離心式轉數計 的英文怎麼說

中文拼音 [líxīnshìzhuǎnshǔjì]
離心式轉數計 英文
centrifugal tachometer
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 轉 : 轉構詞成分。
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 離心 : 1 （不是一條心） be at odds with the community or the leadership2 （離開中心） centrifugal; eccen...
  1. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  2. We analyzed the centrifugal compressor ' s loading types, made certain the shift gears running work conditions of the centrifugal compressor, and putted forward the shift gears running energy - saving ratio calculational methods of centrifugal compressor, and discussed the centrifugal compressor ' s anti - surge conditions, and getted set the running ratating speed optimized mathematics model of centrifugal compressor

    分析了離心式壓縮機的負荷類型，確定了離心式壓縮機變速運行工況，提出了離心式壓縮機變速運行節能率計算方法，討論了離心式壓縮機的防喘振條件，建立了離心式壓縮機運行轉速優化的數學模型。
  3. And the theoretical a nalyses done in this paper are listed below : first, the experimental data on the members of varied parameters under torsion demonstrate the general rule of the deformation while the tubular is under torsion. the paper establishes three phases of the deformation of the tubular under torsion, namely, the elastic deformation, the elastic - plastic deformation, and ultimate failure. through regression analysis, a simplified method is proposed for calculating the capabilities of the tubular under elastoplastic torsion, and the formulary for bearing value, is also recommended as a reference in engineering design

    本文根據不同參數的構件受扭性能試驗結果，研究了該結構受力變形全過程的基本規律，提出了受鈕全過程的三個工作價段，即彈性變形階段，彈塑性變形階段和極限破壞階段，經分析回歸得到扭轉全過程彈塑性的簡化分析方法及承載力計算公式，可供工程設計參考；同時根據本文的彎扭試驗結果以及對離心鋼管混凝土構件進行的理論分析，推導了彎扭試驗相關承載力的關系。
分享友人
分享到 Line

分享到臉書