高壓試壓泵 的英文怎麼說
中文拼音 [gāoyāshìyābèng]
高壓試壓泵
英文
high pre ure testing pump-
In pumping fluid with gas, pressure boost can be improved by enhancing the pump rotation speed, thereby improving the performance of the pump to a certain degree ; when the gas content is constant, by increasing the inlet pressure, the pressure boost can be enhanced and the pump efficiency be improved remarkably ; when the gas content is rather high, there will be a problem of matching between the gas pressure and the fluid pressure ; the performance of the multiphase pump can also be improved by means of rational design of buffer vessel and homogenizer
試驗分析認為,氣液混輸工況下,提高泵轉速可以提高增壓,在一定程度上能改善多相泵的工作性能;含氣率一定時,增加進口壓力,可使多相泵增壓值增大,泵效明顯增加,最大含氣率點后移,但含氣率很高時,存在氣液壓力相匹配問題;改進緩沖罐和均化器的設計,有利於氣液互相夾帶,避免氣囊產生,可改善多相泵的輸送性能。And at last the measurement of helical gear pump flow pulse has been presented, which include how to measure the flow pulse and the validating the theory mentioned before and to try to the solve the problems happened during the process
根據齒輪泵流量脈動的檢測要求,採用新的測試方法和手段,建立了中高壓齒輪泵性能測試裝置,並對樣機進行了性能測試。These characteristics and phenomenons have effect on the quality of gear pump, and it is difficult relatively to research them by theory. at present the research is limited to the phase of examination testing. theoretic research of the characteristics and the phenomenons of polymer gear pump are blank in china when the gear pump feeds the viscous polymer liquid of chemical flow with high temperature and high pressure
齒輪泵除具有流量和容積效率、扭矩和機械效率、功率和總效率等基本特性外,還存在著困油、噪聲和氣穴等現象,這些特性和現象直接影響齒輪泵的質量,對斜齒齒輪泵的這些特性和現象的理論研究難度較大,目前大多仍局限於實驗測試研究階段,而聚合物齒輪泵在輸送化工流程中的高溫、高壓的粘流態聚合物時特性的理論研究在國內基本還處于空白。A test - bed of dg45 - 80 10 hypo - pressure feed water pump is designed, based on which the general on - line performance testing system is developed and the thermodynamic method is introduced to measure the efficiency of the pump. a new programming technology combining vc + + with matlab is presented by which the vibration monitoring system of boiler feed water pump is developed successfully to perform data analysis after on - line acquisition
本文首先進行了次高壓鍋爐給水泵dg45 80 10實驗臺的設計,在此實驗臺設計成功並安裝調試通過的基礎上,開發了鍋爐給水泵通用性能試驗系統,包括測點的布置、各型測量儀器的選購,設計,安裝和調試以及軟體平臺開發。High pressure pipe assemblies for diesel fuel injection pump test bench
柴油機噴油泵試驗臺用高壓油管組件According to the concrete request of the test pump, this close test circuit project of the high pressure pump platform is made out
根據被試泵的具體要求,制定了高壓泵實驗臺的閉式實驗迴路方案。Diesel engines - fuel injection pumps - high - pressure pipes for testing
柴油發動機.噴油泵.試驗用高壓管Road vehicles. fuel injection pumps. high - pressure pipes for testing
道路車輛.燃油噴射泵.試驗用高壓管A transparent model is used to make the deflection jet board grounded on the inhere enlarged dimensions. the finished experiments are conducted to catch the flow rate directions and the situation of cavitation using a high - speed video cameras. in this paper, the finite element analysis and visualiation research of servo valve prestage jet flow field are carried out, which establish the theoretical foundation for mathematical model of servo valve prestage and the whole mathematical model of hydraulic servo valve
在對射流前置級驅動的伺服閥射流流場數值模擬的基礎上,用有機玻璃在偏導射流板原始尺寸的基礎上進行了擴大,製作了透明的偏導射流板,運用高速攝像機、液壓泵站等組成了可視化實驗系統,對射流流場的流速方向、渦流、氣穴等現象進行了多方位的觀測,並通過對接收管接收壓力的測試,對流場分析結果進行了驗證。The construction of conical nozzle is used by pump ' s delivery - valve, making use of the dynamic characteristics of conventional. short pipe to enhance injection pressure. there are three parameters of fuel injection system : response pressure, injection - advanced angle, injection valve bulge high degree, the best match was found by adjusting them
在油泵出油閥端,採取漸縮管結構措施,利用管路動態效應提高噴油壓力;對于噴油系統參數:噴油壓力、靜態供油提前角和油嘴凸出高度,三個參數進行調整試驗,找到它們的最佳匹配。Test method for indicating wear characteristics of petroleum hydraulic fluids in a high pressure constant volume vane pump
高壓定容葉輪泵中石油液壓液耐磨特性指示的試驗方法Responsible for hydraulic pump station system project manufacturing process and quality control, customer on - site service and adjustment of hydraulic pump station system. improve product quality and customer satisfaction
負責液壓泵站系統工程的製造流程和質量控制,以及現場客戶服務和液壓泵站系統的調試。以提高產品質量和客戶滿意度。Products are : super high pressure electric, pneumatic, manual oil pump ; pre - stress jack for the use of coal mine and construction ; steel bar and cable scissor ; all kinds of bolt for safety supporting and bolting ( km19 and km22 bolt have all got the certificate of “ ma ” in china. ) ; cable anchor and bolt test stand ; hydraulic nut scissor and etc
產品有防爆式超高壓電動、風動、手動油泵;煤礦、建築用預應力張拉千斤頂;鋼筋、鋼絞線切斷器;安全支護用各種錨具( km19 、 km22錨具在國內率先取得煤安證書) ;錨索錨具靜載拉伸試驗臺;液壓螺母破切器等。Moreover, high - pressure common rail system was found to be very effective for improvement of engine startability and reduction of white smoke at low temperatures
通過和採用機械泵原機對比試驗數據進一步說明,高壓共軌電控噴射系統使得發動機的經濟性和排放獲得了明顯的提高。分享友人