頻率測試臺 的英文怎麼說

中文拼音 [bīnlǜcèshìtái]
頻率測試臺 英文
frequency measuring station
  • 頻 : Ⅰ形容詞（次數多） frequent Ⅱ副詞（屢次） frequently; repeatedly Ⅲ名詞1 [物理學] （物體每秒鐘振動...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 臺 : 臺名詞（指臺州） short for taizhou （in zhejiang province）
  • 頻率 : frequency; rate
  • 測試 : test; testing; checkout; measurement
  1. First, the theory of fretting wear and studies on fretting fatigue were introduced and the parametric method was used in the process of creating the model of dovetail joints in ug software. the elastic contact problem is analyzed in finite element method ( fem ) and is used to the parameters " distribution and contact stress of the joint are obtained on the base of ansys code. with the effect factor of load frequency, the prediction method of fretting fatigue life of dovetail joint under low and high / low cycle complex load is proposed

    本文介紹了微動損傷的機理和微動疲勞壽命的研究方法；利用ug軟體對燕尾榫聯接結構創建了參數化實體模型；基於ansys軟體平臺求解彈性接觸問題，獲得了榫聯接結構接觸應力及接觸狀態量的分佈；在已有微動疲勞壽命預測模型的基礎上，引入載荷頻率影響因子，對低周、高低周復合載荷作用下的燕尾榫聯接結構進行了微動疲勞壽命的預測，與試驗結果對比表明採用本文提出的方法預測榫聯接結構的微動疲勞壽命是有效的。
  2. In this thesis, firstly, we put forward a new algorithm of the synchronization of carrier reference phase, that is to use the curve synthesizing with the general digital carrier phase looper to have an estimation on carrier frequency within 10 ms so as to meet the need of meteor burst communication. we have done some simulations to get the performance of carrier frequency estimation using two modulation modes ( 16qam and 4 - qpsk ), and had some test on the carrier phase looper in conditions when using different baud rate transmission and when the baud tuning have windage

    我們對兩種正交調制方式（ 16qam和4 - qpsk ）進行了模擬工作並給出了模擬結果，同時討論了碼元同步定時誤差對鎖相環路工作的影響並根據流星通信中使用變速率傳輸時鎖相環路的載波同步性能進行了測試；然後在基於軟體無線電思想的數字處理平臺（該數字處理平臺實現了中頻數字化）上用dsp軟體完成了載波的相位跟蹤。
  3. On the part of the design of nine - component thrust vector stand, an automatic hydraulic pressure original position calibration system, a scheme of original position calibration, and the great rigidity universal flexible combinatorial underprop are designed. by using the scheme of “ universal flexible combinatorial underprop plus software digital filter ”, the inherent frequency of test stand is improved, and the problem of test stand libration is solved. then, the resolving method of the disturbance between underprops of the moveable frame is proposed, and the disturbance revise equation is deduced

    在推力矢量試車臺設計方面，設計了自動液壓原位校準系統、原位校準方案以及大剛度萬向柔性組合支撐;採用「萬向柔性組合支撐+軟體數字濾波」的方案，提高了試車臺動架的固有頻率，解決了試車臺動架的振動問題;提出了動架約束互擾問題的解決方法，推導了互擾修正方程;研究了九分力推力矢量測量誤差分析方法，並計算了推力矢量測量精度。
  4. Under windows nt and labview development environment, using the linear fit module, exponential fit module > general polynomial fit module of labview to design a method for fitting the experiment data, the results of curve fitting indicate that the purpose of general polynomial fitting is better than the rest. separating the equivalent input impedance of magnetostrictive transducers without stimulate current from input impedance of it with stimulate loop based on the results of curve fitting, and determining the syntony frequency and electric simulation network parameters of magnetostrictive transducers by this input impedance. finally, with labview network functions, realizing magnetostrictive transducer electric simulation system based on web server and discussing a scheme for this system network by datasocket. the method of this paper can more accurately determine the syntony frequency and electric simulation network parameters of magnetostrictive transducers than the testing method of syntony & anti - syntony. at the same time, discussing virtual instrument measurement system and how to realize magnetostrictive transducer electric simulation network system by labview network functions of network virtual instrument measurement development environment

    在windowsnt系統環境和labview虛擬儀器技術開發平臺下，首次利用labview中的直線擬合模塊、指數擬合模塊以及多項式擬合模塊，設計了一種對實驗所得數據進行曲線擬合的方法，對三種擬合方法進行了比較，曲線擬合結果表明，多項式擬合方法相對于其它兩種擬合方法效果更好；根據曲線擬合的結果可從帶激勵線圈的磁致伸縮換能器的輸入阻抗中分離出磁致伸縮換能器鐵芯在無激勵電流時機械振動形成的等效輸入阻抗，並由此輸入阻抗確定了磁致伸縮換能器的諧振頻率及其電氣模擬網路參數；最後通過labview提供的網路功能，實現了基於web服務器的磁致伸縮換能器電氣模擬虛擬儀器測試系統，並探討了通過datasocket技術實現該系統網路化的方案。
  5. In this dissertation, we studied the tcra1101plus total station position system, which introduced the principle and characters of the instrument ' s closed loop tracking system. also we explained the cause of prism ' s position error and brought forward mathematic model to correct, moreover, the good results has been drawn form the expenriments. the kinetic survey system have been realized, which the sampling rate attain more than 5hz and the position precision can be less than 2mm on condition that targeted - point moving slowly at the velocity below 2cm / s. having finished the survey system to examine whether the fine - tuning stewart platform in good status, we have finished mensurating the position reference of the fine - tuning stewart platform and the offset of the prism

