電流差動 的英文怎麼說

中文拼音 [diànliúchādòng]
電流差動 英文
current differential
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 電流 : current; galvanic current; electric current; electricity; current flow電流保護裝置 current protec...
  1. A white led driver circuit is presented in this paper. the circuit drives up to four white leds with regulated constant current for uniform intensity. by utilizing proprietary adaptive 1x / 1. 5x modes and ultra - low - dropout current regulators, it maintains the highest possible efficiency over the full 1 - cell li + battery input voltage range

    整體電路以恆定電流驅動4隻白光led ，利用1倍/ 1 . 5倍分數型電荷泵和低壓差電流調節器，在整個鋰電池供電電壓范圍內保持最高的效率，並使四個白光led獲得均勻的亮度。
  2. As a result, the electromagnetic field intensity is changed accordingly and fluctuating current in the damper coil is created. damping force is mostly produced because of the phase difference between fluctuating current and displacement of rotor. the formulas of fluctuating current and damping coefficient are deduced theoretically, and the calculated results are consistent with the experimental results

    通過分析發現電磁阻尼器線圈內由於轉子渦動時變化的磁場而產生的波動電流與轉子位移間的相位差是產生阻尼的主要原因，推導了波動電流、阻尼系數的計算公式，並通過實驗展示了被動式電磁阻尼器的阻尼效應。
  3. Dead angle of differential currents is measured when realizing the transformer differential protection based on the dead angle

    在間斷角原理變壓器差動保護中，需要測量差動電流導數波形的間斷角。
  4. Using the color sensor as the navigation sensor, with mcu for control centre, the robot is drived and change direction by the differ direct current motor

    用顏色傳感器作為導航傳感器，以單片機為控制器，直流電動機實現驅動和差動轉向。
  5. The mutual inductor of electric current and voltage mutual inductor play an important role in relay protection. prevent from ct differential to protect and miss movement an important subject that the generatrix is protected on the saturation, put forward two electric current pass zero hour linear to spread person who become put into differential to protect in ct in recent years, avoid ct saturation district, can judge the bus bar trouble correctly

    但是在母線區外發生短路故障（特別是故障電流含有大量非周期分量）時， ct會出現飽和現象， ct飽和后，不能正確地傳變一次側電流，從而使二次電流發生嚴重畸變，產生很大的差電流，這樣就容易引起誤動作。防止ct飽和時差動保護誤動作一直是母線保護的一個重要課題，近年來提出的在ct二次電流過零時的線性傳變區投入差動保護，避開ct飽和區，能對母線故障做出正確判斷。
  6. The bus differential protection based on instantaneous values of currents is the most useful scheme nowadays. but it is easy to be influenced by current transformer saturation and to make misoperation

    目前微機保護最常用的方法是電流瞬時值差動保護，這種方法受電流互感器（ ta ）飽和的影響而容易誤動。
  7. Neural network control is an important mode of intelligent control, and it is widely used in branches of control science, first, the architecture and the learning rule ( error back propagation algorithm ) of multiplayered neural network which is widely used in control system are presentedo especially, the paper refers to the architecture of diagonal recurrent neural network and its learning algorithm - - - - - recurrent prediction error algorithm because of its faster convergence with low computing costo next, before introducing the neural network control to the double close loop dc driver system, the controllers of current and velocity loop are designed using engineering design approach after analysis of the system, simulation models of the system are created

    神經網路控制是智能控制的重要方式之一，它廣泛應用於自動控制學科各個領域。本文首先敘述了控制系統中常用的多層前饋網路結構及演算法（ bp演算法） ，特別提及了能夠較好描述系統動態性能的對角遞歸神經網路和在用遞推預報誤差演算法訓練drnn時取得了較快的收斂速度。其次，應用工程方法分析設計了tf - 1350糖分離機的電流、轉速雙閉環直流調速系統的控制器，作為引入神經網路控制的設計基礎，並建立了系統的模擬模型。
  8. Unbalanced current generated in differential protection of main transformer and its countermeasure

    主變差動保護不平衡電流產生及應對措施
  9. By comparing and analyzing the advantages and disadvantages of three kinds of voltage reference circuits, type of current density ratio compensation 、 weak inversion type and type of poly gate work function, a cascode structure of type of current density ratio compensation is chosen to form the core of voltage reference circuit designed in this paper. applying the negative feedback technology, an output buffer and multiply by - 2 - circuits are designed, which improve the current driving capability

    然後通過比較和分析電流密度比補償型、弱反型工作型和多晶硅柵功函數差型三種帶隙電壓基準源電路結構的優缺點，確定了電流密度比補償型共源共柵結構作為本設計核心電路結構，運用負反饋技術設計了基準輸出緩沖電路、輸出電壓倍乘電路，改善了核心電路的帶負載能力和電流驅動能力。
  10. At present, differential protection is often used as the main protection for traction transformers. however, the existing of certain factors, such as magnetizing inrush, over - excitation, ct saturation and mismatching of ct ratio, will result in that it is hard to distinguish state current and fault current, and differential protection misoperation or maloperation, then secure operation of electric railways system will be threatened

