陶瓷壞 的英文怎麼說
中文拼音 [táocíhuài]
陶瓷壞
英文
ceramic machinery-
The damage of the transducer was avoided, so the ability of over - loading can be improved highly. in order to acquire a good hermetic seal between the diaphragm and the base plate, two sealing methods were used, namely, compound method and crystallite method
通過試驗對比，確定了介質腔的厚度，使陶瓷膜片在過載時與基座接觸，從而避免了傳感器的過載損壞，使傳感器的抗過載能力大大提高。研究了復合法和結晶法兩種封接方式，使陶瓷基座與膜片達到良好的匹配封接。Standard test method for adhesion strength and mechanical failure modes of ceramic coatings by quantitative single point scratch testing
用定量單點劃痕試驗測定陶瓷塗層粘結強度和機械損壞類型的標準試驗方法With the material dynamic constitutive equation including damage and the effect of stain rate the predictable formula about ballistic limit velocity of fiber composite target. secondly based on the damage feature about ceramic / fiber composite target caused by impact load, analysis model about defense performance of ceramic / composite material target is formed and the predictable formula about ballistic limit velocity is also given. lastly using the reflection and projectile theory of stress wave the paper discusses the design of ceramic / composite material target, optimizes the design of double layer ceramic / composite targets, gains optimal coefficient under certain area density and discusses the variety relationship of area density and thickness with optimal coefficient u nder some ballistic limit velocity 3
首先，分析了纖維類正交鋪層復合靶板在沖擊載荷作用下的損傷破壞機理，結合包含損傷和應變率效應的材料動態本構方程，建立了纖維復合材料板彈道極限速度的預測公式；其次，根據陶瓷/纖維材料復合靶板在沖擊載荷下的破壞特點，建立了陶瓷/復合材料靶板抗彈性能分析模型，給出了彈道極限速度預測公式；最後，利用應力波反射和透射理論討論了陶瓷/復合材料靶板的設計問題，對雙層陶瓷復合靶板的優化設計進行了分析，給出了在一定面密度下的最佳優化系數，討論了一定彈道極限速度下的面密度和厚度隨優化系數的變化關系。As part of the renovation, the hotel ‘ s intricate terra cotta trim was painstakingly cleaned, and damaged pieces repaired with glass - reinforced concrete castings and finishes matched to the originals
作為改建的內容之一，該旅館錯綜復雜的陶瓷磚裝飾部分，被人們煞費苦心地清理干凈一些損壞的部分則採用玻璃（纖維）增強混凝土現澆或預制而成，其修復程度可以與原件相媲美。Microstructural change and thermal shock performance of metal / ceramic graded thermal barrier coatings in thermal shock experiments were studied by scanning electron microscope and energy - dispersive spectrometry. the results showed : 1 ) metal microstructure kept intact while ceramic microstructure had been destroyed ; 2 ) thermal shock performance of coatings was interrelated with its function to relax residual stresses, therefore thermal shock performance of gradient thermal barrier coatings was better than that of terraced thermal barrier coatings ; 3 ) thermal shock performance was concerned with metal content in metal / ceramic thermal barrier coatings, which would be improved when metal content was increased
利用掃描電子顯微鏡和能譜成分分析技術研究了金屬/陶瓷梯度熱障塗層在熱震過程中的顯微組織變化及其抗熱震性能.結果表明： 1 ）金屬顯微組織保持完好，陶瓷顯微組織有明顯的破壞； 2 ）塗層抗熱震性能與其熱應力緩和功能密切相關，梯度熱障塗層比階梯熱障塗層具有更高的抗熱震性能； 3 ）金屬/陶瓷熱障塗層抗熱震性能與其中金屬相含量有關，金屬相含量增加可改善塗層抗熱震性能But calcium phosphate ceramic with high porosity is such brittle and low toughness that it ca n ' t fit to bone tissue engineering. in order to provide appropriate scaffolds for bone tissue engineering, calcium phosphate was combined with plla to prepare porous material
但磷酸鈣多孔陶瓷材料脆性大，在生理環境中的疲勞與破壞強度不高，尤其在濕環境下斷裂韌性很低，不能制得滿足組織工程要求的高孔隙率，力學性能較高的支架材料。Thermal and welding residual stress often produces in the proceeding of the electronic package, the residual stress release and thermal deformations of the microelectronics will reduce the assemble intensity between the chip and package, and then debase the electrical performance of the assemble circuit, numerous thermal cycling will lead to thermal fatigue or thermal failure of the microelectronics
電子封裝器件在生產的工藝過程中，往往會產生熱殘余應力以及焊接殘余應力，殘余應力的釋放作用及器件在使用過程中的熱變形，會降低集成電路晶元與封裝體的結合強度，進而降低集成電路的電性能，反復的熱循環，將導致器件的熱疲勞失效，嚴重時可導致矽片或陶瓷片破裂，使整個器件遭到破壞。Progressive fragment modeling of the failure wave in ceramics under planar impact loading
沖擊壓縮下陶瓷材料中的破壞波模型分享友人