    在此基礎上研製了多臺儀器在線控制高頻采樣動態跟蹤測量系統，采樣率大於5hz ，在跟蹤小於2cm / s低速運動目標時，測量精度好於2mm ；完成對饋源二次精調系統的檢測，包括對二次精調平臺位置基準的標定和觀測棱鏡偏心差的測定；設計不同動態測量實驗，對全站儀動態跟蹤的誤差來源和特點進行了分析；從實驗角度，對全站儀的測量時滯及其穩定性進行了測試分析，給出了定量的結果；比較了全站儀和計算機的內部時間系統，發現兩者存在較大差異。
  6. It is based on the platform of hardware of fpga, dsp, d / a to realize the concise and full - function digital variable bit rate test signal resource. this paper discuss the ways of full digital if and realize it, certainly the ways to realize the carrier frequency, sub - carrier frequency and variable bit rates with dds technology is also presented

    本課題是以fpga 、 dsp 、 d / a為硬體平臺，設計實現了結構簡明，功能完整的全數字可變速率測試信號源，討論並實現了中頻頻段如何實現全數字的方法以及用dds技術實現載波頻率，副載波頻率，碼速率的方法。
  7. Data processing software is designed for tbs - 2000 strain measuring system in the classical virtual instruments engineering workbench ; it is applied to process the data which are acquired in the way of dynamic stress analysis, statistic stress analysis and proper frequency analysis

    利用虛擬儀器的典型開發平臺labview針對tbs ? 2000應變測試系統開發了數據處理軟體；利用該數據處理軟體對測試所得的數據進行了動、靜應力分析和固有頻率分析。
  8. This master ’ s degree thesis firstly introduces and discusses the principle of ofdm and the merged blue print for digital terrestrial television broadcasting in china, then proposes a scheme for the test platform of narrowband ldpc decoding efficiency based on fpga. this scheme includes techniques such as time - domain synchronization using pn and power estimation using pilots

    本論文首先介紹並討論了數字電視傳輸標準tds - ofdm的實現原理，對其中的一些關鍵問題做了詳細的分析，在此基礎上提出了一種基於fpga的窄帶ldpc解碼-誤碼測試平臺設計方案，即利用時域pn頭同步及頻域導頻進行功率估計的fpga設計。
  9. This thesis probes into design of microcomputer system taking single chip microcomputer as central, anti - interference, security segregate and design of interface circuit etc. furthermore, the option to cycle of sampling various frequencies examine signals is also analyzed and it was utilized in the examine system. thus, the dependability and stability problem of the microcomputer examine system of hydraulic resistance testbed have been solved better, make this test a modern techniques and practibility is good

    本文在以單片機為核心的微機系統的設計、介面電路設計、抗干擾技術及安全隔離技術等方面進行了較深入的研究，分析了不同頻率檢測信號采樣周期的選擇，並在檢測系統中得到了應用，較好地解決了水阻試驗臺微機檢測系統的可靠性和穩定性問題，使得該試驗臺技術先進、實用性好。
  10. Through establishing three mathematics models including the movement equation of the mechanical and electrical transmission system, the control of the load and the sliding in stable status, direct - current - brake of ac motor, this paper ascertained the range of the frequency value of drive motor and the efficiency of transmission system, calculated the efficiency of load motor in stable status and the moment of load motor in braking. this paper completed the design of the mechanical part of inertia brake test platform and provides a tool for the measurement of the inertia brake parameters

    本文還通過建立慣性制動器試驗臺的包括機電傳動系統的運動方程、穩態運行時負載與轉差率控制、交流電動機直流制動在內的三個數學模型，確定驅動電機的頻率取值范圍和傳動系統的傳動效率，驗算慣性制動器穩態運行時負載電機軸功率和慣性制動器制動時負載電機軸力矩，完成慣性制動器試驗臺設計中的機械部分，為慣性制動器各參數的測量提供工具。
  11. The designed testing instrument has the functions of many instruments, such as frequency selective level meter, oscillator, frequency meter, millisecond meter and so on. all measuring and data processing are accomplished by the application software that is installed in a computer

    在功能上，裝置集電平振蕩器、高頻頻率計和選頻電平表等多臺儀器的功能於一體，且裝置的所有試驗操作、測量及數據處理由安裝于通用計算機上的應用軟體完成。
  12. This thesis presents a forward error correction ( fec ) algorithm and its circuit implementation, which is used in the wireless digital audio transmission system. also, an entire demo platform is built and error - correction ability of the system is tested based on this platform

