高壓油泵噴油 的英文怎麼說
中文拼音 [gāoyāyóubèngpēnyóu]
高壓油泵噴油
英文
mechanical injection- 高 : Ⅰ形容詞1 (從下向上距離大; 離地面遠) tall; high 2 (在一般標準或平均程度之上; 等級在上的) above...
- 壓 : 壓構詞成分。
- 油 : Ⅰ名詞1 (脂肪; 油脂) oil; fat; grease 2 (姓氏) a surname Ⅱ動詞1 (用桐油、油漆等塗抹) apply t...
- 泵 : 名詞(吸入和排出流體的機械) pump
- 噴 : 噴動詞1. (液體等受壓力而射出) spurt; spout; gush; jet 2. (噴灑) spray; sprinkle
- 高壓 : 1 (殘酷迫害; 極度壓制) high handed 2 [氣象學] (高氣壓) high pressure3 (高電壓) high tension...
-
The investigation has declared that the fuel injection with bq fuel pump had higher injection pressure, bigger fuel supply rate and shouter fuel supply duration, which would cause the fuel injection quantity and the fule - air mixture to increase during ignition delay period, the pre - mixed combustion to become acutely, and finally result in increased power levels of noise
研究表明,裝配bq噴油泵,噴油系統的噴油壓力較高,供油速率較大和供油持續時間縮短,使得滯燃期的噴油量增加,滯燃期內形成的可燃混合較多,預混燃燒劇烈,導致整機噪聲聲功率級增加。Diesel engines - base - mounted in - line fuel injection pumps and high - pressure supply pumps for common rail fuel injection systems - mounting dimensions
柴油機.共軌燃料噴射系統用基座安裝直列式噴油泵和高壓供油泵.安裝尺寸Diesel engines - mounting dimensions of fuel injection pumps - part 2 : base - mounted in - line pumps and high - pressure supply pumps for common rail fuel injection systems
柴油發動機.噴油泵的安裝尺寸.第2部分:公軌燃料噴射系統用基座安裝直列多柱塞泵和高壓供給泵A method based on the application of an injection process analysis software is introduced in this article, which optimize injection process through changing the design of fuel - injection pump cam. a model of 1115 single cylinder direct injection diesel engine is used as an example. with the help of pre - journey optimization, increasing cam lift and using tangent - function can make the matching of the injection system with the diesel more reasonable. without changing fuel pump installing size, it can enhance injection rate and injection pressure and improve the diesel operating stability in low speed condition
本文以國產1115型單缸直噴柴油機為例,介紹一種應用噴油過程分析軟體改進噴油泵凸輪設計的方法,通過增大噴油泵凸輪升程、採用切線函數凸輪並優化預行程的方式,在不改變噴油泵安裝尺寸的前提下,可提高噴油壓力和噴油速率,改善柴油機低速工作穩定性,使噴油系統與柴油機匹配更合理。High pressure pipe assemblies for diesel fuel injection pump test bench
柴油機噴油泵試驗臺用高壓油管組件The injection fuel pump with 2. 5 mm diameter deliver pipe was analyzed and suitable for the power augmentation of tbd604b diesel according to the fuel injection pressure, fuel injection rate and duration of injection
經計算分析p10型噴油泵配用2 . 5mm高壓油管,從噴油壓力、噴油速率、噴油持續期等參數來看,完全可以滿足提高功率后的tbd604b柴油機對燃油系統的要求。Diesel engines - fuel injection pumps - high - pressure pipes for testing
柴油發動機.噴油泵.試驗用高壓管Road vehicles. fuel injection pumps. high - pressure pipes for testing
道路車輛.燃油噴射泵.試驗用高壓管Diesel engines - high - pressure fuel injection pipe assemblies - general requirements and dimensions
柴油發動機.高壓燃料噴射泵組件.一般要求和尺寸The construction of conical nozzle is used by pump ' s delivery - valve, making use of the dynamic characteristics of conventional. short pipe to enhance injection pressure. there are three parameters of fuel injection system : response pressure, injection - advanced angle, injection valve bulge high degree, the best match was found by adjusting them
在油泵出油閥端,採取漸縮管結構措施,利用管路動態效應提高噴油壓力;對于噴油系統參數:噴油壓力、靜態供油提前角和油嘴凸出高度,三個參數進行調整試驗,找到它們的最佳匹配。分享友人