韌化劑 的英文怎麼說

中文拼音 [rènhuàjì]
韌化劑 英文
toughening agent
  • 韌 : 形容詞（不易折斷; 柔軟而結實） pliable but strong; tenacious; tough
  • 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
  1. The methods - three dimension fabric - enforced laminates, and sparse fabric - enforced laminates, layer - enforced laminates ? to enhance the interlaminar toughness of fabric - reinforced laminates were discussed in this paper. the stitching method to enhance interlaminar toughness of stitched - laminates was mainly discussed in this paper based on our research and experiment. the middle - alkali glass fabric used as enforced - material with thickness of 0. 2mm, 3 section 600 deniner kevlar yarn is used as stitching thread in this research, which improved lock stitching way and different kinds of stitching mode were adopted

    以提高層合板復合材料的層間斷裂韌性（能量釋放率）為目標，採用中堿玻璃布為增強材料，對疊層后的玻璃布，採用凱芙拉縫合線、改進的鎖型縫合方法、不同的縫合工藝進行了縫合；基體採用的是不飽和樹脂，固化劑為過氧化甲乙酮，促進劑為環烷酸鈷液；在室溫下採用真空輔助rtm （ resigntransfermolding ）成型固化方法，製作了不同縫合工藝的玻璃布增強復合材料層合板。
  2. Filling flexibilizer, such as epoxy terminal block, polyurethane ether structure, thiokol and liquid ctbn to the system of expoxy - mannich amide, through the test on shear strength, bounding elasticity modulus and break strength of cured products, the different fuction could be found using different flexibilizers

    摘要在環氧酚醛胺體系中使用端環氧基聚氨酯醚、聚硫橡膠、液體丁腈橡膠等活性增韌劑，通過對固化物剪切強度、彎曲彈性模量及斷裂強度的測試對比，可以看出不同增韌劑效果不同。
  3. They can also be used for fiber sizing, textile finishing, the reinforcing agent for cement and ceramics, and the preparation of various kinds of latex paints, and all kinds of special adhesion agents. the products of vinyl acetate - acrylic ester copolymer emulsion, which have overcome some defect of homopolymerized products, are newly developed. the modified emulsion has stronger water resistance, better flexibility, and lower glass state temperature

    醋-丙共聚系列乳液產品是針對均聚產品的某些缺陷而發展起來的新膠種，它通過醋酸乙烯與丙烯酸脂類共聚改性，提高膠粘劑的耐水性和柔韌性，降低共聚物的玻璃化溫度，使產品對一些均聚乳液難以粘接的材料具有良好的粘接性能，主要產品有：寶麗板膠鋁箔紙膠塑板膠等。
  4. Self - prepared paper varnish with excellent comprehensive properties, adhesion is well, glossiness is > 110 % and resistance to acetone is > 200 times. self - prepared uv printing ink adhesion is well, glossiness is > 80 %, tenderness is 1mm and resistance to acetone is > 200 times, and through aging testing, the coating film did n ' t become brittle

    研製的紅、黃、藍三種顏色的uv油墨，經性能測試表明：光澤度80 、附著力合格、耐溶劑性200次、油墨性能良好，柔韌性1mm ，長時間老化實驗后塗層沒有出現發脆的現象，改善了現存油墨的脆性問題，油墨性能良好。
  5. Through the research on the crystallite of the composites modified with silicone coupling agent and pp - g - mah, research showed that the size of the crystallite and oriented crystallization had obviously influence on the mechanical performances. the sem results showed that nano - sio2 was dispersed well in pp, which promoted the matrix undergo shear yielding rather than brittle fracture

    通過對硅烷偶聯劑?馬來酸酐接枝聚丙烯共聚物作為界面改性劑改性pp微晶的研究，表明微晶尺寸變化與復合材料的力學性能有關；在界面附近形成擇優取向的結晶層，促使基體發生屈服變形，提高了復合材料的韌性。
  6. The boundary of ferrite has been clarified and fined by adding re into crsomo. the intergranular corrosion induced by solution chromium decreasing can be restrained for nb, v, ti combing carbon in the steel. the wear resistance of stainless steel can be increased for the precipitation of microalloyed carbides

    其中，稀土能夠凈化鐵索體晶界，並起到變質劑的作用，細化鐵素體晶粒，改善不銹鋼的韌性；鈮、釩、鈦能夠與鋼中的碳結合，減少固溶鉻的損失，從而避免晶間腐蝕，同時細小微合金碳化物的沉澱析出可提高不銹鋼的耐磨性。
  7. In this paper, the properties of fluid - modified epoxy resin containing different thinners, ethylamine anti plasticizer were tested and the effect of fluid - modified epoxy resin in repairing concrete crack through embedded pipe was compared with that of conventional grouting