    本文研究了一種應用於數字音頻無線傳輸系統中的前向糾錯（ fec ）演算法和相應的電路設計，搭建了一個硬體驗證平臺，並在驗證平臺上完成了電路的誤比特率測試。
  13. The developed system provides a test analysis platform for the study of the effects of the size parameters of the pec and the frequency and the amplitude of the external excitation on the electricity generating capacity of the pec

    該測試系統為研究壓電陶瓷尺寸參數、外界激勵的頻率和振幅對壓電陶瓷發電能力的影響提供了測試分析平臺。
  14. The main chip of the usb interface circuit is a cypress semiconductor ' s product, cy7c64613, which has intergrated usb sie ( serial interface engine ) and enhanced 8051. the oscilloscope module is realized according to the real time sampling principle. it has two signal chunnels and a dual 8 - bit dual a / d converter whose most sampling rate is 40msps, so two signal acquisition can occurs in the same time

    隨后介紹虛擬儀器測試平臺中各硬體模塊設計實現： usb介面的主晶元是cypress公司的cy7c64613 ，此晶元集成了usbsie和8051核；示波器模塊根據實時取樣原理實現，採用雙8位a / d轉換器，提供兩條信號通道，可以同時採集雙路信號，最高的采樣率為40mhz ；信號源模塊採用直接數字合成（ dds ）原理實現，它所能產生的信號頻率為10hz 5mhz ，最小頻率解析度為9 . 537hz 。
  15. The epmi can measure voltage, current, frequency, power, energy and other electrical parameters synchronously, and display the measured parameters on lcd. furthermore, the epmi can transmite the measured data to the surveillance room through rs485 bus interface. if there are many epmis, they can be formed as a controlling network and managed easily

    本測試儀可以同時對電壓、電流、頻率、功率和能量等電參數進行測量，參數顯示採用液晶顯示技術，並配有rs485通信介面，可以將測量的數據傳送到監控中心，多臺測試儀表還可以形成控制網路，便於管理。
  16. In order to carry out the acoustic and aerodynamics performances tests, seven resonators are designed and made, and a specialized engine intake silencer and exhaust silencers test bench was designed. the tests and analysis are performed as well. on the basis of the intake noise spectrum of sc7080a, a three - parallel - connected resonant silencer is designed, and that has efficiently controlled the acceleration noise of sc7080a

    在此基礎上設計並加工了兩類七個共振型進氣消聲器，研製了發動機進排氣消聲器性能測試實驗臺，開發了發動機進排氣消聲器聲學性能測試軟體，並在該實驗臺上測試了所設計的進氣消聲器靜態工況下的傳聲損失，從實驗的角度研究了共振腔的尺寸、形狀對其共振頻率的影響及其趨勢。
  17. The mode number and the frequencies range, which were considered during calculating the wind - induced responses of large cantilevered roof by using the method of frequency domain, were analysed and discussed, according to the results of wind tunnel tests of bahamas and guinea stadium grandstand cantilevered roofs, and the rules that rms displacement and rms internal force responses under strong wind force changing with participant modes number and frequencies range were obtained, and which could be explained from the point of wind pressure power spectrum densities of the measured points on surface of the roof

    摘要根據援巴哈馬體育場和援幾內亞體育場主看臺懸挑屋蓋風洞試驗數據結果，分析和探討了採用頻域分析法計算大跨度懸挑屋蓋風振響應時應考慮的結構模態數和頻率范圍，得到強風作用下懸挑屋蓋結構均方根位移與內力響應隨參與計算的模態數和頻率范圍的變化規律，並從屋蓋表面測點風壓譜密度的角度解釋了這種變化規律。
  18. We equip the following machines for the environmental testing and the reliability test : test box with high and low temperature, test box with high temperature, test box with invariableness temperature and humidity, salt - spray test box, vibrant and impactive test machine, tensile test machine, frequency tester and scanner, oscillograph, oven with invariableness temperature etc. pic the 3d machine

    環境試驗可靠性測試等方面配置有以下儀器設備：高低溫試驗箱高溫恆溫試驗箱恆定濕熱試驗箱鹽霧腐蝕箱振動沖擊試驗臺拉力試驗機諧振頻率f0快速測試儀揚聲器f0快速測試儀音頻掃頻信號發生器示波器電熱恆溫乾燥箱等。
  19. Usually in ofdm system, the time - domain synchronization in the platform is the symbol - frequency synchronization using pn - sequence preambles. its algorithm has been designed based on the requirement of platform, and validated by matlab simulation. then the verilog program has been designed based on this algorithm

    測試平臺中的時域同步是ofdm系統下基於pn序列的符號和頻率同步，其演算法是根據融合方案時域同步演算法，同時結合測試平臺系統要求設計的，演算法性能已經通過matlab模擬得以驗證。
分享友人
分享到 Line

分享到臉書