髖股的 的英文怎麼說

中文拼音 [kuāngǔde]
髖股的 英文
coxofemoral
  • 髖 : 名詞（髖部） hip
  • 股 : Ⅰ名詞1 （大腿） thigh; haunches 2 （機關、企業、團體中的組織單位） section of an office or enterp...
  • 的 : 4次方是 The fourth power of 2 is direction
  1. To meet the processing requirements before sintering, the pressed briquet was pre - calcined at 1150 to make it possess adequate processing strength at first and then was shaped through precise turning on the numerical control lathe according to the design diagram of the femoral head prostheses of partial hip joint

    為滿足燒結前坯體加工的要求，壓制后的坯體在1150預燒，使其具備一定的加工強度，然後按照半髖關節股骨頭假體的形狀尺寸設計圖在數控車床上進行精密車削成型。
  2. Management of ipsilateral acetabular fractures and posterior hip dislocation and femoral fractures

    股骨幹骨摺合並同側髖臼骨折與髖關節后脫位的治療體會
  3. At last, the surface of the alumina femoral head was grade - polished with sic micropowder and diamond grinding cream, the join part was trimmed with specific instrument, which made the surface of the alumina femoral head reach the degree of approximating mirror finish and match the femoral stem well. the artificial partial hip joint prostheses was finally got by articulating the alumina femoral head with ti alloy femoral stem coated with bioactive coating

    最後，採用sic超細粉和金剛石研磨膏對氧化鋁陶瓷股骨頭表面進行分級拋光，用專用器械修整其聯接部位，得到表面具有近似鏡面光潔度並與股骨柄配合良好的氧化鋁陶瓷股骨頭，並與表面塗覆生物活性塗層的鈦合金股骨柄配伍，最終獲得人工半髖關節假體。
  4. Between october 2003 and 2005 june, the authors performed 37 hip anatomic cementless tha in 35 patients with different clinical cases. twenty - five tha in 24 patients with the conventional methods were followed up for average of 18 months

    2 .回顧性分析了未使用模板進行的解剖型非骨水泥固定股骨假體的24位患者共25例全髖關節置換術，術后進行了平均18個月的隨訪。
  5. Objective ( l ) cases of fracture of femoral neck treated with artificial femoral head replacement were studied retrospectively to measure the acetabular wear by the metallic femoral head

    目的（ 1 ）隨訪觀察人工股骨頭置換術治療股骨頸骨折病例，測量金屬股骨頭對髖臼的磨損。
  6. Methods ( l ) to measure the acetabular wear with special computer soft ware program for 84 cases of femoral head replacement arthroplasties 1 - 6 years after the operation and to analyze the radiological acetabular wear with the clinical results

    材料與方法（ 1 ）利用計算機數字化方法計測84例人工股骨頭假體置換后1 - 6年髖臼的磨損，並對其磨損的臨床和放射學檢查結果進行分析。
  7. The patients were evaluated with harris hip score and radiographic analysis. results : dr - based surgical planning software had better proximal fit on postoperative x rays than the conventional method. in the clinical results the harris hip score using both methods was not significantly different between patients, 94. 5 % of patients had excellent or good results evaluated by harris hip scores post - operation

    再利用開發的基於數字x線股骨假體置換術前計劃軟體對11位患者共12例髖術前預估后進行全髖關節置換術，術后進行平均9個月的隨訪，上述兩組均通過harris評分及x線片評價臨床效果。
  8. ( 2 ) to introduce the methods of design and fabrication of surface arthroplasty prosthesis and operative instruments of hip joint and to present the preliminary clinical application ( 3 ) to evaluate the clinical results of resurfacing arthroplasty in the treatment of avascular necrosis of femoral head of the hip using the prosthesis designed by mcminn. ( 4 ) to study the pathological changes of the femoral heads suffering from osteonecrosis and osteoarthritis

    （ 2 ）進行髖關節表面置換假體及手術器械的設計製作與臨床近期療效觀察。 （ 3 ）評價mcminn假體髖表面置換術治療股骨頭缺血性壞死的臨床效果。 （ 4 ）研究股骨頭缺血性壞死與骨關節炎骨、軟骨的病理變化及細胞凋亡。
  9. Standard practice for cyclic fatigue testing of metallic stemmed hip arthroplasty femoral components without torsion

    無扭轉裝有金屬桿的髖關節成型術股骨部件的循環疲勞檢驗
  10. Modal change research for different load response femur after total hip replacement

    不同載荷靈敏度的股骨在全髖置換后的模態變化研究
  11. Standard test method for determining femoral head penetration into acetabular components of total hip replacement using clinical radiographs

    使用臨床射線攝影測定全部髖替換物的股骨頭穿透進髖組件的標準試驗方法
  12. Objective : to study the influence of head - neck ratio and implant position on the range of motion ( rom ) after total hip arthroplasty ( tha )

    摘要目的：探討不同股骨頭頸直徑比和髖臼安置方位對人工全髖關節活動范圍的影響。
  13. The preparation, mechanical properties of alumina material and machining of femoral head for bioceramic - metal articulated partial hip joint prostheses were studied in this paper, which provided the research results being worth theoretical reference and practical use for the solving of technical problems of sintering and machining of alumina ceramic

    本文研究高性能氧化鋁生物陶瓷?金屬配伍型人工半髖關節股骨頭材料的制備、力學性能及假體的成型加工工藝，為解決氧化鋁陶瓷燒結、機加工等技術難題提供具有一定理論參考和實際應用價值的研究結果。
分享友人
分享到 Line

分享到臉書