    測試了不同稀釋劑、固化劑及增韌劑綜合改性的環氧樹脂多組配方灌漿液的性能，對通過預埋玻璃管模擬灌漿修補混凝土裂縫的效果與通過縫面灌漿修補混凝土裂縫的效果進行了比較。
  8. Cbn120 bright black mono - crystal, regular shape, high toughness and good thermal stability. mainly used for metal, vitrified bond and electroplated tools, wheels. the tools have longer service life

    Cbn120亮黑色立方氮化硼單晶，等積形單晶體，晶體較完整，具有較高韌性和熱穩定性。主要用於電鍍、金屬、陶瓷結合劑磨具、砂輪、工具，使製品具有更長的使用壽命，適合磨削黑色金屬材料及合金。
  9. The result showed that after adding grain refiner, the hardness of magnesium alloys changed little while the impact toughness increased

    結果表明，添加細化劑后，鎂合金的硬度變化不大，而沖擊韌性提高。
  10. Preparation of polymer composites is one of the important methods to realize high performance of polymer materials. in this paper, a newly developed ethylene - octene copolymer ( eoc ), catalyzed by metallocene catalysts, was used as an impact modifier for pp instead of traditional modifier ( epdm ). the relationship between the structure and properties of polypropylene composites toughened and reinforced by eoc and cacos respectively or together was studied systematically

    聚合物復合材料的制備是實現高性能聚合物材料的重要途徑之一，本論文採用茂金屬催化劑合成的新型聚烯烴彈性體乙烯-辛烯共聚物（ eoc ）代替傳統的三元乙丙橡膠，對eoc和caco _ 3兩種增韌劑分別和協同增韌增強聚丙烯復合材料體系的形態結構與性能的關系進行了系統的研究，圍繞高性能、應用探索和理論研究三個方面作了較為深入的探索和分析，獲取了很多有價值的信息，為高性能聚丙烯復合材料的開發和應用作了理論鋪墊，主要結果如下： 1
  11. The addition of y - zro2 improves the fracture toughness of pcd and the grinding ratio also increases with the y2o3 content increasing. the optimum comprehensive properties of pcd can be achieved as the y - zro2 powders contain 2mol % y2o3. aluminum addition in si3n4 or si3n4 bond pcbn can prevent y - zro2 powders from forming the nontransformable tetragonal phase

    在si _ 3n _ 4及si _ 3n _ 4中介結合的pcbn中加入適量的al作為燒結助劑，可以避免不可相變的t相zro _ 2形成，使應力誘導相變增韌高溫高壓燒結的氮化硅系陶瓷成為可能。
  12. Cbn230 yellow mono - crystal, transparent, regular shape, high toughness and hardness. suitable for electroplated ， vitrified and metal bond tools, wheels etc. the tools have long service life

    Cbn230金黃色立方氮化硼單晶，等積形透明晶體，高韌性，高強度。適用於電鍍、陶瓷、金屬結合劑體系磨具、砂輪、工具製造。其製品使用壽命長。
  13. When change the component of adhesive its shear strength increased from 39. 3 mpa to 53. 5 mpa at room temperature and it have long - term usage at 180 with 25 mpa and can be served at 230 in short period. the addition of liquid rubber resulted in a 300 % increase in the peeling strength. the addition of polymer ether imide led to a 260 % increase in the peeling strength, a 15 % increase in shear strength and a 10 increase in tg ( tg = 195. 54 )

    研究結果表明： bmi dds e ? 51 tde ? 85組成的膠粘劑體系的室溫剪切強度為39 . 3mpa ，當改變環氧樹脂的含量時，剪切強度提高到53 . 5mpa ；用無規羧基液體丁腈橡膠改性環氧樹脂膠粘劑時室溫剝離強度提高3 . 0倍；用聚醚酰亞胺改性環氧樹脂膠粘劑，室溫剪切強度最高可達45 . 2mpa ，剝離強度提高2 . 6倍，玻璃化轉變溫度tg = 195 . 54 ，比未增韌體系提高10以上；碳纖維耐磨材料與同步器圓錐環的粘接實驗結果表明，膠粘劑的使用工藝性能良好，滿足室溫剪切強度30mpa和180剪切強度12 . 5mpa的技術要求。
  14. The curing conditions were studied and the result indicated that the product showed a good storage, decreased the curing temperature, improved adhesion and brittleness, with an excellent film performance. expecially the adadhesion, flexibility and chemicol resistance

