非反相放大器 的英文怎麼說
中文拼音 [fēifǎnxiāngfàngdàqì]
非反相放大器
英文
non-inverting amplifier- 非 : Ⅰ名詞1 （錯誤） mistake; wrong; errors 2 （指非洲） short for africa 3 （姓氏） a surname Ⅱ動詞1 ...
- 反 : Ⅰ名詞1 （方向相背） reverse side 2 （造反） rebellion 3 （指反革命、反動派） counterrevolutionari...
- 相 : 相Ⅰ名詞1 （相貌; 外貌） looks; appearance 2 （坐、立等的姿態） bearing; posture 3 [物理學] （相位...
- 放 : releaseset freelet go
- 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
- 放大器 : amplifier; pantograph; lawnmower; enlarger; magnifier
- 放大 : amplify; magnify; boost; enlarge; blow up; gain; amplification; enhancement; multiplication; magn...
-
Non - inverting amplifier
非反相放大器Based on these foundations, we give a perfect scheme of the bbo opos : single pass amplification coefficient of the opg under different pump intensity is calculated ; collinear type - i and type - ii phase matching tuning curve pumped by the q switch nd : yag various harmonics as well as noncollinear type - i tuning curve are calculated in details ; the effect of the walkoff for the nonlinear effect coefficient and the group velocity matching are analyzed ; the acceptance angle in parametric process is calculated ; the numerical threshold of the bbo opo is calculated ; the process of the saturation and depletion of the pump beam are analyzed ; the relationship of the conversion efficiency and reflectance of output mirror are discussed ; various linewidth controlling methods are discussed ; the improvement of the beam quality applying the unstable cavity is discussed ; and the crystal bbo design is considered
在此基礎上，給出了一整套bbo - opo激光參數設計方案：計算了不同泵浦強度下的參量放大倍數；詳細計算了在nd : yag調q激光器各次諧波泵浦條件下的共線類和類相位匹配的調諧曲線，以及非共線類相位匹配調諧曲線；分析了走離角對非線性系數和群速匹配的影響；計算了參量過程的允許角；計算了bbo - opo的理論閾值條件；分析了飽和與泵浦光束的消耗過程；給出了轉換效率與超過泵浦閾值的倍數的關系；討論了轉換效率與輸出鏡反射率的關系；討論了線寬控制的各種方法；研究了利用非穩腔改善光束質量的方法；考慮了bbo晶體的設計。And the ways to optimize the circuit architecture, minimize the circuit nonidealities and improve the circuit performance are analyzed combined with the characteristics of the modulator architecture. based on it, the switched - capacitor integrator, class a amplifier, nonoverlap clock, voltage reference, comparator, feedback dac have been designed. in the end, the layout design is shown
調制器採用全差分開關電容電路實現，並根據系統結構特點就如何優化電路結構、克服電路中存在的非理想特性、提高電路性能作了具體分析，在此基礎上完成了開關電容積分器（開關、電容、運算放大器） 、參考電壓源、比較器、兩相非交疊時鐘、反饋dac等模塊的電路結構和參數設計。
分享友人