高壓給料器 的英文怎麼說
中文拼音 [gāoyāgěiliàoqì]
高壓給料器
英文
high pressure feeder- 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
- 壓 : 壓構詞成分。
- 給 : 給Ⅰ動詞1 （送對方某物; 使對方得到） give; grant 2 （用在動詞后 表示交與 付出） pass; pay 3 （叫; ...
- 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
- 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
- 高壓 : 1 （殘酷迫害; 極度壓制） high handed 2 [氣象學] （高氣壓） high pressure3 （高電壓） high tension...
-
A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle
試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。The main work can be summed up as follows : firstly, we studied the thermal - field properties of vcsels, and analyzed the influences of current spreading, material parameters and operating conditions on the temperature distributions. secondly, we began with the electrode voltage and calculated the equipotential s distributions, compared the distributions of voltages and current densities in different depths of vcsels, and then studied the influences of the oxide - confining region with different position or thickness, and the different sizes of the gain - guided aperture and emitting window on the distributions of the injected current density, carrier concentration and temperature in the active region. thirdly, we realized the coupling of electricity, optical and thermal - fields, worked out the threshold voltage, calculated the distributions of the injected current density, carrier concentration and temperature under different offset voltages, and analyzed the impacts of temperature profile and carrier density on the refractive index, fermi levels and optical - field
具體工作可以概括如下：首先，研究了vcsel的熱場特性，分析了電流擴展，材料參數和工作條件對于溫度分佈的影響；其次，從電極電壓入手，計算出激光器中的等勢線分佈，並對不同深度處的電壓和電流分佈進行比較，研究了高阻區的不同位置和不同厚度、限制層和出射窗口半徑的大小對電流密度、載流子濃度和溫度分佈的影響；再次，實現了電、光、熱耦合，求出了閾值電壓，計算了不同偏置電壓下的電流密度分佈、載流子濃度分佈和熱場分佈，分析了溫度和載流子濃度變化對折射率、費米能級和光場的影響；最後，給出了考慮n - dbr和雙氧化限制層時激光器中的等勢線分佈，分析了n - dbr和雙氧化限制層對vcsel電流密度、載流子濃度、溫度和光場分佈的影響。This installation is composed of material feeder, implement of friction and decentralization, high voltage static separator, implement of grain collecting, wind pipe, wind machine
這套試驗裝置主要包括給料裝置、摩擦分散器、高壓靜電分離器、顆粒收集器、風管、風機等部分。
分享友人