非球面形 的英文怎麼說

中文拼音 [fēiqiúmiànxíng]
非球面形 英文
aspherical figure
  • 非 : Ⅰ名詞1 （錯誤） mistake; wrong; errors 2 （指非洲） short for africa 3 （姓氏） a surname Ⅱ動詞1 ...
  • 球 : 名詞1 （以半圓的直徑為軸 使半圓旋轉一周而成的立體; 由中心到表面各點距離都相等的立體） sphere; glo...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 球面 : spherical surface; sphere球面艙壁 spherical bulkhead; 球面車床 spherical turning lathe; 球面反射...
  1. In this paper, we brought forward an innovative idea : according to the characteristics of easy deformation of ultra - thin mirror, we employ a sphere mirror, which is easier to fabricate and test, to replace the aspherical mirror, then the sphere mirror is deformed into an aspherical one by active optics technology. on this purpose, we need to study the mechanism and method of shaping a spherical mirror into an aspherical one

    由於非球面鏡的加工和檢測都比較困難，因此本文提出了一個大膽的設想:利用超薄鏡易於變形的特點，以加工和檢測難度遠低於非球面的球面來代替非球面，運用鏡面的主動控制技術將球面反射鏡變形成所需精度的非球面反射鏡。
  2. The mathematic model of the ultra - thin spherical mirror is to be treated as elastic thin shell. then the predigested model, i. e., bended beam, used in qualitative analysis was proposed, and its deflection and stress formulas under the freely supported condition were set up. based on an off - axis aspherical primary mirror, the relationship of aspherical surface error ( rms ) in tangential plane with bended beam ’ s radius r, position s of concentrated load p and geometry length l of arc was analyzed

    根據這一設想，本文建立了超薄鏡的數學模型?薄殼，並提出了強制力作用下超薄鏡的簡化模型?曲梁，推導了曲梁在簡支情況下受力變形的撓度公式，並結合一個實例，計算出曲梁變形后與所需非球面的面形殘差（ rms ）在子午方向與曲梁弧長l 、曲梁半徑r及集中力位置s的關系及滿足面形精度的r和s范圍，分析了弧矢方向的rms ，得出了同時滿足子午和弧矢方向面形要求的l 、 r和p 。
  3. Because of the demand of aspherical lenses, itrc combines optical, mechanical and electrical technology to develop an aspherics polishing system using negative - shape polishing method

    在非球面光學鏡片需求增加的今日，儀科中心集成光、機、電技術，發展出應用負形拋光法之非球面拋光系統。
  4. When the machining tools is perfected, it can process all of quadric curves and high degree curves with high surface form precision. at the same time, the its structure is very simple processing size range is large and its efficiency is high, so it will greatly reduce the cost of processing of aspheric parts

    該機床完善後，可加工所有二次曲線和高次曲線，並能保證較好的零件面形精度，該機床結構簡單，加工尺寸范圍大，加工效率高，將會大大降低非球面加工的成本。
  5. An optimizing arithmetic for calculating the best - fit sphere is also proposed, the result shows better accuracy is reached comparing to " three points method ", from 107. 8umrms to 25. 66umrms. during interferometric optics test with null lens, " nonlinear errors " of the testing coordinates will be introduced. a method based on ray - tracing, nonlinear fitting and coordinate transferring is proposed to eliminate these errors

    在ccos控制模型及理論計算方面，提出了一種適用於高次離軸非球面最接近球面計算的優化演算法，經計算，某矩形離軸非球面最接近球面半徑的求解精度較傳統的「三點法」有了較大的提高，理論加工余量由原來的107 . 8umrms降低到25 . 66umrms ；提出一種基於磨頭與工件的相對位移量的控制模型，並且開發了阻尼卷積迭代演算法，引入「虛擬加工」的概念進行迭代求解和參數評價。
  6. Besides, the test and test result of some key components, eg. pev and the infrared laser system, are introduced. finally described is the special measurement, with infrared phase - shifting twyman interferometer, of a rough reflective surface and an aspherical surface

    文中還介紹了對pev 、紅外激光系統等關鍵部件的測試與調試結果，介紹了利用紅外干涉儀進行的特殊測試如拋光前的光學粗糙表面及某些非球面面形等。
  7. " misalignment error ", which is caused by misalignment during null test adjustment, together with fabrication errors is shown in test results, and it is important to separate these two errors so that the test results can be used in ccos process. asic software is developed for eliminating nonlinear error and separating misalignment error, and a high accuracy, suitable format data file is generated by asic for further analysis for ccos process

    在非球面測量技術方面，主要針對零位補償檢驗過程中測量坐標的「非線性誤差」的形成原因及其補償演算法由光學調整量引起的測量誤差以及調整量誤差的擬和方法等問題進行了討論，並編制了相應的干涉檢驗數據處理軟體asic ，干涉檢驗結果經分析、處理后能夠滿足ccos的技術要求並指導加工。
  8. Progress on testing large aspheric mirror with annular subaperture method

    以環形子孔徑法檢測大口徑非球面主鏡的研究進展
  9. By many experiments and analysis, we could prove that our aspheric surface measuring instrument in miniature reaches the request of designment. it could meet the measuring requirement of laboratory and optical shop for grinding surface, its practical testing precision is 1 - 2um. meanwhile it is suitable for final testing of optical element with reasonable accuracy

