高剪切 的英文怎麼說
中文拼音 [gāojiǎnqiē]
高剪切
英文
high shear-
Analytical method to calculate the stresses in the rotator of a high - shear homogenizer
高剪切均質機轉子應力的解析法分析Standard test method for explosive reactivity of lubricants with aerospace alloys under high shear
高剪切應力下潤滑劑與航空用合金爆炸反應性的標準試驗方法05. 02 explosive reactivity of lubricants with aerospace alloys under high shear, method of test for
在高剪切力作用下潤滑劑對宇航合金的爆炸反應性的試驗方法This model is engaged with integrated hydraulic system, which illustrates robust performance
採用三點支承滾動導軌，消除支承間隙，提高剪切質量。The recent research advances in the synthesis of styrene - butadiene latex for paper coating, including monomer composition, particle structure, balance of surface strength and blister resistance, coating with good fluidity at high speed, latex stability, additive and material addition sequence were reviewed with 15 references
摘要介紹了近年來國外塗布紙用丁苯膠乳在單體組成、粒子結構、塗布紙表面強度與抗起泡性的平衡性、塗料高剪切流動性、膠乳德定性、添加劑和加料順序等方面的研究進展。Acuum emulsion machine, high shear disperser
真空乳化機高剪切分散機Sbs elastomers do not depend on a high shearing rate to achieve the injection viscosity, but sebs elastomers are vice - versa
Sbs彈體無需依賴高剪切率來達至塑性流動力， sebs彈體卻需依賴高剪切率來達至塑性流動力Particulate reinforced metal matrix composites possess several additional advantages such as light weigh high specific strength and stiffness great shear strength. so they are widely used in many general applications in spaceflight car fittings sports goods areas. according to the difference of the wild phase ' s formation, the composite ' s manufacturing method can be divided into traditional way and in situ way
顆粒增強金屬基復合材料具有重量輕、比強度與比剛度高、剪切強度大等優點，因而被廣泛應用於航空航天領域和汽車配件、體育用品等行業，其製造方法一般分為外加法與內生法。2 % 22 % and 29 % respectively less than using other three knives at cutting speed of 500mm / min when the moisture contents of rootstalks was 48. 2 %. the cutting forces were tested at four different parts of rootstalk that were the middle part along a radius, the tip part along a radius, the middle part along axis and the stalk part along a radius, and the force at the middle along a radius is the largest and increase 32 % 45 % 111 %, respectively more than at the other three parts. the force increase 37 % to cut the rootstalks from the areas one crop a year more than that from two crops a year
試驗結果表明，根茬含水率愈高，剪切力愈小，根茬含水率與剪切力近似為二次曲線關系；刀片剪切速度愈快，剪切力愈小；凸曲線、斜線、凹曲線和直線四種不同的刀刃曲線對整株根茬剪切力依此由小到大，凸曲線和斜線剪切時有一定程度的滑切作用，所以剪切力相比較小，當根茬含水率為48 . 2 ，剪切速度500mm min時，與其他三種曲線相比凸曲線型刀刃的剪切力依次分別減少了7 . 2 、 22和29 ；對根茬中部、梢部和根部的剪切力，在相同試驗條件下，徑向中部最大，比梢部，軸向根部和根部莖稈所需剪切力分別增加32 、 45和111 ；當含水率為48 . 2 ，刀片的剪切速度為500mm min時，一年一熟玉米根茬比一年兩熟的玉米根茬剪切力增大37 。Rises but other parameters do n ' t almost vary. at of mrs based on composites is lower than that of mrs based on carbonyl iron, declines with the content of atpu increasing but the rising rate with h improves. with the content of spanso increasing, at declines, but the rising rate falls, and y max heightens
復合粒子的、 、隨著atpu用量的增加均降低，且頻散特性也有較大的變化，而隨著span80用量的增加，增加，其它參數基本不變；復合粒子組成的mrs的磁致剪切應力較羰基鐵粒子有很大的降低，隨atpu用量的增加降低，但隨h增加的速率提高，最高剪切速率_ （ max ）增加，而隨著span80用量的增加增加，但隨h增加的速率降低， _ （ max ）提加。Ht hs high temperature high shear viscosity
高溫高剪切粘度Standard test method for measuring apparent viscosity at high - temperature and high - shear rate by multicell capillary viscometer
用多孔毛細管粘度計在高溫高剪切率下測量表觀粘度的標準試驗方法Determination of viscosity of coatings at a high rate of shear
塗料在高剪切速率下粘度的測定Standard test method for measuring viscosity at high temperature and high shear rate by tapered - plug viscometer
高溫和高剪切速率下粘度測定法The general manufacturing temperature is between 200 and 230c and can be manufactured in high shearing rate
一般加工溫度在200230c間，可用高剪切率加工Test method for measuring viscosity at high shear rate by tapered bearing simulator viscometer at 100 c
攝氏100下用錐形承載模擬粘度計測量高剪切速率粘度的方法Standard test method to measure viscosity by tapered bearing simulator at high temperature and high shear rate
在高溫和高剪切率下用錐形承載模擬器測量粘度的標準試驗方法If the materials are degraded in the event of high temperature and high shearing rate, the melt viscosity will decrease due to the breaking up of the molecular bonds
如果材料因高溫或高剪切率加工而降解，熔膠粘度會因分子鏈斷裂而降低Test method for measuring apparent viscosity at high - temperature and high - shear rate by multicell capillary viscometer
用多孔毛細管粘度計在高溫和高剪切率下測量表面粘性的試驗方法08. 01 test method for apparent viscosity of plastisols and organosols at high shear rates by extrusion viscometer
用擠壓粘度計測定高剪切率下增塑溶膠和稀釋增塑糊的表觀粘度的試驗方法分享友人