電纜彎曲半徑 的英文怎麼說

中文拼音 [diànwānqūbànjìng]
電纜彎曲半徑 英文
cable bend radius
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 纜 : Ⅰ名1. （拴船用的鐵索或多股粗繩） cable; hawser; mooring rope 2. （擰成多股的似纜物） thick rope; cable Ⅱ動詞（用繩索拴船） cable
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 半 : Ⅰ數詞1 （二分之一） half 2 （在 中間的） in the middle; halfway 3 （比喻很少） very little; the l...
  • 徑 : Ⅰ名詞1 （狹窄的道路; 小路） footpath; path; track 2 （達到目的的方法） way; means 3 （直徑的簡稱...
  • 電纜 : cable; electric cable
  1. 3. the permitted bending semidiameter is not less than four times of cable outside diameter

    3 .電纜允許彎曲半徑不小於電纜外徑的4倍
  2. 2. when installing, the permitted bending semidiameter is not less than four times of cable outside diameter

    2 .敷設時電纜的允許彎曲半徑應不低於電纜半徑的4倍
  3. Permissible bending radius : not less than 6 times of overall diameter for unarmored cable ; not less than 12 times of overall diameter for armored or screened cable ; not less than 6 times of overall diameter for screened flexible cable

    推薦允許彎曲半徑：無鎧裝層電纜應不小於電纜外徑的6倍；有鎧裝層或屏蔽層結構的電纜應不小於電纜外徑的12倍；有屏蔽結構的軟電纜應不小於電纜外徑的6倍。
  4. Permissible min. bending radius : no less than 6 times of the completed cablediameter in case of unarmoured cable ; no less than 12 times of the completed cable diameter in case of armoured or copper tape screened cabel ; no less than 6 times of the completed cable diameter in case of screened flexible cabel

    3電纜的允許彎曲半徑：無鎧裝層的電纜，應不小於電纜外徑的6倍；有鎧裝層或銅帶屏蔽結構的電纜，應不小於電纜外徑的12倍；有屏蔽層結構的軟電纜，應不小於電纜外徑的6倍。
  5. While installation the ambient temperature should not be lower than 0, and the bending radius radius should not be less than 10 times of outer diameter of cable

    敷設電纜時的環境溫度不低於0 ，最小彎曲半徑應不小於電纜外徑的10倍。
  6. When installing crooked radius aluminium bring or aluminum pipe should smaller than cable 30 times of external diameter, unless it install when not transporting it should handle with care, can t twist, can t not when not piling up heavy pressure, should keep dry, ventilate, not moist while preserving

    安裝時彎曲半徑鋁帶或鋁管的應不小於電纜外徑的30倍，安裝運輸時應輕拿輕放，不能扭曲，堆放時不能重壓，存放時應保持乾燥、通風、不潮濕。
  7. Test method for static minimum bending radius for coaxial trunk, feeder, and distribution cables

    共軸總線饋電線和配線電纜用靜態最小彎曲半徑的試驗方法
  8. Bending radius : cable with no shielded layer not smaller than 6 times of its outer diameter ; otherwise, not smaller than 12 times

    最小彎曲半徑：無鎧裝層電纜應不小於電纜外徑的6倍帶鎧裝層電纜應不小於電纜外徑的12倍
  9. The min curving radius : copper tape screened cable and steel tape armored cable should be at least 12 times the outer diameter. other cable should be at least 6 times the outer diameter

    電纜最小彎曲半徑：銅帶屏蔽電纜、鋼帶鎧裝電纜不小於外徑的12倍，其它電纜不小於電纜外徑的6倍。
  10. Bending radius : cable with no shielded layer not smaller than 10 times of its outer diameter ; otherwise, not smaller than 12 times

    最小彎曲半徑：非鎧裝電纜不小於電纜外徑的10倍鎧裝電纜不小於電纜外徑的12倍
  11. The bending radius of a three - core cable should not less than 15 times of the cable diameter

    5 、電纜彎曲半徑：三芯電纜不小於電纜外徑15倍；單芯電纜不小於電纜外徑20倍。
  12. Working temperatureof 65, its smallest bending radius is six times the size of cable diameter. the yellow sheath calbe shoulo not be exposed in the sun shine long time

    電纜導體的長期允許工作溫度65 ，電纜的最小彎曲半徑為電纜直徑的6倍。黃色護套電纜不得在日光下長期暴露。
  13. The allowed working temperatureof the core is 65 its smallest bending radius issixtimes the size of cable diameter. the yellow sheath calbe shoulo not be exposed in the sun for long

    線芯長期允許工作溫度65 ，電纜的最小彎曲半徑為電纜直徑的6倍。黃色護套電纜不得在日光下長期暴露。
  14. Commercial building telecommunications cabling standard - part 1 : general requirements - addendum 1 - minimum 4 - pair utp and 4 - pair sctp patch cable bend radius

    商用建築電信電纜敷設標準.第1部分:一般要求.補充件1 . 4對utp和4對sctp插塞式電纜的最小彎曲半徑
  15. Yff cable series want a temperature between - 20 and 60 ; allowed long - period working temperature 70. bending radius of the cable on less than 10 times of short axis diameter

    Yff電纜系列的使用環境溫度為- 20至60 ；允許長期工作溫度為70 ；電纜彎曲半徑不小於電纜短軸尺寸的10倍。
  16. Cable bending radius

    電纜彎曲半徑
  17. The bending radius should not less than 15 times of cable diameter

    電纜彎曲半徑：不小於電纜外徑的15倍。
  18. The bending radius should not be less than 25 times of the cable diameter

    電纜彎曲半徑：不小於電纜外徑的25倍。
  19. Permissive bending radius of cable should be no less than 20 times of external diameter of cable

    3電纜的允許彎曲半徑不小於電纜外徑的20倍。
  20. During installation the min ambient temperature shall be above 0 and the bending radius of cable shall not less than 6 times of its external diameter

    電纜的敷設溫度不低於0 ，推薦的允許彎曲半徑為不小於電纜外徑的6倍。
分享友人
分享到 Line

分享到臉書