降壓線圈 的英文怎麼說
中文拼音 [jiàngyāxiànjuān]
降壓線圈
英文
diminishing coil-
We can use the mm5 model in definite time, definite area weather forecasting. we conclude that : : the moving route of this necw in its developing progress was direct - south along latitude, the cold air is rough, and just this made the rough vertical velocity ; the necw southern moving and conflicting with the west pacification sub - tropical high makes rough jet steam. the plenty south - west warm and wet air made by the jet stream gave the rainstorm demanded vapor ;. the rough vertical velocity by jet stream is a main reason in this rainstorm ; the mm5 model uses four - direction analysis data as its input, this avoids some errors occurred in observe and transfer, thus made the result more useful
綜合分析認為: ( 1 ) 、這次冷渦在其發生發展過程中,其移動路徑是沿經圈直線南壓,攜帶的冷空氣勢力較強,形成槽后較強的垂直運動; ( 2 ) 、西太平洋副熱帶高壓偏北位置與東北冷渦南壓形成的急流軸,把源源不斷的西南暖濕氣流輸送到遼西地區,也就是急流軸的左前方位置,為這次暴雨的產生提供了充足的水汽來源; ( 3 ) 、低空急流不但為暴雨輸送水汽,其造成的較強的垂直環流也是產生強降水的一個主要原因; ( 4 ) 、 mm5模式以四維同化資料作為初始場,最大限度地避免了觀測誤差可能造成的積分不穩定,提高了模擬結果的參考價值。If we like to obtain the narrow linewidth parametric beam output, applying soft apertures to input pump beam is helpful, but it will also
如果想獲得窄線寬輸出,採用軟光圈直接輸入泵浦光將有助於壓縮輸出參量光的線寬,代價是轉換效率降低。Results of experiment b demonstrate that a convergence zone of wind vector and water vapour with dense pressure gradient is formed alone the coast after tc ' s outer circulation encountering land, which results in more precipitation
試驗b的結果顯示,熱帶氣旋外圈環流與陸地接觸後到中心登陸前後,沿海岸線一直存在一條氣壓梯度相對密集的風矢量、水汽輻合帶,引起該處降水增多。There is no any partial discharge, any cracks and reduced insulation level on sg b0 10 series transformers under operation in whole effective life term due to the structures of windings with keep improving design and vacuum pressure impregnating technology
10系列非包封線圈乾式變壓器在運行條件下無局部放電產生。並且在整個壽命期內,無任何裂和絕緣水平下降現象。General motors, transformers, coils of copper enameled wire sectors such as manufacturers, because the cost of raw materials, huge pressure aluminum instead of copper enameled wire enameled wire forced to reduce costs, enameled wire and aluminum welding problem has become impossible for manufacturers restructuring in the region
廣大電機、變壓器、線圈等相關行業生產廠家因為銅漆包線原材料巨大的成本壓力,被迫採用鋁漆包線代替銅漆包線以降低成本,而鋁漆包線的焊接問題成了制約廣大生產廠家轉型的瓶頸。分享友人