    目前，牽引變壓器通常採用差動保護作為主保護，但是在某些因數的影響下差動保護並不能準確的區分牽引變壓器內部故障或非內部故障，如故障電流與變壓器處于勵磁涌流、過勵磁， ct飽和及ct變比不匹配等情況下的狀態電流就很難準確的區分，可能造成保護誤動或拒動，從而危及整個鐵道電氣化系統的安全運行。
  11. Ser - elektronik gmbh offer to you electric meter and signalling devices in addition also info on electricity supply meters

    在以下范圍內我們提供產品和服務：差動、差別、差速器、測量工具和電流繼電器以及模仿或電表。
  12. The safety of transmission line plays a important role in power system safety it is not only the requirement of ensure supply power reliability, but also the necessary precondition of enhance power system stabilization, to remove faulty line quickly and accurately, also keep non - faulty line continuous work when some transmission line faults current differential protection is a kind of simple, reliable and good - selective protection manner to any variety of transmission lines, power system development needs current differential protection apply to transmission lines, moreover the advancement of electric and communication technology enable current differential protection apply to transmission lines firstly, the paper discusses, analyses the research and application transmission line protection in detail, compare the principle and realistic presupposition of general line pilot protections secondly, because conventional current vector differential protection are influenced easily by load current and transitional resistance, in order to at the same time quicken protection act, the principle and criterion include work characteristic of differential protect based on fault component sampled values are studied, results shows that differential protect based on fault component sampled values excels general vector current differential protection in reliability, sensitivity and anti - saturation of current transformer in addition, synchronous current sampling methods at all terminals of line is analyzed and estimated lastly, the principle and criterion. also device design about current sampling values differential protection based on optical fiber communication, which apply to short transmission lines are concretely investigated,

    基於基爾霍夫定律的電流差動保護無論對於何種形式的輸電線路都是一種簡單、可靠、選擇性強的保護形式，電力系統的發展使得電流差動保護應用於線路保護成為需要，而電子、通信技術的發展使得電流差動保護應用於輸電線路成為可能。首先，本文對目前線路保護的研究和實際應用情況進行了討論和分析，比較了常用線路縱聯保護的實現原理和實現條件及優缺點。其次，針對常規相量電流差動保護易受正常負荷電流和故障過渡電阻影響的缺點，同時為加快差動保護的動作速度，對基於故障分量瞬時采樣值電流差動保護的原理、判據、動作特性等作了討論和分析，結果表明基於故障分量瞬時采樣值電流差動保護在可靠性、靈敏度、抗電流互感器飽和方面明顯優于常規相量電流差動保護，對電流差動保護各端的同步采樣方法和數據通信也進行了分析和評價。
  13. Through analysising the characteristics of the power system with floating neutral point deeply, the paper puts forward a new plan of single - phase to ground fault line selection on the base of s ' s signal injecton method and gives the hardware and software design. in this design, the high speed sampling and data processing is carried out through using dsp processor ; the large electrice current is drived through the application of a high - performance audio power amplifier and transformer ; the communication between host computer and detectors is realized through rs485 bus technology ; the difference multilevel frequency - selected amplifier is designed and the feeble signal of space is sampled on the base of the theory of magnetic induction ; the interface between dsp and exterior chip and rs485 interface logical is designed through using fpga ; the using of lcd module and keyboard interfacing chip makes the interface between human and machine ; the programme of host computer and detectors is designed through using blocking design method

    在本設計中，採用高速的dsp處理器，實現了對故障特徵信息的高速採集與處理;採用大功率的功放晶元與變壓器配合的方法，實現了大電流信號的驅動輸出;採用485總線技術，組建了裝置主機與多探測器之間的主從式通訊網路，實現了多干擾條件下裝置主機與多探測器的可靠通訊;設計了差分式多級選頻放大電路，採用磁感應的方法實現了對空間微弱信號的接收;利用fpga技術，實現了控制器與多外設的介面及數字信號的串並轉換;採用了先進的lcd液晶顯示模塊及鍵盤介面晶元，設計了人機信息交互的介面;採用了模塊化的軟體設計方法，開發了裝置主機及探測器的軟體程序。
  14. In order to solve the existing ct saturation problem which is met in current differential principle, this paper bring forward the new method to discriminate ct ' s saturation based on bd wavelet transformation

    針對電流差動原理中遇到的ct飽和的問題，提出了基於bd小波變換識別ct飽和的新方法。
  15. This paper analyzes detailedly the principles on distributed busbar protection - current instantaneous value differential method, impedance method, and put forward the new method of current fault component phase method, then compares with these methods