    通過多次實驗以及數據處理、分析，證明自行設計、裝調的非球面輪廓儀以及測量軟體達到了設計的精度要求，可滿足實驗室，光學加工車間對小型非球面光學元件精磨階段面形的檢測要求，其實用精度為1 - 2um 。
  10. But the domestic ultra - precision machining of aspheric surface, especially the large - scale aspheric surface, is just the same as blank, which has no systemic research

    而國內非球面特別是大型非球面的超精密加工還是空白，還沒有形成系統的研究。
  11. In this paper, on basis of the current machining state, a testing principle on aspheric surface is put forward to, the principle is a kind of touching method by testing the meridian of aspheric surface and comparing it with the theoretical curve, so surface figure error is got. according to this principle, mechanical structure is designed and electric - control system is researched

    本文首先基於現階段非球面的加工狀況，提出了用接觸式檢測非球面的子午面面形曲線並與理論曲線相比較，從而得到非球面面形誤差的檢測原理，並根據該原理進行了機械結構的總體設計和電控系統的研究。
  12. The surface testing of aspheric and optical part is especially difficult, which is big scale and high precision

    尤其是大型高精度的非球面光學零件，面形檢測難度更大。
  13. The precision of polishing of optics depends on the precision of grind. the general procedure of processing aspheric optics is coarse grinding, fine grinding, polishing and measuring

    光學元件的拋光精度取決于精磨精度，非球面光學元件的加工工序簡略的可分為粗磨成形、精磨成形、拋光、檢測。
  14. In this article some basic problems in the ccos are studied on the aspheric optical compound machine tool ( aocmt ). the main contents and innovations include : [ 1 ]. the deterministic model is built for grinding and polishing processes

    本文以光學非球面復合加工機床（ asphericopticalcompoundmachiningtool ， aocmt ）為對象，對計算機控制光學表面成形技術中的一些基本問題進行了研究。
  15. The projection optics with aspherical mirror of sub - nanometer accuracy are required to get a resolution of less than 0. 1 m m and wide exposure area simultaneously. the precision of polishing and testing for such ashperical surface is fairly high and it has not been achieved yet in our current state

    Euvl微縮投影物鏡為了同時實現大的曝光視場和0 . 1 m以下的成像解析度，微縮投影光學系統需採用面形精度達亞納米量級的非球面，但我們現階段的光學加工和檢測技術距此要求尚有一定的差距。
  16. The data formats of optical design software ( code v ) and optical cnc machines are investigated. based on the function of optical design software that can output documents with file type of txt, we developed the software in visual c + + used to control optical manufacture process. the software can find parameters of curve surfaces from the documents, handle the data stream of optical design software, the technological parameters of optical manufacture machines and surface error data of talysurf, and simulate the manufacture process

    研究光學設計軟體（ codev ）和光學cnc製造設備的數據格式，利用光學設計軟體的文檔輸出功能，採用vc + +編制一個能從上述文件中自動發現曲面方程的介面，處理光學軟體數據流、光學設備工藝參數以及輪廓儀的面形檢測數據，模擬加工過程，生成用於光學加工的控制代碼實現非球面的銑磨和拋光，實現光學cad cam一體化製造。
  17. This research is aim at putting forwarding laser wavelength scanning interference testing method. processing and analyzing instantly - read interference pattern corresponding with continuous varying wavelength, the method overcomes the following disadvantage. for example, the longer referenced and measuring optical circuit in big - scale high - accuracy asphere testing, and the sensitive interferential system to the disturb, such as the oscillation of worklable, dithering of air, and so on

    研究的目的主要是針對大型高精度非球面面形檢測中干涉儀的參考光路和測量光路較長，干涉系統對工作臺振動和空氣抖動等外界干擾因素的影響敏感，干涉圖不穩定等問題，提出了激光波長掃描干涉測試方法，該方法通過對瞬間讀取的、與連續變化波長對應的干涉圖的處理和分析，克服了上述缺點，為大型高精度非球面的檢測提供了一種適用的方法。
  18. The paper studies mainly a new kind of measure method of aspheric surface - laser wavelength - scanning interference testing. this research is aimed at putting forwarding laser wavelength scanning interference testing method. processing and analyzing instantly - read interference pattern corresponding with continuous varying wavelength, the method overcomes the following disadvantage : the longer referenced and measuring optical circuit in big - scale high - accuracy asphere testing and the sensitive interferential system to the disturb, such as the oscillation of worktable, dithering of air, and so on

    研究的主要目的是針對在大型高精度非球面面形檢測中干涉儀的參考光路和測量光路較長，干涉系統對工作臺振動和空氣抖動等外界干擾因素的影響敏感，干涉圖不穩定等問題，提出了激光波長掃描干涉測試方法，該方法通過對瞬間讀取的、與連續變化波長對應的干涉圖的處理和分析，克服了上述缺點，為大型高精度非球面的檢測提供了一種適用的方法。
  19. Optics and optical instruments - preparation of drawings for optical elements and systems - aspheric surfaces

    光學及光學儀器.光學元件和系統圖紙的制備.第12部分:非球面形表面
  20. Optics and optical instruments. preparation of drawings for optical elements and systems. part 12 : aspheric surfaces

    光學和光學儀器.光學元件和系統圖紙的制備.第12部分:非球面形表面
分享友人
分享到 Line

分享到臉書