電刷電阻 的英文怎麼說

中文拼音 [diànshuādiàn]
電刷電阻 英文
brush resistance
  • : Ⅰ名詞1 (有電荷存在和電荷變化的現象) electricity 2 (電報) telegram; cable Ⅱ動詞1 (觸電) give...
  • : 刷構詞成分。
  • : 動詞(阻擋; 阻礙) block; hinder; impede; obstruct
  • 電阻 : (物質阻礙電流通過的性質) resistance; electric resistance (電路中兩點間在一定壓力下決定電流強度...
  1. For the bldcm which has a pseudo - sinusoidal back - emf waveform, this dissertation presents a svpwm control method using six discrete position signals for minimizing the torque ripple. the main aspects for the implementation of this method are analyzed, including the initial orientation of the voltage vector, reasonable choice of the impedance angle and the advance commutation angle, and estimation of the successive rotor positions

    針對反動勢類似正弦的準正弦波反動勢無直流動機,本文提出一種基於六個離散位置信號的自同步svpwm (壓空間矢量法)控制方法,用以削弱磁轉矩脈動,分析了實現這種方法的主要控制環節,包括起動時壓空間矢量的初始定位,抗角與流超前角的合理選擇以及連續轉子位置的估計等。
  2. This paper gives the fundamental equation of electric circuit of switched reluctance generator ( srg ). the phase flux linkage, indutance and phase current of srg are discussed based on unsaturated magnetic circuit

    給出了開關磁機的相路基本方程,分析了基於不飽和磁路條件的相磁鏈、相感和相流。
  3. On the base of the development of thick film pastes technology, ru - based thick film resistor pastes have been studied due to select conductive phase and inorganic binder. state - of - the - art techniques such as rolling, screen printing and sintering were used for sample preparation. effects of ingredients, printing parameters and sintering parameters, microstructure on the properties of thick film resistor ( trf ) have been analyzed with xrd, sem, dsc and electrical tests

    本文在跟蹤國內外厚膜漿料技術發展的基礎上,以釕酸鉍/銀系厚膜漿料為研究對象,通過選用合適的功能相和無機粘結相成分,以三輥軋制、絲網印和高溫燒結等制備工藝為技術特徵,採用xrd 、 sem 、 dsc等分析方法和性能測試手段,系統的研究了漿料中各相的成分配比、制備工藝參數,以及膜層微觀結構對厚膜性能的影響規律。
  4. Avoid drawing any current from the wiper of a potentiometer. the resistance of the wiper contact will cause problems ( local heating, noise offsets etc

    避免從位器的弧處提取流。弧的接觸抗會產生問題(局部溫升,噪聲偏移等等) 。
  5. Printed boards and printed board assemblies - design and use - part 1 - 2 : generic requirements - controlled impedance

    路板和印路板組件.設計和使用.第1 - 2部分:一般要求.控制
  6. In order to improve the circuit ' s input impedance, which is affected by insulating resistance of electrode leading wire, terminals and printed circuit board, electrode is connected to the meter through insulating wire of high impedance which is directly welded in the printed circuit board with insulating ring. the deviation of electrode is corrected by software and the algorithm is given

    使用高絕緣線連接極,並將高絕緣線直接焊在加有絕緣環的印線路板上,從而消除極引線、接線端子和印線路板漏對放大路輸入抗的影響;軟體校正極偏差,並給出校準演算法。
  7. Test method for physical - chemical properties of electrical carbon product. connection electrical resistance of brush flexible connection

    炭製品物理化學性能試驗方法.體與軟接線聯接處的聯接
  8. Equivalent circuit and stead - state behavior of doubly fed brushless reluctance machine

    雙饋磁機的等效路與穩態特性分析
  9. Pm flux switching machines contain the merits of both switched reluctance machine and pm machine, such as the simple structure, high torque density and efficiency, as well as the flux - weakening capability

    摘要永磁開關磁鏈機兼具開關磁機和永磁無機的優點,結構簡單、轉矩和能量密度大、效率高,而且具有良好的弱磁能力。
  10. Test method for determining the electrical resistivity of a printed conductive material

    測定印傳導材料率的試驗方法
分享友人