    本文詳細分析了分散式母線保護中的原理?瞬時值電流差動法、阻抗法，提出了電流故障分量相位法的新方法，將這幾種方法進行比較。
  16. Even if the fault spread from external fault zone to internal fault zone, the differential protection can avoid misoperation. main criterion of protection is composite - percentage current differential algorithm according to every sampled value, which can accelerate the protection ' s trip, reduce large amounts of calculation and have strong stability to ta saturation

    本文採用基於采樣值的比率制動式電流差動保護演算法作為保護的主判據，可以明顯提高保護動作速度和減少計算量；具有較強的抗ta飽和能力，在區內故障時無制動，區外故障時有極強的制動特性。
  17. The device can protect start - up status and running status of asynchronous motors by differential protection, over current protection, negative - sequence current protection, zero - sequence current protection, inverse time current protection, under - voltage protection and so on, can measure every kind of electricity, and can process the function of telecontrol, telemetering and telecommunication

    其依靠電流差動、速斷、負序過流、反時限、零序過流和低電壓等保護方法實現了片電動機的運行、啟動和自啟動過程進行保護，並實現各種電量的計量，同時具有遙控、遙測、遙信的功能。
  18. Abstract : in this paper, the setting scheme of the current differential protection based on sampled values using fault component is investigated. the setting schemes of the resistance coefficient and the least trip differential current are discussed in detail. the probable protection setting values for the hv transmission lines are described. it testifies the feasibility for the applications of the protection to the hv transmission lines

    文摘:對基於故障分量的采樣值電流差動保護制動特性曲線的整定方法進行了研究，詳細討論了其制動系數和最小動作電流的整定方法，同時對該保護在輸電線路中的應用進行了初步的估算，說明了該保護的優異性能。
  19. The thesis is focus on the research of the optical - fiber differential current protection that can adapt to the rapidly changing power grid. it mainly contains the following four parts : ( 1 ) theoretical analysis of some operation criterions and some factors that influence the operation of the differential protection. ( 2 ) simulation of a 500kv transmission line using emtp software

    其主要內容是： （ 1 ）對影響差動保護靈敏度的各種因素和不同的電流差動保護判據進行了理論分析； （ 2 ）用emtp模擬軟體對差動判據進行了數據模擬，並用matlab對輸出結果進行了詳細的可視化分析； （ 3 ）分析、比較了國內外縱差保護的數據采樣同步方法； （ 4 ）對判據進行了實際的編程實現和動模模擬。
  20. Become a kind of new electronics circuit - current - mode circuit. it is replacing the traditional design method of the voltage - mode in the high frequency high - speed signal processing realm 。 this thesis mainly discussed the modified second - generation current conveyors based on the current - mode kinds of new cuicuit components, they are stronger modified standard current - mode parts in fuctions on this foundation. mainly including the modified differential difference current conveyor ( mddccii ) 、 the fully balanced second generation current conveyor ( fbccii ) 、 ( full balances ) four - terminal floating nullor ( fbftfn ) and the current differencing buffered amplifier ( cdba ), they are all function very strong standard current - mode parts, they all can provide some circuit functions of better than general operation amplifier, because they have the voltage importation and the current importation, therefore use it since can carry out the voltage - mode signal processing circuit expediently, can also carry out the current - mode signal processing circuit expediently, and have to increase the benefit bandwidth to accumulate more widely than the voltage - mode, but have their advantages more according to the current - mode filter of the modified current conveyor, because it constitutes in brief, the filter wave function is stronger and they are better than in general use operation amplifier of many advantages, be easy to composing for example 、 high speed 、 frequency bandwidth 、 the power supply voltage requests low 、 consume small, the impedance is different from etc. advantages, otherwise they have biggish dynamic range, and flexible circuit synthesize, so they are the best active parts

    從第二代電流傳輸器ccii入手，重點研究了以下幾種改進型的第二代電流傳輸器:改進的差動差分電流傳輸器mddccii 、全平衡第二代電流傳輸器fbccii 、多輸出四端浮地零器ftfn 、全平衡四端浮地零器fbftfn 、電流差分緩沖放大器cdba的電路結構及其模型。然後在此基礎上系統地研究了基於這幾種改進型的第二代電流傳輸器的濾波器的設計方法，主要方法和結果如下:利用mddccii設計了差分式連續時間電流模式低通、帶通濾波器;電流模式跳耦結構考爾低通濾波器;利用fbccii設計了帶通二階節濾波器及電流模式雙二階通用濾波器;設計了基於多輸出端ftfn的電流模式二階通用濾波器電路;通過數字化開關選擇的基於fbftfn的電流模式通用濾波器;設計了基於最少個數電流緩沖放大器（兩個cdba ）的多功能通用電流模式濾波器及其在非理想因素情況下分析。設計濾波器的主要方法是採用級聯設計、運算模擬（信號流圖法）和反饋設計（跳耦法） 。
分享友人
分享到 Line

分享到臉書