    結果表明，合成的交聯劑貯存性能良好，醚化三聚氰胺樹酯作為交聯利加入到丙烯酸環氧樹酯中，可以明顯降低固化溫度且改善原有塗膜的脆性，成膜性能好，尤其是具有優良的附著力、柔韌性和耐化學品性。
  15. Toluene is a colorless liquid used as a solvent, formaldehyde helps harden nails and dibutyl phthalate is a plasticizer that makes nail polish flexible

    甲苯是一種無色液體，用做溶媒；甲醛幫助硬化指甲；而鄰苯二甲酸二丁酯是一種增塑劑，增強指甲油的柔韌性。
  16. This paper analyses the problem of concrete cracking and leakage, and set up the model of the middle or low - strength steel slag anti - cracking and impermeable concrete ( acic ) on the base of the analysis. the four principles of water permeable resistance character, volume stability character, toughness and anti - chemical corroded character have been put forward for raw materials selection and durability design of acic, acic is designed by the theory of composite material and the theory of fiber - reinforced, and two series of acic, such as fly ash series and steel slag series, have been manufactured by means of mineral admixture, hybrid fiber and chemical admixture. hydrating heat, macro - mechanics quality, durability and microstructure of the acic have been researched

    本文對中低標號大體積混凝土滲透開裂問題進行了研究，從混凝土自身結構形成與經濟角度指出大摻量粉煤灰與膨脹劑復合配製大體積混凝土的問題所在，提出採用鋼渣微細礦粉配製中低標號防滲抗裂混凝土的思路，運用復合材料理論設計中低標號防滲抗裂混凝土，提出了低水化熱、抗滲性能、體積穩定性、韌性和抗沖磨性能是中低標號防滲抗裂混凝土材料選擇和耐久性設計的主要原則，採用鋼渣微細粉復合混雜纖維、化學外加劑的技術路線，配製了適合於深水等特殊環境中的大體積中低標號鋼渣系列防滲抗裂混凝土，對其進行水化特性、宏觀物理力學性能、耐久性和微觀結構研究。
  17. Leather based varnish was prepared with self - prepared prepolymer. the capability testing suggested that glossiness is > 110 %, resistance to cracking is > 30000 times, resistance to acetone is > 200 times and adhesion is well. in the study of uv printing ink suggested that when the pea / bpua ( wt ) is 3 / 1 - 4 / 1, the coating film had good capability : adhesion is well, glossiness is > 110 % and tenderness is 1mm

    在研製紙印品uv上光油和油墨的應用實驗中，討論了顏料與引發劑的配伍性、顏料的用量對光固化速度的影響，並對pea和bpua兩種樹脂的共混比例進行了研究，結果顯示pea bpua = 3 1 - 4 1時，固化后性能測試顯示：附著力合格、光澤度100 ，柔韌性1mm ，綜合性能良好。
  18. It is the especial congregate structure of polymer matrix that is necessary for the forming of three - dimensional interpenetrate network between the polymer and copper. the mma unites lead to the advantage of improving fiexibity of the film, destroying the formal arrangement of macromolecule chain in polymer and decreasing the degree of crystallization. the ita unites help the solvolyzed copper ion transfer in the film and benefite the forming and establishment of the networks of polymer matrix

    聚合物基體特殊的聚集態結構是互穿立體網路形成的必要條件，皿m的加入有利於破壞丙烯睹大分子鏈的規整性，使結晶度降低，提高聚合物的柔韌性，含親水基團的單體（ ita 、 as ）存在有利於降低離子遷移的界面能，提供溶劑化銅離子遷移的途徑以及聚合物基體網路結構的形成和穩定。
  19. Cbn115 black mono - crystal, regular shape, medium toughness. mainly used for resin, vitrified bond and electroplated tools and wheels

    Cbn115黑色立方氮化硼單晶，中等韌性，主要用於樹脂、陶瓷、電鍍結合劑磨具、砂輪、工具製造。
  20. Ep epoxy powder coating are thermosetting powder coating based on epoxy resin, with modified of diversiform curing agent, and are characterized of anti corrosive, excellent impact toughness, and used in pipeline corrosion protection, family fitting etc

    Ep粉末塗料是一種以環氧樹脂與多種固化劑改性而成的熱固性粉末塗料，具有較好的耐化學腐蝕性，極佳的沖擊韌性，廣泛應用於重防腐的管道，家庭用具等領域。
分享友人
分享到 Line

分享到臉書