靜態扭曲 的英文怎麼說

中文拼音 [jìngtàiniǔqū]
靜態扭曲 英文
static skew
  • 靜 : Ⅰ形容詞1. （安定不動; 平靜） still; calm; motionless 2. （沒有聲響; 清靜） silent; quiet Ⅱ名詞（姓氏） a surname
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 扭 : 動詞1 （掉轉; 轉動） turn round 2 （擰; 旋轉） twist; wrench 3 （擰傷） sprain; wrench 4 （走路時...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 靜態 : [物理學] static state; quiescent condition; steady state; statics; dead level; akinesis; akynesis...
  1. Static bend and torsion testing of intramedullary rods

    髓內用桿的靜態彎曲及扭轉試驗
  2. In this dissertation, in allusion to the limit that the domestic analysis and studies of the body structure only concentrate on the static bend, torsion and some extreme conditions in nowadays and the studies on transient analysis of the whole vehicle that contains the suspension model, tire model and the road model are few, the applications of the fem on the analysis of the car body structure are studied. and in this dissertation the method of building connecting means models, the dynamic response of the body, the fatigue analysis of the body and the reforming measures of the body are deeply discusses

    本論文針對目前國內車身結構分析的研究只限於對車身或車架結構在靜態扭轉、彎曲載荷以及幾種極限工況載荷作用等幾種情況的研究，對含有懸架、輪胎以及路面模型的整車瞬態響應分析的研究較少的實際情況，對有限元方法在汽車結構分析中的應用作了些研究工作，尤其是在車身連接件處理、車身動態響應、車身疲勞強度分析、車身結構改進方案等方面進行了較深入的探索。
  3. The static measurement includes weight, center of gravity, static lead lag, bending stiffness and torsion stiffness

    靜態測量包括重量，重心，靜前沿滯后，彎曲鋼度，和扭區鋼度。
  4. Through this method, we can analysis the stationary character of the liquid crystal with any twist angle, cell gap, effective optical anisotropy and angle between front director and polarizer

    參數空間法可用來分析具有任意扭曲角、盒厚度、固有雙折射率和偏振片角的液晶顯示器的靜態光學性質。
  5. 3 、 based on the model, a quasi - static meshing simulation is carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs. the different meshing position are presented, and the rationality of the model is be verified

    3 、基於所建有限元分析模型，在一個嚙合周期內，對齒輪副進行準靜態嚙合模擬分析，給出了準靜態嚙合時齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩和轉速隨嚙合位置變化的規律，驗證了所建模型的正確性。
  6. 4 、 on the basis of analyse of a quasi - static meshing simulation in a meshing period, a dynamic meshing simulation in the case of definite torque and rotary speed are carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs the different meshing position are presented

    4 、在對螺旋錐齒輪準靜態嚙合進行模擬分析的基礎上，進行了螺旋錐齒輪動態瞬態嚙合模擬分析，重點分析帶載啟動時出現的沖擊現象，得出了齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩、轉速和加速度隨嚙合位置變化的規律。
分享友人
分享到 Line

分享到臉書