高共振電路 的英文怎麼說

中文拼音 [gāogòngzhèndiànlù]
高共振電路 英文
highly resonating circuit
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 共 : 共動詞[書面語]1. （圍繞） surround2. （兩手合圍） span with the hand
  • 振 : 動詞1. （搖動; 揮動） shake; flap; wield 2. （奮起） brace up; rise with force and spirit
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  • 電路 : [訊] circuit （ckt）; electric circuit; electrocircuit電路板 circuit board; 電路保持 guard of a c...
  1. Accurate simulation of switch circuit is needed in pin switch design, while limited by assembling techniques, serial resonance and channel inter - coupling exist in the common joint that bring a lot of difficulties for simulation. 2 - dementions simulation software can not establish accurate circuit mode for pin diode switch which gives simulation error, and it costs much more time with 3 - dementation simulation software, which is not applicable in practice for pin switch design

    Pin開關的設計中需要對開關電路進行準確模擬，然而高頻、寬帶、多擲pin開關受裝配工藝的限制，開關公共結點附近存在著串聯諧振和相互耦合，給pin開關的準確模擬帶來了困難:二維模擬軟體很難對電路進行準確建模，模擬誤差較大;三維模擬軟體耗時過長，難以在實際設計中應用。
  2. On the base of studying imaging theory of lens, the imaging theory of laser confocal scanning microscopy was analyzed in detail in this paper, and the advancement of that the optical fiber was applied to the system was described ; on the base of completed the demonstration for whole project, the experiment scheme was designed ; the relationship between the main parameters of key devices and the resolution was deduced, and the requirements of coupling efficiency and vignetting effects to optical system was analyzed ; the design of optical system and the planar scanning controlling circuit was completed ; a new method was put forward to resolved the inherent non - liner scanning problem of the galvanometer scanner by using software liner controlling in circuit design, and the perfect planar scanning was realized ; at last the low noise, high multiple and non - distortion amplify circuit of photoelectric detector was completed

    本文在透鏡成像理論的基礎上，系統、深入地分析了共焦掃描顯微成像的機理，論述了應用單模光纖的激光共焦掃描顯微成像系統的優點；進行了總體方案的論證，並設計確定了單模光纖激光共焦掃描顯微成像系統的總體方案；從理論上推導分析了解析度要求與試驗系統中相關器件主要參數之間的關系，分析了系統耦合效率和漸暈現象對光學系統的設計要求；完成了方案中光學系統和二維掃描控制電路的設計，並在電路設計中採用了用軟體解決檢流計式光學掃描器（振鏡）非線性問題的新方法，能夠實現較為理想的二維模擬掃描；完成了高增益、低噪聲和低失真的探測接收系統的設計和調試。
  3. The infrared component ( carborundum board, carborundum camp ) of carborundum, is used in the paint, food, medicine, print and dye the fabric extensively, binder, it is dry for integrated circuit to wait for, heat outside send out infrared electromagnetic wave organic matter in the course of heating far, high polymer and moisture son after drawing, produce member and atom resonance, make the object hot

    碳化硅紅外元件（碳化硅板、碳化硅營） ，廣泛用於油漆、食品、醫藥、印染織物，粘結劑，集成電路等乾燥，加熱遠外在加熱過程中發出紅外電磁波被有機物，高分子及水分子吸取后，產生分子和原子共振，使物體變熱。
  4. Diode switches or voltage controlled varactors implement dual - band resonators such that they can offer low impedance at the second harmonic of each frequency band, while, in some cases, presenting high impedance at the fundamental frequency as an rf choke circuit

    利用二極體開關或電壓控制變容器實施雙頻共振器以提供在雙頻操作中每一個頻段之二階諧波的低阻抗，同時在一些實施例里也提供主頻段的高阻抗、兼具有射頻阻塞電路作用。
  5. In order to gain high reliability, when designing pcb these questions must be considered : whether the first natural frequency of pcb is large enough or not ? what are the dynamic characteristics of pcb and where are the weak points of pcb

    因此，為了保證印製電路板的高可靠性，就必須在印製電路板的設計和振動分析過程中，考慮以下問題:印製電路板的固有頻率是多少，使用中是否會發生共振破壞
  6. By utilizing the knowledge of digital circuit and simulation circuit, the system designs the pretreatment dealing circuit of the myoelectrical signal, which has the feature of big input impedance well suppress of public module and high gains. then the signal is gathered with " zhentong " data gathering after dealing with, and the software of signal processing is explored before the myoelectric signal is analyzed. after picking up eigenvalue, it is proved that the result is unanimous basically with the data of the relevant materials ; the other is to control artificial hand by the eigenvalue of the myoelectric signa l and at last the system gets very good control results

    即利用數字電路和模擬電路等相關知識，設計了具有輸入阻抗大、共模抑制好、增益高等特點的肌電信號前置處理電路，利用「振通」數據採集儀對處理后的信號進行採集，並利用快速傅立葉變換的相關知識編寫了信號處理程序，對肌電信號進行了波形分析、幅值譜分析和功率譜分析，提取了信號特徵值，與相關資料的數據相比，基本一致；二是利用肌電信號的特徵值對肌電假手進行控制。
分享友人
分享到 Line

分享到臉書