靜態校準 的英文怎麼說

中文拼音 [jìngtàijiàozhǔn]
靜態校準 英文
static calibration
  • 靜 : Ⅰ形容詞1. （安定不動; 平靜） still; calm; motionless 2. （沒有聲響; 清靜） silent; quiet Ⅱ名詞（姓氏） a surname
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 校 : 校名詞1. （學校） school 2. （校官） field officer3. （姓氏） a surname
  • 準 : Ⅰ名詞1 （標準） standard; guideline; criterion; norm 2 （目標） aim; target Ⅱ動詞1 （依據; 依照）...
  • 靜態 : [物理學] static state; quiescent condition; steady state; statics; dead level; akinesis; akynesis...
  1. Basing on the analysis about the reason that how the superabundant torque appears, direct torque control strategy is used to realize the servo control of two asynchronous motors and load system ' s simulation. the measure method of superabundant torque of the system, the valid method of static state torque and the benchmark of dynamic torque are given by testifying the system ' s speediness through experiments

    在具體分析加載系統中多餘力產生原因的基礎上，採用直接轉矩控制策略，實現了兩臺異步電動機伺服控制和加載系統的負載模擬實驗，通過實驗驗證了系統的快速性；給出了系統多餘轉動慣量的測量、靜態轉矩的校驗和動態轉矩基準的實驗的基本方案。
  2. Standard practice for static calibration of electronic transducer - based pressure measurement systems for geotechnical purposes

    土工用電子傳感器型壓力測量系統靜態校準標準規程
  3. The principle and the mechanical structure of the air - gap inductance - type transducer are analyzed in this article, and the static parameters are calibrated. dynamic calibration is applied to air - gap inductance - type transducer which is not good in dynamic capability, to obtain the dynamic parameters of the transducer and its measuring circuit. based on the result of the dynamic calibration, the transducer and its serving circuit are modeled so that the method of how to improve the dynamic performance can be found

    本文對現有氣隙式電感傳感器在原理和機械結構上作了深入的分析，對其參數進行了靜態標定；並且針對常規電感傳感器動態響應低，不宜用於快速動態測量的缺點，引入測試系統動力學的思想，設計了一套動態校準系統，對現有傳感器進行多次動態校準，根據動態校準的實驗結果對現有傳感器建立數學模型，得到現有傳感器的動態特性；在此基礎上，根據磨床工件在線檢測的要求，設計一個硬體補償系統來提高整個測試系統的動態特性。
  4. Standard practice for calibration of the james static coefficient of friction machine

    摩擦機的james靜態系數校正的標準操作規程
  5. Metallic materials - verification of static uniaxial testing machines - tension compression testing machines - verification and calibration of the force - measuring system

    金屬材料.靜態單軸向試驗機的鑒定.拉伸和壓縮試驗機.測力系統的鑒定和校準
  6. The strain - gauge balance must be calibrated before it ’ s using in the wind tunnel tests, and the precision and accuracy of the balance will be affected by the characters of the calibration system

    而應變天平在用於風洞試驗前，必須進行靜態校準，天平校準系統的性能指標將直接影響天平校準系數的準確性。
分享友人
分享到 Line

分享到臉書