了通過改變參數來提高系統穩定性和抑制振幅的方法，最後通過模擬驗證了改進后的系統振動抑制效果。
  14. The set of these eigenvalues can be regarded as the eigenvalues of primary system approximately. this method not only can control the scale of the block - decoupling subsystems, but also achieves the reduced - order eigenvalue calculation for multi - machine power system. so this method can avoid the dimension disaster in the qr and calculate all the eigenvalues of large power system with the effect of damping windings considered

    這一方法可以控制分塊解耦子系統的規模，實現多機系統特徵值的降階計算，避免特徵值qr演算法的「維數災難」 ，同時為採用計及發電機阻尼繞組作用的詳細模型計算大型電力系統的全部特徵值、提高電力系統小擾動穩定分析的準確性提供了一種方法。
  15. For the research of the damping control strategy one type of controllable damper, magnetico - rheological ( mr ) damper, was constructed and tested, the damping force and displacement characteristic curves, the damping force and velocity characteristic curves are obtained, so that the damping force and voltage ( current ) model, or the damping coefficient and voltage ( current ) model can be further obtained

    通過特性試驗，得到示功特性、速度特性，經轉換得到阻尼器的阻尼力? ?電壓（電流）模型和阻尼系數? ?電壓（電流）模型。這樣在研究中，可以採用開環控制方式或力反饋控制方式實現阻尼力的控制。
  16. The micromechanical comb - capacitive accelerometers fabricated by bulk silicon micromachining process are widely used for having simple process, small temperature coefficient, good stability and easily controllable damping coefficient

    用體硅微機械工藝製作的梳齒電容式傳感器有製作工藝簡單、溫度系數小、穩定性好、阻尼系數容易控制等優點，因而應用廣泛。
  17. In chapter three, the passive vibration control of a smart cantilever beam with piezoelectric shunt damping system is studied theoretically. in this chapter, the mechanical impedance of piezoelectric shunt damping system is analyzed, and the parameters of the rlc piezoelectric shunt circuit are optimized via transfer function of the piezoelectric shunt damped beam in order to optimize the vibration damping effect

    研究了利用壓電分流阻尼系統進行壓電智能懸臂梁被動振動控制的方法，分析了壓電分流阻尼系統的機械阻抗，並通過傳遞函數方法對rlc串聯壓電分流諧振電路元件的參數進行了優化，以使壓電分流阻尼系統的阻尼效果達到最優。
  18. Utilizing backstepping procedure, general expression of control strategy for hvdc converters is acquired. the control strategy can restrain the nonlinear uncertainty through injection of nonlinear damping terms in virtual controllers. the proposed decentralized adaptive control scheme guarantees that all the signals in the closed - loop system are bounded in the presence of high order interconnections and bounded disturbances

    設計中引入自適應非線性阻尼項來抑制系統非線性不確定參數和未知有界干擾的影響，同時採用反演設計方法來克服控制器設計的復雜性，最後獲得高壓直流輸電系統換流站的分散魯棒自適應控制策略的一般表達式，並提供了整個系統的穩定性證明。
  19. Considering the randomness of physics parameters of structural material, geometric dimensions, damping, loads and closed loop control voltage respectively or simultaneously, the analytic model of the stochastic structure under random forces are built. the solving methods are proposed. the computational expressions of the numerical characteristic of the structural dynamic response are developed

    2 、考慮壓電智能桁架結構物理參數、幾何參數、結構阻尼和外荷載、閉環系統控制電壓分別或同時為隨機變量，構建了結構在隨機力作用下的動力響應分析模型，提出了求解方法，推導出結構動力響應隨機變量的數字特徵計算表達式，通過算例驗證了所建模型和所提求解方法的正確性和有效性。
  20. A novel strategy combined the fuzzy logic of linear multivariable feedback control to design a controller of statcom to meet the multi - objective demands of power systems is also proposed in this dissertation, and the controller is designed with this strategy, because of variational element, nonlinearity and multi - objective controlling demands of statcom, this paper designs the controller respectively aimed at continuous linear control for voltage maintaining, oscillation damping, improving the transient stability

    根據電力系統變參數、非線性以及對控制要求多目標的特點，本文針對維持系統節點電壓、阻尼系統振蕩、提高系統暫態穩定性能等不同控制目標分別設計了控制器，然後將模糊邏輯和多狀態線性反饋相結合，提出了一種能滿足電力系統多目標要求的控制方法，並用該控制方法為statcom設計了控制器。
分享友人
分享到 Line

分享到臉書